How to get off the white ash on the wall of the tile wall in the home?

Shovel it down. Take a shovel and slowly shovel off the white ash from the wall.

All you need to do is clean it with a cleaner and then sand it with a wire brush, and it will make the tile surface as good as new.

You can rub it vigorously with a damp towel so that it can all be removed.

There are two types of paving methods: tile adhesive thin pasting method and cement mortar wet paving method.

Tile adhesive thin lamination method:

Check whether there is hollow drum delamination on the lime mortar wall of the wall, the firmness and flatness of the lime mortar layer, if the lime mortar layer wall has the above problems, it is necessary to remove the problematic place for rectification, brush the interface agent at the base level, and use tile adhesive to paste the tile.

Cement mortar wet paving method:

The lime mortar layer on the surface is removed, the uneven surface is plastered with cement mortar, and the wall is brushed after it is dried; (Note: Before doing cement mortar brushing treatment, the dry cement mortar plastering wall needs to be sprinkled with water and moistened, and the purpose of sprinkling water is to prevent the dry wall from absorbing the water in the brushed mortar too quickly), after the brushing layer is dry, sprinkle water and moisten the brushing layer, and then use cement mortar to paste the tiles.

Remarks: The cement of the tile is ordinary Portland cement with a strength of megapascals, and the sand is medium river sand, and its ratio is proportioned according to the volume ratio, generally speaking, the ratio of cement sand paved with full ceramic tiles is about 1:2, and the volume ratio of cement sand paved with ceramic bricks is 1:3.

Tile adhesive thin lamination method:

1. First check whether the lime mortar wall of the wall is hollow and delaminated, and the firmness and flatness of the lime mortar layer;

2. If there are the above problems on the wall of the lime mortar layer, the problematic places need to be removed for rectification;

3. Brush the interface agent on the base layer;

4. Use tile adhesive for tile pasting.

Cement mortar wet paving method:

1. Remove the lime mortar layer on the surface;

2. The uneven surface is treated with cement mortar, and the wall is brushed after it is dried; (Note: Before doing cement mortar brushing treatment, the dry cement mortar plastering wall needs to be sprinkled with water to moisten it, and the purpose of sprinkling water is to prevent the dry wall from absorbing the moisture in the brushed mortar too quickly);

3. After the brushing layer is dry, sprinkle water on the brushing layer for moistening, and then use cement mortar to paste the tiles.

Remarks: The cement of the tile is ordinary Portland cement with a strength of megapascals, and the sand is medium river sand, and its ratio is proportioned according to the volume ratio, generally speaking, the ratio of cement sand paved with full ceramic tiles is about 1:2, and the volume ratio of cement sand paved with ceramic bricks is 1:3.

Question: It is best to shovel out the white mortar from the plastering cement mortar and blow it on the wall tiles.

Answer: first check whether there is a hollow drum delamination on the lime mortar wall of the wall, the firmness and flatness of the lime mortar layer, if the lime mortar layer wall has the above problems, it is necessary to remove the problematic place for rectification, brush the interface agent at the base level, and use tile adhesive to paste the tile.

It is best to scrape off the white ash to expose the sand-plaster wall, and the tiles are more stable. It is impossible to take it directly or with adhesive tape, and it cannot stand the test of time.

Shoveling the surface is the best way, if you want to save money in the paint that can be removed from the surface layer, it is not allowed, it must be dropped, and the pure white ash wall is left with a layer of cement paddle on it. Add some construction glue to the cement paddle, otherwise it will dry too quickly and it will be useless if it is dehydrated. Wet the wall with more water before shabu-shabu.

Wait until the next day to paste the brick is generally fine, but it is not as strong as the pure cement base wall, and it is feasible not to make a pool, and we have a lot of use this method

The ** of shoveling the wall is not high, just shovel the wall.

I don't think it's because of how high-end and elegant the wall is the decorative design of ceramic tiles, and the actual effect of taste? On the contrary, because it has an impeccable dirt-resistant effect, in any wall decoration material, the stain-resistant ability of ceramic tiles should be ranked first! Many people do not initially choose tiles for wall decoration when decorating their houses, and then find that the original selection of building decoration materials is not as extreme as originally thought, and they want to dismantle and replace them with ceramic tile decoration design.

However, it is okay to tile the wall, but the original decoration of the wall needs to be removed before the tile work can be carried out, so I have the question asked by this good friend: "How to make the lime of the tile wall?" According to the quality of the lime scraped on the wall, the first set of "shoveling" plan was made, and the specific steps were divided into these parts.

First of all, the lime tap water scraped on the wall is wet, so that the water can penetrate into the internal structure of the bottom layer of the wall, and the purpose is to soak the lime of the wall to make it soft and reduce the difficulty of shoveling it! After the lime on the wall is moistened, use special tools such as gray knives to shovel off the lime, and the "gray knife" special tools are very diverse, and you can freely make your own tools. For example, use a piece of cutter head to make a special gray knife for shoveling walls!

In fact, "grinding the wall" is a particularly hard thing, not only fortunate and the dust environmental pollution is relatively large, but also the risk factors are higher, the application of the grinder to grind the wall is not recommended by professionals to do so practically. Therefore, it is not a last resort and it is not easy to perform this secret**!

Prepare a bucket in advance (the kind of painter who rolls architectural paint), and the tap water can be rolled up several times, which will be very good shoveling. If you really can't get entangled, then stick the tile. To remove the lime powder of the wall, the general way of use is a very traditional practice, but also very reasonable, immediately shovel off with a flat shovel, be sure to maintain the flatness of the wall.

First wet the tap water, then use a gray knife, quickly. If you have to shovel the concrete surface of the tiles, it is a little inconvenient, the area is not large or you have time to gradually get it, pay attention to the safety protection work:

How to decorate the tile when it touches the small white wall, how to paste the tile is not easy to fall off the wall hollow, the small white wall belongs to the secondary decoration, the wall is a lime wall or the putty powder on the inner wall needs to be shoveled off, the wall decoration is slowly aging with time, and the putty powder layer on the wall will loosen offSome community owners don't understand why they want to shovel the wall, shovel off the big white powder on the wall, the key is to make the tile stronger and the cement slurry layer bonding, to avoid the tile wall hollowing down.

You can wet it with water, but don't water too much, shovel it with a shovel in a semi-dry and semi-wet state, and then paint the wall with hydrated lime high, and be sure to brush it several times when you go on the wall, and then brush it a second time when it is dry.

It can be cleaned with a broom, which can be cleaned or wiped with a rag.

The skin can be removed with some shovels and then sanded so that it can be cleaned.

There are two types of paving methods: tile adhesive thin pasting method and cement mortar wet paving method.

Tile adhesive thin lamination method:

Check whether there is hollow drum delamination on the lime mortar wall of the wall, the firmness and flatness of the lime mortar layer, if the lime mortar layer wall has the above problems, it is necessary to remove the problematic place for rectification, brush the interface agent at the base level, and use tile adhesive to paste the tile.

Cement mortar wet paving method:

The lime mortar layer on the surface is removed, the uneven surface is plastered with cement mortar, and the wall is brushed after it is dried; (Note: Before doing cement mortar brushing treatment, the dry cement mortar plastering wall needs to be sprinkled with water and moistened, and the purpose of sprinkling water is to prevent the dry wall from absorbing the water in the brushed mortar too quickly), after the brushing layer is dry, sprinkle water and moisten the brushing layer, and then use cement mortar to paste the tiles.

Remarks: The cement of the tile is ordinary Portland cement with a strength of megapascals, and the sand is medium river sand, and its ratio is proportioned according to the volume ratio, generally speaking, the ratio of cement sand paved with full ceramic tiles is about 1:2, and the volume ratio of cement sand paved with ceramic bricks is 1:3.

When it comes to decorating a house, tiling is an important construction project. Therefore, can white plaster walls be tiled? How do I deal with it?

It's a matter of people's hands. Today, we're going to put together these for you. Here's how to deal with white gray wall tiles.

Can white plaster walls be tiled?

1. Prepare for construction.

1) The wall should be carefully cleaned before construction, and it should be watered and moistened the day before.

2) Cut one end of the corner corner base according to the desired amount, cut it to 45° with a toothless saw, wash the base with water and dry it in the shade.

3) When assembling, start from the front to both sides, and check whether it is straight, whether the separation is narrow, whether there are missing corners, etc.

Can white plaster walls be tiled?

4) Regardless of the method used for installation, first place the base at both ends of the wall. The height of the top edge must be on the same horizontal line and the wall thickness must be the same. Then, the two upper sockets are installed one by one along the tow line, in order.

Can white plaster walls be tiled?

2. Construction methods.

1) Gluing method. According to the standard ribs of the wall and the standard horizontal line, the bottom ash is stained with 1:cement mortar and the stroke is smoothed.

After the lower mortar is dry and hard, the wet and dry tiles are applied to a smooth cement slurry of 2-3 mm for bonding. Gently pat with a rubber mac and use a ruler to level and straighten at any time. The next day, the joints are cleaned using a cement slurry of the same color as the floor.

Can white plaster walls be tiled?

2) Grouting method. Temporarily fix the tiles in the installation position, stabilize the two adjacent tiles and tiles with plaster with the floor and walls, then apply the grout with cement mortar 1:2 (volume ratio) with a consistency of 10-15 cm and wash the poured mortar at any time.

After the final insertion of the cement mortar to be poured, the plaster is scraped off and cleaned, and the cement is rubbed with the same color as the surface of the slab.

The above is the content written today about lime wall tiling, I hope to help those who just want to put tiles on white gray wall.

You can get it for free