If you want to do tile seams and want to save some money to do it yourself, what should you pay atte

Before the tile seam, the key to the preparation is the seam. Hot melt gun. Sewing knives.

Paper cutters. Car wax. Masking tape, etc.

Generally, in the process of purchasing sewing agents, you can buy a complete set, and the price will not be expensive. Once you're ready for this, you can gradually put it into practice.

1.Seam cleaning. How to do the beautiful seam, the first step is very important, the tile gap is not clean, and the tile seam is busy. Before the seam is cleaned, the most important tile gap can not store water, too much moisture will cause the beauty of the joint agent to fade.

First, use a caulking knife or utility knife to loosen the concrete and dust in the tile gap so that it can stick to the edge of the tile, (be careful not to break the corners of the tile) and then use a brush or vacuum cleaner to remove the dust inside.

2.Polishing and waxing.

In the past, there was a process of making tile beauty sewing that was pasted with masking glue, but now it is not used. Tiles can also be used to prevent smooth and clean at the same time. Antique tiles, or to prevent uneven tiles must be polished and waxed, polished and waxed on both sides of the tile gap, no need to be too much, pay attention not to leak, to prevent inconvenience in the middle and later processing.

3.Glue. Cut the mouth of the glue nozzle at 45 degrees, which is a little smaller than the tile joint.

Then the front 30 cm up and down beaten out without use (this section of the sewing agent is not very well mixed, not easy to condense in the middle and late stages) and then evenly hit in the tile joint, it is best to do it yourself is a little more, do not have to float on the top layer, the bottom is empty.

4.Seams. In the actual operation in summer, the sewing agent dries quickly, and if you are not skilled, you can gradually press the seam after half a stick.

There are many customers who do not understand the beauty sewing agent at the beginning, and there are too many beauty sewing agents at one time, and it will condense in a hurry to solve the problem, and it is very troublesome to scrape the seam after condensation. The joint can be pressed with a ball or tungsten steel rod, pay attention to the four tiles cross the area to check the strength, to avoid the dent of the sewing agent.

5.Remove glue stains.

The beauty sewing agent has been beaten, and it can be removed the next day, and it can be eliminated with a gray knife.

Pay attention to the technology of beauty sewing, pay attention to the selection of products, pay attention to the skills of beauty sewing, ensure smoothness, pay attention to the width, and pay attention to the construction situation.

When choosing the color of the seam, it is necessary to match it according to the color of the tile, choose a similar color, of course, you can also choose the opposite color, mainly depending on personal preference, for example, beige with ivory gold seam, the whole beauty seam effect is very good, and the ivory gold seam color is low-key luxury and connotation.

Clean the tile gaps Sanitation Use relevant tools to clean up the dirt in the tile gaps, if there is a vacuum cleaner at home, you can also use it to wash the cement dust, be sure to ensure that each tile gap is clean, without a little dust.

During the construction of the sewing glue and pressing the seam, we must pay attention to the uniform force, otherwise it will make the sewing agent pile up in some places and not in some places; And it is best to pass it once when pressing the seam, so that the beautiful seam that is pressed out is beautiful, because if the repeated seam is not done well, it is easy to appear interface, which affects the appearance.

I think you can buy some tile sewing agent online, you must pay attention to the problem of cost performance, choose some cost-effective sewing agent, and then do it yourself.

You must be extra careful when filling the sewing at home, although you are a layman, but the slow filling can also achieve the effect of the sewing master. In fact, filling and sewing itself is a relatively simple job, which can be completed in 1 or 2 days at home, and can also save two or three thousand yuan.

Of course not. If you operate it yourself, you can buy some epoxy color sand sewing agent, choose the right color, and then squeeze the glue on the toilet paper in advance before gluing, and then operate, during the operation, you should put glue in the gap, and then flatten both sides, and after drying, just pull the glue up.

The tile is not bad, the master does not necessarily have to do it for the master, he can also operate, as long as you buy the color you like, clean the tile very clean, and then follow the tile seam these smearing, and then leveling, the effect is also very good.

No. If you do it yourself, you must buy a good quality sewing agent, and then you should also prepare professional tools, you need to prepare a shovel, and then squeeze these sewing agents into some brick joints, and then use a shovel to smooth it, and be sure to maintain the overall flatness.

Tile beauty seam is to stop beautifying the gaps of ceramic tiles. Generally speaking, we need to use "caulk" to make tile joints. And our caulk, in fact, has experienced several developments, from white cement, to grout, to beauty sewing agent, porcelain caulk, epoxy color sand.

Clause. First, the tile air care is more convenient. We all know that the tile gaps are particularly easy to hide dust, and the air is particularly dirty after a long time, and the tile gaps are particularly difficult to liquidate, which is a headache. White cement joints, cheap cost, high hardness, not easy to scatter, but during the construction of the need to pay attention to maintenance, if it is used for air gaps, it will appear after mopping the gap blackening, the reason is that after the mop is dirty, the sewage will pollute the white cement, forming a blackened gap.

Clause. Second, it increases the overall aesthetics of the house. There are a lot of styles to choose from, the color is gorgeous, and the whole space feels higher after the perfect sewing, but it will not cost a lot of money, and most local families can afford it, even if they start with it. Caulk caulk, the cost is relatively cheap, the common colors are white, yellow, used in the wall is complete, but the demand to ensure that the environment is boring, wet state is easy to nitrate, used in the air will show the gap blackening, scattered phenomenon, the same will also present the problem of blackening the gap when mopping, especially in the bathroom and other common water areas, will become more and more obvious, and it is easy to hide dirt after a long time.

Clause. Third, the aerial structure of ceramic tiles is more stable. Ordinary friends who have tiled at home know that the tiles will loosen and warp after a long time, which is very disturbing. The adhesive has excellent adhesive performance, which can make the structure of the tile in the air more stable, and it is not easy to show the condition of tile lifting.

The beauty of the sewing agent, the color of various styles are available, the cost is related to the first two is relatively high, for the wall and the air are able, adhere to the years are also relatively long, the later good maintenance, liquidation and sanitation are also relatively simple, in recent years has begun to prevail, and has been liked by the majority of customers.

The sewing agent can make the home look more beautiful at a great level, and at the same time, it can play a role in maintaining the tiles! The most important point is that the tiles have been used for a long time, and it is easy to show hollow or scattered conditions, and if you can use the beauty of the seam this kind of information well, then we do not need to worry about the use of tiles, this kind of thing.

Should. This not only makes the overall appearance of the floor more aesthetically pleasing, but also prevents the tiles from protruding.

Yes, because seams prevent water from leaking to the floor, extend the life of the tiles, and look clean and tidy at the same time.

Nowadays, people will choose to do tile seams after decoration, and I personally think that it is not necessary, because after a long time, it will become black if it is not, which will affect the aesthetic effect.

It is necessary. Generally speaking, it is proposed that the tile seam should be at home, especially after the construction of the project, when the furniture does not enter the home, but at this moment, we need to pay attention to the smoke and dust in the house that has just been constructed, and it is necessary to pay attention to the gradual tile seam after cleaning, otherwise it will not be beautiful. In fact, the effect of tile beauty line in a family to find there is very great, he can not only prevent moisture, mildew, blackening, and do the ultimate seam after the aura of the new house is different, beautiful and generous.

The tiles must be made of beautiful seams.

1.Advantages of ceramic tile joints: smooth surface such as porcelain, beautiful, wear-resistant, easy to clean, waterproof, time-saving and labor-saving, healthy, can effectively reduce the black and yellow of tiles.

2.Disadvantages of ceramic tile seams: There are basically no shortcomings in ceramic tile seams, as long as the early seam master handles it well, it will not fall off.

3.If you use the beauty sewing agent to make the tile seam, it is very atmospheric, and the tile at home uses it to sew the tile, the tile is not afraid of cracks, and can protect the tile to a certain extent.

Extended: It has a smooth surface, easy to scrub, easy to clean, waterproof and moisture-proof, which can avoid mold breeding in the crevices and endangering human health. We no longer have to hesitate between the pursuit of beauty and health, because with beauty joint, we can choose our favorite tiles that can reflect the personality, and we no longer have to worry about the harm caused by mold growing in the crevices.

Of course, it is necessary, you need to choose a beautiful sewing agent with a good waterproof effect, so that you can use it better, you can choose the cake piping bag, the operation through this kind of thing is very simple, and the effect is very good.

It is necessary to do it, do not do beautiful seams, after a long time, the tile gaps will become moldy and black, breeding bacteria. This problem can be solved well after making a beautiful sewing agent, and it is easy to clean, and the temperament of the house after doing the perfect sewing is different and beautiful.

Pressing and scraping: If you want the surface of the colloid to have a moderate arc surface of each tank after curing, you can use a special steel ball to pull along the brick joint to the other end from one end to keep it even; If you want to make the colloidal water cured and the tile surface as much as possible, after installing the sewing agent into the glue gun, we need to squeeze out the first 40cm of the sewing agent, because the uneven mixing of the sewing agent in this section may affect the later effect. Once you've put the paper on, it's time to start caulking!

The hose glue gun is ready, and when caulking, it is necessary to pay attention to the strength, one down, and the whole strength should be consistent, so as to avoid squeezing out a lot at a time and squeezing out very little.

At present, there are many domestic brands of sewing agent, and there are many counterfeit ones, I suggest that you go to the regular supermarket to buy, or call the personnel of professional caulk to help deal with it, that is to say, buy the material yourself, please use a scraper to scrape off the excess sewing agent after the professional caulk is finished. When the sewing agent is dry, tear off the paper on both sides. Then use a small rag to wipe the soiled tiles around.

Cleaning is quite a tedious process, and there is a lot of dust that can get stuck in the crevices of the tiles when decorating, so be sure to be careful and careful. You can sweep it away with a brush while using a scraper to avoid staining the cleaned gaps. You don't have to work too hard when cleaning, as long as most of the owners use the latest epoxy resin caulk tile sewing technology, in a humid and hot environment, it still has a good anti-corrosion and anti-mildew effect, and the high-quality sewing agent will not change color for 20 years.

The construction techniques are not in place. The factors that cause the bubbles are certainly not one-sided, in addition to the quality of the glue, the master's technique is also very important. For example, when feeding, the outlet of the mixing nozzle is cut too large, the gap is not completely covered when the material is pressed, and the air is repaired with the least amount of air.

Since the sewing is manual construction, it is inevitable that there will be some defects, therefore, the sewing master should be fully inspected after completion, and the flaws should be repaired, not only to ensure the aesthetics, but more importantly, not to let the flaws become hidden dangers.

Step 1: Prepare the construction tools.

Step 2: Use a slotter Flat screwdriver Grout knife to clean up the dust and garbage in the tile gapsStep 3: After the gaps are cleaned, unscrew the pipe cap and install the mixing tube, and the tube head is stuck on the bayonet of the glue gunStep 4:

After installing the mixer, cut a 45-degree angle with a utility knife from below, remember that the opening should be smaller than the tile gap, if the tile gap itself is relatively small, you can not cut the nozzle.

Step 5: First punch out 30-40cm of the remaining material of the sewing agent, and then start the construction along the gap of the tile, and the caulk must fill the gap of the tile during construction, otherwise it may collapse in the future.

To do your own tile seam, you must first remove the impurities in the tile joint, and then carry out the seam. When beautifying the seams, we must pay attention to uniformity to prevent uneven gaps, and the edges of the seams need to be trimmed after the sewing is completed.

When we decorate the house, most of them will choose to pave tiles when decorating the ground, but there will always be seams after the tiles are paved, not only not easy to clean, but also not very beautiful, so at this time, there will be a partner to choose to give the tile seam, because the tile will appear more smooth after the seam, and make the tile look more smooth. So in the endTile should not be made of beautiful seamsLet's introduce it to you!

First, should the tiles be made beautiful seams?

1.Tile seam is a combination of art and home decoration, which can not only enhance the overall visual beauty of home decoration, but also highlight your quality of life and status, so that you have more face. The tiles are not beautiful, and after a long time, the cracks begin to be gray, and the heavier ones have more peculiar smells floating out, and bacteria are overflowing, which poses a serious threat to the health of the family.

Tile seam avoids the problem.

2.There is no mandatory standard for whether the floor tiles and wall tiles must be seamed, but because of the special environment of the kitchen and bathroom, there are many oil stains and stains, if you do not go to the seams, the walls and the ground of the house will appear yellow, and the longer the time, the deeper the oil stains will soak in, and become black, which seriously affects the beauty of the house. It also produces a large number of bacteria, especially in the summer season, which will affect people's life safety.

Therefore, it is still recommended to carry out beauty sewing treatment.

3.It is not easy to accumulate Zen ash. Before you want to do beautiful seams for the decoration of your family living room, let's first understand what is a beautiful seam for ceramic tiles.

The so-called tile beauty joint is to reprocess the gap between the tiles and the tiles. In the normal decoration situation, there will be a gap between the tiles and the tiles, although this gap does not look big, but after a long time, it is easy to hide a lot of dust, not easy to clean, so many people think of the beautiful seam.

Second, how to make beautiful seams for ceramic tiles.

1.Leave a gap 1 mm deep. Before applying the sewing agent, use a rag or a fine brush to clean up the dust and other magazines in the seam.

Paste masking paper on both sides of the sew. The masking paper should be left and right from the edge of the gap. Install the sewing agent on the glue gun lead fiber spring, and drive it evenly along the brick joint.

The construction is about 1 meter, and it is immediately applied evenly with fingers or a small spatula; When the sewing agent has not solidified (about 1 meter of construction), remove the masking paper with your hands.

2.Load the sewing agent into the glue gun, and then slowly and forcefully beat the material evenly into the seam, after laying a piece (about meters), first plug the nozzle with a wooden wedge, and then use a small scraper or fingers to scrape the sewing agent immediately, the overflowing material on both sides of the brick joint can be wiped off with a moist sponge, and it must be wiped clean before the sewing agent is not solidified. Wash the sponge with water after each wipe so that you can continue to use it for the rest of the day.

If the seam width is more than 3mm, and the seam filled into the tile joint is relatively uniform, then there is no need to scrape the seam agent to make it level automatically.

Well, the above is a brief introduction to whether the tile should be made and how to make the tile seam, so after you read the article, do you know how to make the tile seam?