What is the reason why the suction power of the swimming pool suction machine is too trivial

Are you doing it manually or fully automatically? If it is manual, there are several situations where the suction power may be small:1

Pump problem: The pump is used for a long time, the power is poor, the hair filter is not cleaned, and the pump impeller is wrapped in hair. 2.plumbing problems; The pipeline is not well sealed and there is air leakage.

3.The suction pipe is long, and the resistance of the water is large, which affects the suction power of the water pump. 4.

Suction tray, if you have a large suction tray, and the relative pump is smaller, it will affect the suction effect. It will be more people to feel the suction, but in fact, the suction is not changing. If it is fully automatic, it is mainly a motor problem, and there is also a filter bag or filter paper core that has been cleaned for a long time or needs to be replaced.

I am Shanghai Shengjing Water Treatment Small Money, there is a can be mutual **.

The pump has a low flow rate or is leaking.

The suction power of the sewage suction machine is too small Reason:

1. Pipeline leakage;

2. Assembly accuracy, clearance problems;

3. Running for a long time, the disc is worn;

4. The pump model is small, and the air volume needs to be pumped out.

When the sewage suction machine is working, the water flow is sucked from the bottom of the sewage suction machine and immediately discharged from the upper part of the machine, and there is a filtration system inside the sewage suction machine to filter the dirt.

This depends on the specific situation, either there is a problem with the pump, or there is a problem with the suction head, there is an intention, can help you solve the actual problem.

Summary. It can increase the power of the pump or reduce the accumulation of dirt in the pool.

It can increase the power of the pump or reduce the accumulation of dirt in the pool.

Can you add, I don't quite understand it.

If the power of the pump of the swimming pool suction hole and anti-pollution hall is insufficient, the following ways can be considered: first, check whether the pump body is blocked by foreign objects or the inlet pipe is hypoxic; Secondly, check the connection of the pump and whether it is under the maximum working load, if so, you can switch to a more powerful pump; Finally, a precleaner can be added to filter out more large particles, thus reducing the load on the pump. When overhauling, it is necessary to make good use of tools, and do not use too much force and improper use of tools, so as to avoid causing greater damage to the pump body.

Regarding the sewage suction machine can not absorb water, there are many customers who are busy looking for a sewage suction machine maintenance company without troubleshooting the machine step by step. In fact, this is a very simple question, so [Guangzhou Eurasia Swimming Pool Equipment Company] according to 10 years of experience in the sales and maintenance of sewage suction machines, summarized and sorted out many common operation questions of customers over the years, and the following is carefully analyzed:

Q: Why can't the swimming pool suction machine absorb water? This is a question that many first-time users of swimming pool suction machines will encounter and ask, so why is this happening?

First, we should know what type of sewage suction machine:

First of all, we know that when this shore-based swimming pool suction machine works, the suction pump works on the shore of the pool (which is why it is called shore-based type), and his working principle is that the sewage suction pump is installed on the trolley.

, placed on the shore, through a 15 or 30 meter suction pipe into the bottom of the pool for vacuuming. Therefore, the main reason why the swimming pool sewage suction machine cannot absorb water is to find the reason on the sewage suction pump and sewage suction pipe.

2. Check the joints of the suction pipe.

There are two joints in the suction pipe, one of which can be rotated, and this joint must be connected to the suction head to stretch into the water, so that the suction head can rotate more flexibly when suctioning; The other end that cannot be rotated must be connected to the sewage suction pump.

water spout, so that there is no air leakage. If it is reversed, the rotating joint will leak air, so that the suction pump cannot be emptied when it is working, and the air in the suction pipe cannot be sucked up. At the same time, the suction pipe joint that cannot be rotated.

It must be plugged in tightly to prevent air leakage, otherwise it will not be able to absorb water.

3. Check the sewage suction pump.

If the reason for the suction pipe is ruled out and the water is still not sucked, then it is necessary to check the sewage suction pump, generally to check whether the transparent cover of the sewage suction pump isolator is tightly covered, and the other is to check whether the drain valve under the separator is tightened, if not, it will also lead to air leakage and inability to absorb water.

If these factors are ruled out, the suction machine will be able to absorb water. If this situation occurs in the case of the sewage suction machine that has been used for a long time, and the above factors are also excluded, then please contact your supplier for Changling, which may be that the impeller of the sewage suction pump is blocked, and professional technicians are required to inspect and maintain the sewage suction pump.

Hello! Reasons why the pool suction pump has no suction power:

1. When the suction pump is turned on, see if there is air in the hair collector, and if so, just drain the air.

2. Check if the pump is running normally.

3. Whether the suction port is blocked.

4. Check the circulation system, some designs use a circulating pump to suction dirt, and determine that the circulating return water is closed; If the suction pump is used alone, ensure that the return line of the pump is only connected to the suction port. In addition, only one pump can be used for each suction port.

It only represents a personal opinion, don't spray if you don't like it, thank you.

1. The transformer is overheated; It may be that the working time of the machine is too long or the power of the socket is too large, and the voltage of the sewage suction machine cannot withstand it, which causes the transformer to burn, and many users have a similar situation.

2. Too much garbage in the filter bag: There will be an indicator light on the general machine of the automatic swimming pool suction machine, if the machine does not stop suddenly at the expected time, it is likely to indicate that the filter bag is full of garbage.

Generally, the most common situation is the above two, the best user to use the suction machine before carefully read the instruction manual, all aspects to understand the above situation will not be so nervous.

Our company is specialized in the production of swimming pool sewage suction machine filter bags, you can take a look if necessary, we have sales on Alibaba. Pool suction machine filter bag.

The swimming pool sewage suction machine is mainly used for the bottom and four walls of the swimming pool for sewage suction cleaning, which is mainly divided into: automatic and manual.