Printer repeatedly jumps to toner cartridges? What should I do if the printer s toner cartridge is r

If this happens, it is likely that the computer version is malfunctioning, and in this case, the computer version must be replaced, and only then can a good effect be achieved.

The reason why the printer is repeatedly beating is caused by a fault, and you can find a professional to repair it.

The printer repeatedly jumps to the toner cartridge, which means that the printer is faulty, and you can find after-sales service to repair it.

1. The toner cartridge is not installed correctly, and the toner cartridge is reinstalled after pumping;

2. The dust falls to the charging point and the corona wire cannot be charged, and the machine reports an error toner cartridge error, so you need to disassemble the drum holder and clean the grating net and corona wire.

3. The contact of the toner cartridge is deformed, and the error is reported when the toner cartridge is turned on: the toner cartridge is wrong, and the left contact of the toner cartridge needs to be trimmed.

4. If the high-voltage plate fails, the high-voltage plate needs to be replaced.

The printer keeps showing replacement cartridges and ink cartridges for the following reasons:

1. If there is a problem with the quality of the cartridge, replace the cartridge with a new cartridge for testing;

2. If there is a problem with the quality of the cartridge chip, contact the after-sales service to replace the chip;

3. If the cartridge is not installed correctly, reinstall the cartridge;

4. There is a problem with the main control board of the printer, and the ink cartridge cannot be detected.

Repeatedly use the printer's mode options, adjust them over to normal parameters, and you can get it back.

If this is the case, I suggest you check your printer's settings, most likely there is a problem with the settings.

If this happens to your printer, it is recommended that you find a repairer to take a look so that you can use it as soon as possible.

It may be that there is no ink, so it is recommended to change it.

There are two cases:

1. If the printer toner cartridge is an easy-to-add toner cartridge, when it is about to run out, you need to take the toner cartridge out of the printer, open its waste toner port, clean up the waste toner (empty the waste toner magazine), add powder (need its suitable model of toner), and then reload the printer for printing after adding powder.

2. If the printer toner cartridge does not have a powder design, when the toner cartridge is about to run out, you need to replace it with a new toner cartridge to print.

In addition, under normal circumstances, when the color of the printed document is very light or the print is completely white, it may be caused by the toner cartridge running out of use, and you need to replace the toner cartridge with a new one in time.

The printer prompts that the toner cartridge will be exhausted, and it is time to replace the toner cartridge;

If you just replace a new toner cartridge, it still indicates that the toner cartridge is exhausted and you need to clear it, and different models of printers have different ways to clear it.

Toner cartridges, also known as photosensitive drums, generally consist of a basic substrate made of aluminum and a photosensitive material coated on the substrate.

Using the zeroing instruction, the state (data) of the memory can be changed to the original zero state. That is, the memory is flipped from a high potential (representing logic 1) to a low potential (representing logic 0).

When you run out, you need to change or add powder.

As far as the description goes, the toner cartridge is a whole. If you are referring to compacts. Add powder, you can't add it, you can only replace it. If you are referring to the imaging drum, then you can only replace it with a new one.

I don't know how to continue asking, satisfied.

1. The toner in the cartridge is exhausted

In this case, you need to turn off the printer switch, open the front cover, take out the toner cartridge, separate the drum holder and the compact, on the right side of the compact, there is a lid of the powder bin, use needle-nose pliers to open the lid and pour out the waste powder inside, and pour the matching powder into the powder bin and close the lid to add powder. Next, the cartridge is cleared, there is a clip on the left side of the compact, remove the three screws on the left side of the compact, rotate the clip to the other side, and restore the screws on the left side of the compact.

2. The toner cartridge counter needs to be cleared

If you are sure that there is powder in the toner cartridge, you need to open the front cover when the printer is turned on, press the "Clear and Return" button, the screen will display "Yes to replace the toner cartridge", press "Yes" on the panel, the screen prompts "Accepted", close the front cover, and enter the ready state after the machine is preheated, and the drum rack will be cleared successfully. If the "Toner Cartridge Error" message is still displayed on the screen, it is recommended to replace the toner cartridge and repeat the above operations.

Difference Between Toner Cartridge and Ink Cartridge:

1. Ink cartridges. Ink cartridge is used to store ink, inkjet form for printing work, it is suitable for some printing color paper**, the most used is small print shops. Ink cartridges have a large storage capacity, but printing is more ink-intensive and expensive.

2. Toner cartridges. Toner cartridges are used as laser printing, compared with ink cartridges, the two printers are not the same for the population, now many large companies will use toner cartridge printers, which are more cost-effective and fast, and the disadvantage is that the toner cartridge has to be replaced with a new one when it runs out.

The printer cartridge error is to compress the printer's toner cartridge.

1. First open the top cover of the printer.

2. Then open the toner cartridge of the printer to fix the lock.

3. After that, you will see the toner cartridge of the printer.

4. Then pull out the toner cartridge of the printer.

5. Then put the toner cartridge of the new printer in the middle position and press it tightly.

6. Finally, cover the printer's toner cartridge fixing lock.

The cartridge appears, and the green slider on the sliding drum unit is the cleaning corona wire.

The charging net and corona wire are dirty, slide the green slider, the slider is actually a sponge block, slide back and forth, and the dust on the corona wire will be cleaned up. If you have strong hands-on ability, you can disassemble the charging fence behind the drum rack, use alcohol cotton, and wipe off the carbon deposit. Corona wire is often dirty, mainly because the powder leaks from the powder cartridge and runs into the corona wire, and the corona wire is oxidized by air humidity.