There is no heating in the countryside, how can I keep warm?

It's already October, and winter in the north is coming soon, and two days ago, I watched the news and some individual areas in the northeast have begun to snow. In the northern region, there must be heating facilities in winter, otherwise the cold can not stand it at all, and now there is heating or floor heating in the buildings of the cities in the northern region, and some rural areas are also heated, and the problem of heating in winter is not big.

However, there are also some areas where there is no heating in rural areas, such as our home, our home is on the Loess Plateau in Weibei District, Shaanxi, there is no heating in the village, and the following methods are mainly used for heating in winter in our place.

1. Cave heating.

1. Cave heating.

In our area, today's dwelling is still dominated by caves. Everyone knows that the cave is warm in winter and cool in summer. The principle of the cave is warm in winter and cool in summer is that its wall is particularly thick, and the top of the cave is covered with thick loess, which is impervious to the sun in summer, and the heat cannot enter, so it is very cool, and the cold air cannot enter in winter, so it is relatively warm.

2. Stove heating.

2. Stove heating.

Shaanxi is very rich in coal resources, so it is very convenient to buy coal. In our case, many people will build a stove in their room in winter, the fuel is mainly coal, which will not be extinguished all day long, and the stove will continue to spread heat around the room, and the heating effect is very good. The disadvantage is that there is a lot of smoke and dust, and it is polluting to the environment.

3. Ondol for heating.

3. Ondol for heating.

The fire kang heating is the heating method in the Loess Plateau region since ancient times, the fire kang is made of special kang bricks and red bricks, in winter the fire kang is put on the combustible, and then lit, people sleep on it just like sleeping on the electric blanket, the heating effect is also very good, the shortcomings are just like the stove, the smoke and dust are large, and there is pollution to the environment.

3. Electric heater for heating.

3. Electric heater for heating.

The electric heater is light and flexible, as long as there is electricity, it can be used, I bought one last year, ** is not expensive just a few hundred yuan, the heating effect is OK, and clean and pollution-free. The disadvantage is that it consumes too much electricity, and I didn't pay attention to how much power it was when I bought it, but I bought it back and used nearly 300 yuan a month for electricity, which is really a bit irresistible.

The above is the main heating method for us here without heating, and the subject can choose a suitable heating method from here according to his own conditions.

The above is the main heating method for us here without heating, and the subject can choose a suitable heating method from here according to his own conditions.

Although the northern winters are cold. But the countryside is generally lived. Roasted on a charcoal stove with a high temperature after burning. Moreover, in the north, they generally wear thicker clothes in winter, which also plays a role in keeping out the cold.

What is the reason why some radiators are hot and some are not hot.

1. Scope heat outage, first ask the neighbors on the left and right whether the situation is the same, and then find out the reason, determine whether the user's indoor heating facilities are faulty, and then ask the unit or community heating station whether there is a power outage or water outage, whether the heat source or heat station equipment is faulty and whether the heating main network is faulty, and then repair and solve it according to the corresponding situation.

2. The poor quality of the radiator affects the heat dissipation effect, the steam radiator installed in the home of the early central heating user does not meet the requirements of the current water circulation system, and some users buy the radiator to pursue the beauty, ignoring the practicability of the radiator, because these radiators are heated unevenly, the thermal conductivity is poor, and it is easy to cause blockage, affecting the heating effect.

3. The indoor heating part is not hot, and there are generally the following reasons for this situation:

1) Hydraulic imbalance. This situation mostly occurs in a one-cycle installation system in one household, and some radiators are not hot, and the hot ones are turned off and the non-hot ones can be heated up, which is called the hydraulic imbalance of the indoor circulation system. To deal with this situation, the room system can be adjusted to turn off the hot heater first, let the non-hot heater heat up, and then slowly turn on the hot heater.

2) Gas accumulation, blockage or unreasonable installation. If the debugging fails to solve, then the radiator or pipeline may be blocked or seriously installed unreasonable, for the blockage or unreasonable installation, please disassemble and inspect the professional maintenance personnel to eliminate the blockage or reinstall the reasonable installation of the pipeline.

How to deal with rural heating if it is not hot.

First of all, check whether the heating is installed correctly, whether the connecting pipes are connected correctly, and whether the valves are opened correctly. If these are the reasons, the solution is to reconnect the components and open the valves correctly, and if you can't solve the problem yourself, ask a professional installer who installs the heating yourself. Considering that the reason for the heating is not hot, it may also be that the heating is used for a long time, the inner wall is scaled, the thermal resistance increases, and the water flow is not smooth, resulting in the heating is not hot, and the solution at this time is to replace the new heating.

4. The heating facilities are aging, the service life of the radiator in the pipe network is limited, and the user does not maintain it on time, which will cause serious internal corrosion, scaling and blockage, which will affect the heat dissipation effect.

Answer: Hello, the rural radiator is not hot, it may be that the main pipeline valve for heating is not opened, so the valve can be opened in this case. It may also be that the pipeline has not been maintained for too long, resulting in blockage or water leakage, which needs to be repaired by professionals. In addition, if the temperature control valve of the radiator is not opened, and the radiator is not hot, in this case, the temperature control valve can be opened.

1. Generally, the installation of heating is carried out during the decoration, many people are in the summer construction, and the pipeline is often forgotten to install the radiator after the pipe is arranged, because the radiator is not useful in the hot summer. However, when it is necessary to use it in winter, it is very troublesome to carry out secondary construction. Because the heating pipes can be installed when the water and electricity are arranged, and the radiators can be installed when the lamps and lanterns are installed, which is more convenient.

1. There are many cases where the radiator is not hot due to the gas blockage of the radiator, and we need to open the manual exhaust valve on the radiator to discharge the excess gas, and finally make the water flow out of the radiator, and then close the manual exhaust valve. After that, check whether the heating is heating properly.

2. The radiator series itself has a certain partial pressure effect, the farther away from the starting end, the greater the loss in the middle, the smaller the pressure, and the lower the natural heating volume. This situation can be changed to parallel connection, which is separated from the beginning, and the pressure of the parts of their parallel connection is the same, so that the heating is evenly distributed.

3. If there is a problem of radiator circulation, you can increase the circulating pump.

Summary. Hello dear, there are several reasons why the rural heating is not hot: 1. Poor quality of radiators and aging facilities Suggestions:

If the service life is too long, the inner wall is scaled, the thermal resistance increases, and the water flow is not smooth, resulting in the heating is not hot, and the solution is to replace the new heating. 2. The radiator is blocked by gas, and there is gas in the radiator or at the end of the pipeline. Suggested resolution:

Unscrew the exhaust valve at the end of the radiator until there is water in the heater, if there is gas at the end of the pipe, also open the exhaust valve at the end of the pipe to release the air, and then check whether the heating is dissipating heat normally. 3. Hydraulic imbalance mostly occurs in a household and a cycle installation system, and some radiators will not be hot, so the solution is to turn off the hot heating first, let the non-hot heating heat up, and then slowly turn on the hot heating to make it dissipate heat as a whole.

Hello dear, there are several reasons why the rural heating is not hot: 1. The quality of the radiator is poor, and the aging of the facilities is solved: the service life is too long, the inner wall is scaled, the thermal resistance increases, and the water flow is not smooth, resulting in the heating is not hot, and the solution is to replace the new heating.

2. The radiator is blocked by gas, and there is gas in the radiator or at the end of the pipeline. Solution: Unscrew the exhaust valve at the end of the radiator until there is water discharged from the heater, if there is gas at the end of the pipeline, also open the exhaust valve at the end of the pipeline to release the air, and then check whether the heating is dissipating heat normally.

3. Hydraulic imbalance occurs mostly in a household and a cycle installation system, and some radiators will not be hot, so it is recommended to turn off the hot heating first, so that the heating is not hot, and then slowly turn on the hot heating to dissipate heat as a whole.

4. Suggestions for solving poor thermal insulation performance of rural houses: improve the thermal insulation performance of houses and install insulation layers on the exterior walls of housing buildings. Strengthen the closed potato return of doors and windows, it is recommended to add double-glazed windows in cold areas, and the door of the living room can be made into two homes if possible.

Keep warm and increase the temperature! 5. Rural houses with relatively high floor height and low density Suggestions: For houses with higher floor heights, it is recommended to increase the ceiling floor, low-density houses, and increase the surplus of heating equipment, including wall-hung boilers, pipelines, radiators, etc., so that when can the effect be good and warmer in the winter when the hand-code heating is sold.

Rural heating options can be chosen according to local climate, fuel resources and economic conditions. Here are a few common ways to heat your countryside:

1.Coal-fired heating: This is a common heating method in rural areas, with abundant coal resources and good combustion effect. However, burning coal produces large amounts of carbon dioxide and harmful gases, which are harmful to the environment and health.

2.Biomass heating: Biomass energy includes firewood, straw, wood chips, hemp stalks, etc., which is a more environmentally friendly heating method. However, the instability of biomass energy, the high cost of storage and transportation, and the need for certain technical and management experience.

3.Solar heating: Solar water heaters are a green, renewable way to heat in sunny areas. However, the installation and maintenance costs are high, and the technical and management experience needs to be approved in one fell swoop.

4.Electric heating: The use of electric heating can avoid the harmful gases and particulate matter produced by fuel combustion, and it is also more convenient. However, the high cost of electricity may be more difficult for rural households with more difficult economic conditions.

When choosing a heating method, you need to comprehensively consider local climatic conditions, energy**, economic conditions and other factors to choose a most suitable heating method for yourself. At the same time, it is also necessary to pay attention to safety and environmental protection, and reduce environmental pollution and health hazards.

Radiator villa heating radiator is the use of air hot and cold circulation, in the indoor space to achieve a local convection, more suitable for use in a small area of the room, replaced by villas are not suitable. Due to the larger space of the villa, there are more cold walls, and the floor-to-ceiling bay windows are larger, so the amount of heat dissipation required is also larger. In order to achieve a comfortable indoor temperature, it is necessary to increase the number of radiators, which not only occupy space area, but also waste gas, and the most important thing is that there is a problem of smoked walls in the heating.

Most of them are solved by radiators, and some places will use stoves for better heating.

Many rural areas are now equipped with uniform methane heating equipment. Some villages have also been warmed to help farmers better survive the cold winters.

1. Check the fuel type: the heating of the stove may not be hot because the fuel type is wrong, and you can change the fuel in the manuscript; 2. Check the flame: if the heating of the stove is not hot, the flame may not be large enough, and the size of the flame can be adjusted to adjust the temperature of the heating of the stove; 3. Check the smoke pipe:

If the heating of the stove is not hot, it may be that the smoke pipe is blocked by the tease and needs to be cleaned; 4. Check the ventilation: the heating of the furnace is not hot, which may be due to insufficient ventilation, and you can consider increasing the ventilation volume of the ventilation shed; 5. Check the stove: If the heating of the stove is not hot, it may be that there is a problem with the stove, and you can consider replacing it with a new one.

1.Check that the burner is adjusted correctly, and if not, readjust it. 2.

Check the burner for dust accumulation, and if so, clean it up in time. 3.Check whether there is insufficient flame when the furnace is burning, and if so, adjust it in time.

4.Check the pipes of the stove for stagnant water, and if so, pull it out in time. 5.

Check whether the indoor temperature setting of the stove is correct, if not, please adjust the finger posture. 6.Check that the hot water pipe of the furnace is installed correctly, and if not, reinstall it.

7.Check whether the water level of the furnace is correct, if not, adjust it in time. 8.

Check the furnace body of the furnace for water leakage, and if so, repair it in time.