When doing beauty sewing, why do sundries bubbles frequently appear in the beauty sewing agent? How

It may be that there is moisture in the gap, there is ash, the glue is too fast or too thin, or it may be the quality of the sewing agent, etc. In the case of bubbles, you can talk about the bubbles bursting, and then talk about the beauty of the sewing agent to fill and flatten.

It is necessary to add chemical reagents to the sewing glue and clean up the debris on the floor, which will be more lubricating.

The sewing agent is a very critical house, after the decoration must be done in time, if the sewing agent appears sundries and bubbles, you should replace the sewing agent as soon as possible.

Tile seam is an indispensable step in decoration, although it looks not difficult, easy to work, but it is really very particular to do! Some owners will build their own in order to save money, and for inexperienced people, they will definitely encounter a lot of problems when sewing, such as: during construction, it is found that there is blistering in the sewing.

I don't want to hide it from you, I have encountered such a situation when I sewed my new house before, and I also consulted a professional sewing master for this. After a little understanding, I learned that the blistering of this beautiful sewing was caused by these reasons!

Causes of blistering.

The gaps were not cleared properly.

Cleaning the gap can be said to be the most difficult process in the beauty of the seam, only by cleaning it in the early stage, can we avoid various problems in the later stage. If you don't clean it well, you will do beautiful seams, and the dust will pollute the colloidal body and occupy the gap space, and it will become uneven, and the blistering will definitely not be able to escape.

In addition, the gap should also be kept dry, if the gap is wet when the sewing agent is applied, the water will evaporate in the later stage, and it will not dry and bulge.

The construction techniques are not in place.

In addition to the gaps are not dealt with well, the construction method is also an important point! For example, the speed of gluing is too fast, the force is uneven, the glue is applied at intervals, and the material is not completely covered when the seam is pressed, which will lead to air in the gap and blistering.

The quality of the sewing agent is poor.

The quality requirements of the sewing agent should be the most basic, even if there is no problem in construction, the quality of the sewing agent used is poor, and there will be blistering after solidification in the later stage.

Solution: Remove the blistered seams and carry out a second seam.

First, use a small spatula to remove the blistered part of the seam (if it is more difficult to remove, you can use a hot air blower to blow the sewing agent soft and slowly remove it); Next, the crevices are cleaned and kept dry; Finally, a second sewing is performed, and the operation steps are the same as before.

Although it is not difficult to solve the blistering of the beautiful sewing, in order to avoid these unnecessary troubles, we still have to pay more attention in the early stage. Clean up the gaps, the construction techniques are in place, choose the best sewing agent, if you can't do the fine work, it is better to find a professional master!

If a small area blisters after construction, you need to see if the tiles are cleaned. If it is not cleaned up, some bumps can be clearly seen in the brick joints after construction.

If it's a large area of blistering, there are two reasons –1. After the construction of the sewing agent is completed, it should be exposed to water (destroy the balance) without being completely dried or let the sewing agent be exposed to air for a long time before construction;

2. The product quality is too poor, and the black-hearted merchants use inferior materials.

The beauty joint agent is an upgraded version of the traditional grout, which can solve the problem of dirty and black tile joints, and is very popular in home decoration, but it often blisters after using the beauty joint.

The cause of foaming of the sewing agent.

1. The tile gap is damp, the tile adhesive layer is not completely dry, and the water vapor at the bottom evaporates to produce bubbles;

2. The dust and impurities in the tile gaps are not cleaned, and the rubber surface is uneven and blistered after the seam;

3. After the construction is completed, the joint is pressed back and forth repeatedly, which will lead to the introduction of air and the phenomenon of bubbles or bulging;

4. The thickness of the sewing construction is not enough, which is not enough to compact the air inside the pants, and it is also prone to bubbles;

5. The heating temperature of the sewing agent is too high during winter construction, resulting in blistering during construction;

6. The quality of the sewing products is poor, and the colloid is mixed with a lot of gas during the production process, resulting in blistering during construction.

Repair tips for beauty sewing agents.

1. Temperature. The indoor temperature --- 5 or higher.

The temperature is low in winter, and the curing speed of the sewing agent slows down after construction, so it is necessary to avoid the curing process temperature being lower than 5, otherwise, there will be embrittlement (brittleness of the rubber strip) during cleaning.

Product heating - 50

When the indoor temperature is lower than 5 in winter, the sewing agent can be put into a special heating bag or hot water for preheating in a closed state before construction, the preheating temperature should not exceed 50 (boiling water must not be used), preheating for 10-15 minutes, when the water bucket is warmed and preheated, the discharge port of the sewing agent should be facing down, the bottom is facing up, and the water should not exceed the bottom.

Construction under underfloor heating conditions --- avoid local high temperatures.

In the construction under the condition of floor heating, the temperature in the local area is too high, and the construction process is easy to produce bubbles. Turn off the heating and wait for the temperature to drop before construction.

2. Humidity. The construction of the beauty sewing agent requires that the gap environment should be dry and dust-free, the temperature difference between indoor and outdoor in the north is large, and the construction of doors and windows should pay attention to avoid moisture; There is a lot of humidity and fog indoors in the south, so it is necessary to keep the indoor environment dry.

3. Incision. During winter construction, for large-particle toner sewing products (noble gold, noble silver, etc.), the incision of the glue nozzle should be larger (but not the largest), and the base sock bend can ensure the uniformity of the toner and colloid.

4. Ventilation is prohibited.

In winter, the wind in the north is cooler, and the low temperature is easy to crack and shrink in the process of solidification, while the wind in the south carries water vapor, and the window is easy to absorb moisture and turn white, and the color becomes lighter. It is recommended to close the doors and windows before the construction of the sewing agent, and turn on the heating or heater at the same time to increase the temperature and fatigue of the room.

If the foaming phenomenon occurs in the use of sewing agent in home decoration, you can find the reason from the above content, and at the same time, it is necessary to maintain the sewing agent well in order to prolong the life of the sewing agent. Hope the above is helpful to you.

The bubbles are usually caused by the following reasons:1Mixing is not uniform:

When mixing the sewing agent, if the mixing is not uniform, excess moisture may appear in some areas, resulting in bubbles during the construction process. 2.Construction Environmental Issues:

For example, when the temperature of the construction environment is too high or the sun is exposed, the surface of the sewing agent is easy to dry quickly, and it is difficult to completely fill the gap. At this point, when the fresh sewing agent enters the gap and is subjected to atmospheric pressure, bubbles will form. 3.

Expiration of sewing agent: The shelf life of sewing agent is limited, and if it is used after expiration, it is easy to carry cherry blossoms. In order to avoid this problem, we can take the following measures:

1.Before using the sewing agent, stir it thoroughly; 2.Treat the gaps before construction to ensure that the surface is clean and dust-free, so that the seam agent can fill the gaps more fully; 3.

Be sure to choose a good quality sewing agent, pay attention to its shelf life, and do not use expired sewing agents; 4.Avoid harsh environments such as high temperature and strong wind during construction. In short, in order to ensure that the beauty seam effect is good, it is necessary to inspect and prepare the materials before construction, and strictly follow the relevant regulations and operation procedures.

If there is a bubble problem, deal with it in time or re-apply it to achieve the desired effect. Pro-<>