What s wrong with the edge banding machine cutter not coming back

The travel switch of the machine is damaged, or the wire of the travel switch is loose, causing the wire to fall, and the plate cannot be sensed when passing through the travel switch, resulting in the cutter not moving.

The edge banding machine cutter does not come back, this may be because the remote area is too big now, or there are some problems with this line, so he should have no way to come back.

If the edge banding machine does not come back, it should be that the program is not set up, so it blocks the way forward.

Normally, this knife should be able to go back, if you can't go back, then it may be stuck, so it is recommended to check it well, and then use it should be okay.

Hello, my friend can't come back, if he doesn't come back, there must be a problem, or he can't come back if he is stuck. Hope it helps.

What's wrong with the edge banding machine cutter not coming back, isn't it like this, it doesn't come back, it may be broken.

If the edge banding machine cutter does not come back, he should find a professional to repair it, deal with it, and he should come back in the future.

If those are out of order, find a master to fix them for you, and they will be fine soon.

What's wrong with the edge banding machine cutter not coming backIf the screw is loose, it is stuck, so if it is stuck, you need to use your own hands to automatically deduct the things in the card slot, and then tighten it to operate normally.

This should be a mechanical collision to see if the spring is still stressed, and if not, it needs to be replaced.

Failure, it is recommended to restart after a power outage, if you can't solve it yourself, it is recommended to ask after-sales after all, safety first.

Sell it directly, always buy a new one, so higher.

Well, maybe it's because it's broken or something.

It should be that this device is malfunctioning, and it doesn't go back**, so it is recommended that you modify it.

This problem, in this case, generally don't do it yourself, just find a professional maintenance personnel to adjust it.

In this case, it should be that there is a problem with the parts in you, or there is a problem with the ** line, it is recommended that you check it.

How to solve the problem of not cutting the head in front of the edge banding machine, the reason why the edge banding machine is not cut in front of the edge banding machine is: the edge banding powder produced by the rough trimming knife flies to the sliding track where the rear knife is located, so that the whole motor of the rear head knife can not fall or rise, the second kind is to see whether the rear knife is in contact with the induction iron sheet above the rear knife when it runs Li Infiltration, and generally the contactor will light up the red light, and the third is to see whether the rear knife air pressure gauge on your horizontal slide is turned off, no air pressure**, Which filial piety spine, and then look at whether the air pressure control valve at the point where the two black tracheas connected to the back knife are twisted. I hope I can help you!

If my answer is helpful to you, please give a thumbs up (comment in the lower left corner), look forward to your like, your efforts are very important to me, your support is also the motivation for my progress, and finally I wish you good health and a happy mood!

Summary. There are generally two situations if the edge banding strip is not cut: the first is that the air compressor is not opened, or it is under maintenance, and there is no air ** resulting in the cutter not moving, and the solution is to start or wait for the machine to repair and repair the air compressor, and then start the edge banding machine for operation.

The second is that the travel switch of the machine is damaged, or the wire of the travel switch is loose, resulting in the steel wire falling, when the plate can not be sensed when passing the travel switch, which leads to the cutter does not move, solution: the steel wire that falls off or the height has decreased to a certain height, and then put a plate to check whether the height of the steel wire is reasonable, if the cutting belt is too fast, the height of the steel wire is increased and then fixed, and if the remaining belt is too long, the height of the steel wire is reduced.

Hello. There are generally two situations when the edge banding strip is not cut: the first is that the air compressor machine is not opened, or it is under maintenance, and there is no air ** resulting in the cutter not moving, and the solution is to start or wait for the machine to repair and repair the air compressor, and then start the edge banding machine for operation.

The second is that the travel switch of the machine exciter is damaged, or the wire of the travel switch is loose, resulting in the steel wire falling, Mingsun can not be sensed when the plate passes through the travel switch, which leads to the cutter does not move, the solution: the steel wire that falls off or the height has decreased to a certain height, and then put a plate to test whether the height of the steel wire is reasonable, if the cutting belt is too fast, the height of the steel wire is increased and then fixed, if the remaining belt is too long, the height of the steel wire is reduced.

The first board went straight to the head, and then the knife couldn't get up.

It's a question of what it is.

The head of the edge banding machine.

1. First of all, see if there are burrs on the contact surface of the edge banding machine, if there are burrs on it, wipe it off with fine gauze. Secondly, it is necessary to see whether the guide wheel of the edge banding machine is missing, if the guide wheel is missing, then the new guide wheel should be reinstalled, so as not to cause the appearance of the ruler knock plate. Secondly, the travel switch of the downward signal in front of the edge banding machine is faulty, for example, He Han said that its position is wrong or broken, so that when the plate travels to the predetermined position, if the travel switch is not touched or the switch is broken, then, there is no downward signal in front of the edge banding machine, and there will be a knock.

Hello Kiss is happy to answer this question for you. What is the reason why the edge banding machine is not cut behind the belt, the first is that the air compressor is not opened, or in maintenance, no air ** causes the cutter to not move, the solution is to start or wait for the machine to repair and repair the air compressor, and then start the edge banding machine for operation. The second is that the travel switch of the machine is damaged, or the wire of the travel switch is loose, resulting in the wire falling and buried, and the plate cannot be sensed when passing through the travel switch, which leads to the cutter not moving, solution:

Restore the steel wire that falls off or has decreased in height to a certain height, and then put a plate to check whether the wire height is reasonable, if the cutting belt is too fast, increase the height of the steel wire and then fix it, if the remaining belt is too long, reduce the height of the steel wire, I hope it can help you. If my answer is helpful to you, please also give a thumbs up (comment in the lower left corner or oh), look forward to your like, your efforts are very important to me, and your support is also the driving force for my progress. Finally, I wish you good health and a good mood!

Summary. 1.If the air compressor is not turned on, or it is under maintenance, and there is no air, the cutter does not move, and the solution is to start or wait for the machine to repair and repair the air compressor, and then start the edge banding machine for operation.

2.The travel switch of the machine is damaged, or the steel wire of the travel switch is loose, resulting in the steel wire falling, when the plate can not be sensed when passing through the travel switch, which leads to the cutter does not move, solution: the steel wire that falls off or the height has decreased to a certain height, and then put a plate to check whether the steel wire height is reasonable, if the cutting belt is too fast, the steel wire height is increased and then fixed, and if the remaining belt is too long, the steel wire height is reduced.

1.If the air compressor is not opened, or the loser is in maintenance, and there is no air, the cutter does not move, and the solution is to start or wait for the machine to repair and repair the air compressor, and then start the edge banding machine for operation. 2.

The machine's stroke inspection limb switch is damaged, or the wire of the travel switch is loose, resulting in the wire falling, when the plate can not be sensed when passing through the travel switch, resulting in the cutter does not move, solution: the steel wire that falls off or the height has decreased to restore a certain height, and then put a piece of plate to check whether the height of the wire is reasonable, if the cutting belt is too fast, the height of the steel wire is increased and then fixed, if the remaining belt is too long, the height of the steel wire is reduced.

1.If the air compressor is not opened, or the loser is in maintenance, and there is no air, the cutter does not move, and the solution is to start or wait for the machine to repair and repair the air compressor, and then start the edge banding machine for operation. 2.

The machine's stroke inspection limb switch is damaged, or the wire of the travel switch is loose, resulting in the wire falling, when the plate can not be sensed when passing through the travel switch, resulting in the cutter does not move, solution: the steel wire that falls off or the height has decreased to restore a certain height, and then put a piece of plate to check whether the height of the wire is reasonable, if the cutting belt is too fast, the height of the steel wire is increased and then fixed, if the remaining belt is too long, the height of the steel wire is reduced.

Summary. Hello dear, happy to answer your <>

What's wrong with the edge banding machine cutter not coming back: the reasons are as follows:1

Impurities are inserted inside the cylinder itself, occasionally stuck, and occasionally not stuckThe sealing ring inside the cylinder is damaged and leaking. Causing air leakage from the cylinder.

What's wrong with the edge banding machine cutter not coming back

Hello dear, I'm happy to answer for you [Taikai and Shen Tuanxin] <> what happened if the edge sealing Xiaoyan machine cutter didn't come back: The reasons are as follows: 1

The cylinder itself is incorporating orange and occasionally stuck, and occasionally not stuck2The sealing ring inside the cylinder is damaged and leaking. Causing air leakage from the cylinder.

Kiss Burn and kiss Hello <>

The expansion for you is as follows: [Happy Call] <>

The edge banding machine is a highly automated machine that replaces the manual edge banding procedures: conveying, gluing and welting, cutting, front and back scalp macroscopic, upper and lower trimming, upper and lower fine trimming, upper and lower scraping, and polishing, which are mainly divided into semi-automatic and hand-held. Edge banding machine is a type of woodworking machinery.

Dear, hello, I have checked the results for you; There are the following reasons why the edge banding machine cutter does not come back: 1Cutter jamming:

The cutter may be stuck in the build-up of edge banding material or other foreign objects. This can be caused by the accumulation of dust, leftover glue or wood chips from the cutting process on the cutter. The solution is to clean the area around the cutter to make sure the cutter can move freely.

2.Knife Damage: The cutter may be damaged due to wear and tear or bump over time.

The cutting edge of the cutter may become dull or deformed, preventing the cutter from returning to its normal position. In this case, the cutter needs to be replaced or repaired. 3.

Knife drive failure: The drive system of the edge banding machine may malfunction, resulting in the cutter not being able to return to its original position. This can be caused by a faulty motor, a broken drive belt, or a problem with the sensor, etc.

In this case, the individual components of the drive system need to be inspected and faulty parts repaired or replaced. 4.Control System Issues:

The control system of the edge banding machine may malfunction, resulting in the cutter not being operated correctly. This can be caused by a faulty circuit board, an error in the control program, or an abnormal sensor signal, etc. The control system needs to be carefully checked, the circuit repaired, or the control program readjusted.

Hello, dear. The first is that the air compressor is not opened, or it is under maintenance, and there is no air **, resulting in the cutter not moving, the solution is to start or wait for the machine to repair and repair the empty sail open press, and then start the edge banding machine for operation. The second is that the travel switch of the machine is damaged, or the wire of the travel switch is loose, resulting in the steel wire falling, and the plate cannot be sensed when passing through the travel switch, which leads to the cutter not moving, solution:

The falling off or height of the state chain has decreased the state of the wire to restore a certain height, and then put a piece of plate to check whether the height of the wire is reasonable, if the cutting belt is too fast, increase the height of the wire and then fix, if the remaining belt is too long, reduce the height of the wire.