What are the common faults of Xiaomi instant hot water dispensers?

1. The heating lamp is not lit and not heated.

Cause of failure: (1) Due to the lack of water in the water dispenser during installation, it is caused by dry boiling and power failure.

Solution: Disconnect the power supply, turn on the rear plate, there are 2 thermostats on the side of the hot water tank.

One of them is temperature controlled with a switch to prevent dry burning, with a screwdriver.

Just push the switch inward; After the switch is reset, power on to check, this is the heating indicator light back on, turn off the power, and screw on the rear plate.

Cause of failure: (2) The reset thermostat is not reset.

Exclusion method: (1) Unplug the power plug and cut off the power supply;

2) Wait for the water temperature of the hot tank to drop below 25%, and press the reset button of the thermostat.

2. Water dispenser leakage.

Cause of failure (1) The float valve of the water purifier is not installed correctly, and when the water dispenser is full, the float valve fails to stop the water from flowing down the bucket of the water purifier and causes water leakage.

Exclusion method: Reinstall the float valve and test whether it works normally under the tap before placing it on the water dispenser;

Cause of failure (2) The silicone tube in the Hongrui Hi-Tech water dispenser is loose due to transportation.

Exclusion method: Open the back plate, directly observe or add water to observe which interface leaks, find out, and use the new or original cable to fit the silicone tube on the interface. After repair, use a dry cloth to dry the parts inside the water machine.

3. Water seepage from the tap of the water dispenser.

Cause of failure: (1) Whether the buckle position of the faucet is tightened;

2): Whether the buckle position of the faucet is twisted and rubbed.

Exclusion method: clockwise.

Tighten the red or blue part of the faucet to reset the faucet tightening. Or unscrew it counterclockwise, adjust the silicone tube and spring in the faucet by hand, and then re-screw the faucet; You can also ask after-sales service personnel to come to replace the buckle of the faucet or open the back panel to replace the whole faucet.

4. The cold and hot water of the water dispenser are warmed.

Cause of failure (1) The water level in the base is full of hot water outlets.

Exclusion method: Check whether the float valve of the water purifier is not installed properly.

Cause of failure (2) The water in the water cooler is full and covers the hot water vent on the side of the water dispenser, or the cold and hot water are connected together to cause cross-temperature.

Solution: Reinstall the float valve.

The common factories of Xiaomi instant hot water dispensers are that they do not produce water, and there are some cases where they are not heated. These are relatively simple and easy to solve.

Common faults of Xiaomi hot water dispensers. Xiaomi does not have it, namely a hot water dispenser, I have not seen such a water dispenser.

Summary. Millet instant hot water dispenser, press the child lock, four and so on, no hot water, this function is to play a protective role, to prevent children from being scalded when they accidentally touch the boiling water switch. Press and hold the child lock, the valve will automatically close, and no hot water will be released.

Millet instant hot water dispenser, press the lock of the round child, four and so on, no hot water, this bureau and regret a function is to play a protective role, to prevent children from being scalded when they accidentally touch the boiling water switch. Press and hold the child lock, the valve will automatically close, and the water will not be heated. Kiss. Hello.

This common fault generally has a series of problems such as no hot water, no water, no heating, and so on.

The child lock function light is on, and there is no response when you press and hold.

Is there no hot water now?

No, none of the keys come out of the water.

And the hot water button doesn't move.

Unplug the power supply and plug it back in if there is any response.

1.Press the pants and hold the "child lock" button, after the corresponding lack of pure indicator light flashes, and then press the "smaller" and "larger" keys in order to ensure that each regret button is effective, and it can be unlocked.

It's possible that the heater is broken.

Restart after power failure, the child lock function key is still on.

That could be a broken thermostat, a broken electric heating pipe, or a bad contact or broken wiring.

There are several possibilities.

You don't need it for the time being, find a maintenance master to come to the door to disassemble it, and you will know the specific situation.

Summary. Hello, there are four reasons why the Xiaomi instant hot water dispenser does not produce water:

1.The silicone tube in the water dispenser is twisted and the water does not come out, and it is reset.

2.The new water dispenser faucet does not produce water, and the air is discharged with air resistance.

3.The new button type does not produce water; Bad contact, adjustment.

4.The hot water faucet of the old water dispenser does not produce water, and the main thing is that the check valve is changed to a check valve.

These are the four reasons that come to mind, I hope mine is useful to you.

The reason why the Xiaomi instant hot water dispenser does not produce hot water.

Hello, there are four reasons why the Xiaomi instant hot water dispenser does not produce water:1The twisting of the silicone tube in the water dispenser causes no water and resets.

2.The new water dispenser faucet does not produce water, and the air is discharged with air resistance. 3.

The new button type does not produce water; Bad contact, adjustment. 4.The hot water faucet of the old water dispenser does not produce water, and the main thing is that the check valve is changed to a check valve.

The above are the four reasons I think of Hongsong, I hope my filial piety to you.

The first is to check the fuse, the fuse should be at the back of the water dispenser, it is an insulated plastic head, a screwable protruding part, gently unscrewed in the counterclockwise direction, some water dispensers are to open the back cover to find, if there are symmetrical two on the left and right sides of the stool, it is not the fuse base, it is the drainage pipe when cleaning. The fuse is a separate one, and the color is also different. Go and buy two or three according to this model number for later use.

2. Use a multimeter to measure the resistance of the heating tube. If it's low or zero, it should mean that the heating tube is broken. 3. The connector, that is, the plug part may be in poor contact, or the zero line of the plug is short-circuited, so that there is electricity when you guess the socket, and there should be electricity on both wires.

1. The heating lamp is not lit, and the reason for the failure is not heated: (1) It is caused by the lack of water in the water dispenser during installation. Solution:

Disconnect the power supply, open the back panel, there are 2 thermostats on the side of the hot water tank, one of which is a temperature control with a switch to prevent dry burning, and you can push the switch inward with a screwdriver; After the switch is reset, check the power on, this is the heating indicator light back on, turn off the power, and screw on the rear omen cover. Cause of failure: (2) The reset thermostat is not reset.

Eliminate the square limb method: (1) Unplug the power plug and cut off the power supply. 2) Wait for the water temperature of the hot tank to drop below 25%, and press the reset button of the thermostat.

2. Causes of water dispenser leakage failure (1) The float valve of the water purifier is not installed correctly, and when the water dispenser water tank is full, the float valve fails to stop the water from flowing down the bucket of the water purifier and causes water leakage. Exclusion method: Reinstall the float valve and test whether it works normally under the tap before placing it on the water dispenser;

Cause of failure (2) The silicone tube in the Hongrui Hi-Tech water dispenser is loose due to transportation. Exclusion method: Open the back plate, directly observe the ridge or observe the water leakage at the interface after adding water, find out, and use the new or original cable to cover the silicone tube on the interface.

After repair, use a dry cloth to dry the parts inside the water machine.

Summary. Hello dear<>

Glad for your question Xiaomi instant hot water dispenser does not produce hot water reasons, hello, there are four reasons why the Xiaomi instant hot water dispenser does not produce water:

1.The silicone tube in the water dispenser is twisted and the water does not come out, and it is reset.

2.The new water dispenser faucet does not produce water, and the air is discharged with air resistance.

3.The new button type does not produce water; Bad contact, adjustment.

4.The hot water faucet of the old water dispenser does not produce water, and the main thing is that the check valve is changed to a check valve.

The reason why the Xiaomi instant hot water dispenser does not produce hot water.

Please wait patiently for a few minutes, it is being sorted out, and we will answer you immediately.

Hello dear<>

Glad for your question The reason why the Xiaomi instant hot water dispenser does not produce hot water, hello, there are four reasons why the Xiaomi instant hot water dispenser does not produce water: 1The silicone tube in the water dispenser is twisted and the water does not come out, and it is reset.

2.The new water dispenser faucet does not produce water, and the air is discharged with air resistance. 3.

The new button type does not produce water; Bad contact, adjustment. 4.The old water dispenser hot water faucet does not have Xiangzhu water, mainly the check valve variant is replaced by a check valve.

Banquet orange. Hello dear, <>

If my answer is helpful to you, please give a thumbs up (comment in the lower left corner), look forward to your wide concession and praise, your efforts are very important to me, and your support is also the driving force for my progress. If you feel that I am still satisfied with my answer, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

1.The silicone tube in the water dispenser is twisted and the water does not come out, and it is reset. 2.

The new water dispenser faucet does not produce water, and the air is discharged with air resistance. 3.The new button type does not produce water; Bad contact, adjustment.

4.The hot water faucet of the old water dispenser does not produce water, and the main thing is that the check valve is changed to a check valve.

When the water temperature of the water dispenser is too low, a temperature sensor switch needs to be replaced.

The steps are as follows:1. Disassemble the back cover of the water dispenser and pat the stove. 2. Look for the two electronic components on the boiling water bucket.

3. Replace the first electronic component. 4. Find professionals for maintenance.

Introduction: Water dispensers are mainly divided into three types of warm heat, ice heat, and ice warmness from the function point of view, which will provide different temperatures of water for people to drink, and the machine itself has the function of cooling and cooling, or heating and heat preservation. There are many kinds of ground state types of water dispensers, such as nozzle type, press type, etc.