How to connect the network cable head? How to connect the network cable head

There are two ways to use network cables, one is a crossed line, and the other is a parallel line.

The practice of crossing the line is: one end adopts the 568A standard, and the other end uses the 568B standard parallel line: both ends are the same 568A standard or 568B standard, (generally the practice of 568B parallel lines is used).

568A Standard: Green White, Green, Orange White, Blue, Blue White, Orange, Brown White, Brown 568B Standard: Orange White, Orange, Green White, Blue, Blue White, Green, Brown White, Brown.

You can notice that the difference between the two methods is that the orange and green colors are swapped.

If the two parties to the connection are not equal, use parallel wires, such as a computer connected to a router or switch.

Use crosswires if the two connected devices are equal, such as a PC to a PC.

I hope mine can help you a little.

The above is just a regular connection!

But it's okay for you to have both of them! Because the general network cable is only used in others, even if it is not connected, it can be used! ~

White, orange, orange, white, green, blue, white, blue, green, white, brown, brown.

Do you want to make your own network route? Or use ready-made threads?

If you do it yourself, you also need special tools, if it is ready-made, you need to connect to the host, there are foolproof designs on it, and you can't connect it on the wrong side.

What you want is the sorting of the lines inside the network cable: orange, white, orange, green, white, blue, blue, white, green, brown, white, brown, white, brown.

There are two ways to connect the crystal head of the network cable, one is the cross line, the other is the parallel straight line, and there are different formulas for different connection methods, as follows:

The connection method of the cross line is: one end adopts the 568A standard, and the other end adopts the 568B standard.

The connection method of parallel through line is: both ends are 568A standard or 568B standard.

568A standard: white-green, green, white-orange, blue, white-blue, orange, white-brown, brown.

568b standard: white orange, orange, white-green, blue, white-blue, green, white-brown, brown.

Precautions. 1. If the two parties of the connection are not equal, use a parallel (straight-through) line, such as a computer connected to a router or switch; Use crosswires if the two connected devices are equal, such as a PC to a PC.

2. It is possible to connect the same at the same time, because the general network cable is only used, and the others can be used even if they are not connected.

White, orange, orange, white, green, blue, white, blue, green, white, brown, brown.

The other end is orange and green.

There are dedicated network cable pliers, and you'd better go to the place where you bought the network cable and let them clamp it for you.

1.The same color is joined together, such as orange and orange, orange and white and orange white. 2.

Try to stagger the stranded wire joints, such as cutting this end into a 2 cm long orange line, cutting this end into a 2 cm short orange white line, cutting the other end into a 2 cm short orange white line, and then 2 cm long orange white line, and then on the buttocks of **. 3.Try to keep each pair as long as possible to avoid disconnection due to a pull force that is too short.

4.After the insulation is covered, the two wires can be twisted together and staggered, and only wrapped once. Once all the wires are connected, they should be bandaged with insulating tape.

5.If the cable joint is in the air, be sure to pull some back near the cable joint, wrap it into a loop, and then let the back joint be tied together, and the joint should be avoided from generating excessive tension.

Dear, refer to it.

How to connect the network cable: 1First prepare the necessary tools, insulating tape, scissors, and broken wires; 2.

Use scissors to peel off the outer skin of the broken filament. The length of the peel can reach the peel and after peeling off the outer skin, the 8 inside are separated from the pit; 4.Then peel off the outer skin of the 8 and wire cores to expose the copper core; 5.

After that, the broken network cable is screwed together and connected with the copper core of the same color; 6.After screwing, use insulating tape to wrap the copper core, and then connect and wrap the remaining 7 cores in the same way; 7.When 8 is connected with the core and wound well, then use insulating tape to wrap 8 and the core together, here can be wrapped a little thicker, to avoid the subsequent accidental breakage again, so that the docking is completed.

Dear, this is the step

Dear, if you think my answer is good, you can pay attention, next time if you have any questions, you can click on my avatar for a private consultation, here I promise to answer patiently for you, you can relax!

Dear, if the problem is solved, move your little hands to give a thumbs up, hehe

Detailed interpretation of the connection and sequencing of the joints of commonly used network cables.

1. When connecting the network cable connector, you need to remove two to three centimeters from the outer skin at both ends of the network cable, and sort and close the color of the network cable according to the way of 568b or 568a, and then use the crimping pliers to cut the network cable, and then fix the network cable in the crystal connector, press it with the network cable pliers and insert it into the tester for testing, and determine that there is no problem before use.

2. How to connect the network cable when it is broken, because the network cable is divided into several colors, when the network cable is broken, you can peel off the shell of the network cable, and then connect the wire of the same color, and wrap the insulating tape after connecting each wire, but this connection method is only suitable for use in the case of the middle part of the network cable is disconnected.

3. When the network cable in the crystal connector is broken, you also need to peel off the network cable shell, and then put it into the network cable pliers to rotate it, and then sort the network cable according to the way of 568b or 568a, cut the network cable together, and then fix the network cable in the crystal head, and use the network cable pliers to press it.

4. When the network cable is broken, a section of the network cable with insufficient length can be made into a crystal head, and then connected with the connector, and the other end is connected with another network cable through the crystal head, which is not only low in cost, but also very simple in connection mode.