How to use natural gas wall hung boiler How to use natural gas wall hung boiler

Newly installed wall-hung boiler.

Fill the water first, and the method of filling the water is to open the exhaust valve first. Then open the make-up valve of the wall-hung boiler to replenish the water. The wall-hung boiler uses a leakage protection plug.

Press the ON button in the middle to turn on the power. For the first time, let the wall-hung boiler run on its own for 5 minutes. When the air in the system is almost exhausted, turn on the natural gas ignition.

Anti-freezing: The wall-hung boiler has an automatic anti-freezing function when it is turned on. Freeze protection on duty:

Set the function transfer switch to the summer state, i.e. small umbrella mode. When the water temperature is lower than 5, the wall-hung boiler will start automatically, and when the heating water temperature reaches 42, the wall-hung boiler will stop running. Low temperature freeze protection:

Set the function transfer switch to winter snowman mode, and set the water outlet temperature to 35 by adding or subtracting on the right side of the display. The wall-hung boiler will always run at a low temperature of 35 °C. It will automatically stop when the water temperature reaches the set value, and will automatically start when it is lower than the set value.

Install a manual thermostat.

, the function transfer switch of the wall-hung boiler is placed in the heating operation state, and the indoor thermostat is placed at the snowflake. Master Villa provides you with local building policies, architectural drawings, villa design drawings; Villa exterior renderings service, you can choose from thousands of red hot drawings.

1. Plug in the plug of the natural gas wall-hung boiler first, and then turn on the switch button above, and the green indicator light will flash.

2. Turn on the switch that controls hot water and cold water, and generally twist it in a clockwise direction.

3. Adjust the temperature on the control interface, adjust the temperature to a suitable position, and the wall-hung boiler will be automatically heated.

4. After turning on the faucet, hot water will flow out.

Natural gas wall-hung boiler.

In recent years, it has been widely used, it can not only provide domestic hot water for families, but also meet the water supply of household heating equipment, and many household users are very favored. However, there are certain skills in the use of natural gas wall-hung boilers, if used correctly, the use efficiency of wall-hung boilers can be improved, and the use of natural gas can be saved.

1. How to select the operation mode of the wall-hung boiler:

The standard natural gas wall-hung boiler provides two modes of operation: heating and sanitary hot water. control panel in the natural gas wall-hung boiler.

In the winter stall, the natural gas wall-hung boiler can provide heating and sanitary hot water functions, and the sanitary hot water function is preferred, so the natural gas wall-hung boiler will automatically switch in the heating and sanitary hot water mode according to the user's sanitary hot water usage.

In the summer gear, the natural gas wall-hung boiler is usually in standby mode, and only enters the sanitary hot water mode to work when the user uses sanitary hot water. Therefore, users can choose the winter mode when they need to heat and use sanitary hot water in winter, and choose the summer mode for the rest of the time, and only use the sanitary hot water function.

2. How to use heating and hot water functions:

Europe. The standard natural gas wall-hung boiler heating and sanitary hot water modes cannot be operated at the same time, and the sanitary hot water function is preferred, and the natural gas wall-hung boiler automatically switches between the two according to the use of sanitary hot water.

Heating function: In standby mode, press the heating temperature adjustment button " to raise the set temperature to 30 80, the green indicator light is always on, the display screen shows the temperature of heating hot water at that time, the circulating water pump starts, and the circulating water pump flows the heated water through the radiator installed in the room to send out heat, so that the room temperature rises, so as to achieve the purpose of heating.

Sanitary hot water function: In standby mode, open the sanitary hot water outlet valve, the green indicator light on the adjustment panel flashes, then the heating valve is closed, the hot water circulation valve is opened, and the hot water flows out from the sanitary hot water outlet.

3. Precautions for the use of natural gas wall-hung boiler.

When the wall-hung boiler is working, the temperature of the heating, hot water outlet pipe, and smoke pipe at the bottom is high, and it is strictly forbidden to touch it to avoid scalding.

If necessary, an indoor temperature controller can be installed, and the indoor temperature can be automatically adjusted through the controller, which can effectively control the size of the flames in the wall-hung furnace and save the amount of natural gas. When there is no one at home, the natural gas wall-hung boiler can be adjusted to the economical and energy-saving operation program, and the function key of the wall-hung boiler in the anti-freezing protection can be set to ensure that the heating and water supply temperature of the wall-hung boiler is not lower than the anti-freezing setting value of 5. In addition, regular maintenance and maintenance can ensure the high thermal efficiency of the boiler.

How to use natural gas wall-hung boiler? The above introduces the basic use methods and precautions of natural gas wall-hung boiler, and only scientific and reasonable use can make the life of the wall-hung boiler longer.

Install the wall-hung boiler and fill the wall-hung boiler with water; Then plug in the power supply, turn on the switch, let it run for 5 minutes, and ignite it after the water pressure is stable; Finally, you can adjust the desired water temperature, usually in winter, you can adjust the water temperature to 40 degrees, not too high, to avoid burns. In addition, when using a wall-hung boiler, in order to avoid indoor heat loss, the doors and windows should be closed.

There are generally instructions for the decoration and use of gas wall-hung boilers, but there are also some tips. If the gas wall-hung boiler can be used correctly, it can save energy and prolong its service life to a certain extent.

Gas wall-hung boiler 1Water pressure setting.

The standard water pressure specified in the general instruction manual is Pa. In fact, it will not affect the normal use of the gas wall-mounted pre-land argument furnace. Therefore, when using it, it is necessary to pay attention to the water pressure, if it is lower than that, it will not be able to start normally, and if it is higher than that, it may automatically drain the water, resulting in losses.

Gas wall-hung boiler 2Pay attention during use.

Ensure that the smoke pipe exhaust of the wall-hung boiler is usually unusual, and has been protected from hazards.

During the use of the wall-hung furnace, the bottom is hot, do not touch it.

In winter, it is still necessary to do a good job of anti-freezing measures, and the current wall-hung boiler generally has an anti-freezing function, so please refer to the manual.

Gas wall-hung boiler 3Tips and tricks in the process of use.

It is best not to open the faucet too much to save water. If you want to be more comfortable, you can start small and then big;

Close or lower the radiator valve in the uninhabited room, and when no one is at home during the day, you can adjust the wall-hung boiler to the lowest gear, and it is not advisable to turn it off and come back and heat it rapidly, this method is very unscientific.

The problem of limescale should be taken seriously. It is also necessary to choose a wall-hung furnace with a closed design, which will not cause oxidation and reduce the probability of scaling.

1. Check the gas wall-hung boiler. Before use, it is necessary to make sufficient preparations, first check whether the water, electricity and gas valves are opened, and carry out a series of corresponding safety inspections, so as to ensure that the gas wall-hung boiler has no water leakage, gas leakage and electricity leakage, and can be used normally.

2. Adjust the pressure. When using a gas wall-hung boiler, you must remember that the pressure must not be too high, too high pressure will reduce the normal service life of the sealing parts, so in general, the pressure can be controlled below It will be better. Of course, if the pressure is lower, there may also be a situation where it cannot be started, so at this time, it is necessary to release water and add water to operate.

3. Adjust the water temperature. In the process of using the gas wall-hung boiler, you can choose what kind of water temperature you want with one click, but you should pay attention to the use of the wall-hung boiler Do not use hot water to mix cold water, this method is wrong. Because the hot water of the wall-hung boiler is generally not directly heated, if it is mixed with a certain amount of cold water, the pressure of the scalding system may be changed to accelerate aging, and the equipment cannot operate normally.

4. Select the operation mode. There are a total of 5 operating modes of gas wall-hung boiler, you can directly press the button on the operation panel to select the operation mode, or you can also use intelligent adjustment, this gas wall-hung boiler has an intelligent system, through intelligent adjustment, the temperature control can be more accurate.

5. Clean the gas wall-hung boiler. The gas wall-hung boiler generally has the function of heating and hot water, but in the process of long-term use, the gas wall-hung boiler will have ash, carbon deposit, scaling, seal aging, and drift of the set working point, so the gas wall-hung boiler needs to be cleaned and maintained regularly during use, and it should be noted that the work of cleaning and maintaining the gas wall-hung boiler needs to be carried out by professionals.

1. Water injection. 1) After the gas wall-hung boiler is installed, the wall-hung boiler needs to be injected with water first. We should first open the exhaust valve of the wall-hung boiler, and then open the water make-up valve of the wall-hung boiler, so that the wall-hung boiler can start to fill water.

In the process of water filling, we should observe whether there is water flowing out of the drain valve.

2) If you find that there is water flowing out of the drain valve, it means that the wall-hung boiler has been filled with water, and the drain valve of the wall-hung boiler should be closed. In addition, we should also observe the value in the air pressure gauge on the wall-hung boiler, and when the value reaches about it, we should close the water replenishment valve of the wall-hung boiler. At this point, the water injection operation is complete.

2. Power on. After the wall-hung boiler is filled with water, we also need to electrify the wall-hung boiler before it can be used. The plug used in the wall-hung boiler is generally a leakage protection plug, and we only need to press the switch button on the plug to make the wall-hung boiler connect to the power supply.

3. Test run.

After the wall-hung boiler is connected to the power supply, you should let the wall-hung boiler run it first. We should let the wall-hung boiler run automatically for about five minutes, and when the air in the wall-hung boiler system is discharged, the water pressure in the wall-hung boiler system will become more stable, and then the wall-hung boiler can be clicked. Next, you can use the water in the gas wall-hung boiler as you like.

4. Temperature setting.

When you run the gas wall-hung boiler for the first time, the water temperature will generally be relatively cold, so it is recommended that you do not set the temperature too high, if the temperature is set too high, it is easy to let the wall-hung boiler run for a long time, but it is still impossible to reach the set temperature.

5. Adjust the temperature of the bathing water.

When using the gas wall-hung boiler in winter, the temperature of the gas wall-hung boiler should be set below 42 degrees, if the temperature is set too high, it is easy to burn people. When using a wall-hung boiler with a large number of gas in summer, it is more appropriate to set the temperature at about 40 degrees.

1. The wall-hung boiler just installed by Mingbi is injected with water first, and the water injection method is to open the exhaust valve with Huaiyan first.

2. Senju then opens the water replenishment valve of the wall-hung boiler for water replenishment.

3. The leakage protection plug is used in the wall-hung boiler, and the power supply can be turned on by pressing the on/off key in the middle.

4. Use the wall-hung boiler for the first time and let the wall-hung boiler run by itself for 5 minutes, and then turn on the natural gas to ignite when the air in the system is almost exhausted.