How long does it take for JJUMI sewing agent to cure?

Under normal circumstances, the sewing agent is dried in 3-6 hours, cured in 12 hours, cured thoroughly in 24 hours, and can be used normally after 48 hours.

If the enamel on the surface of the sewing agent is not completely dry or in a sticky situation, it will have a chemical reaction when it encounters water or moisture, and the enamel on the surface of the product will turn white.

Especially for the beauty joint agent of the floor tiles, the construction personnel will not fill the beauty joint agent, and it will collapse if you wipe it hard. Manufacturers' formulas and materials are different. The curing time is also different. (25) at room temperature. Some manufacturers are solidified.

In this way, under normal circumstances, Qingjumei sewing agent is dried in 3-6 hours, cured in 12 hours, cured thoroughly in 24 hours, and can be used normally after 48 hours.

1. First of all, spray an appropriate amount of glue remover on the cured sewing agent, and pay attention to make the glue remover completely cover the cured sewing agent.

2. Then you need to wait patiently for about ten minutes, the glue remover contains a certain amount of organic solvent, which can remove the cured sewing agent solvent.

3. After the cured sewing agent solvent below, wipe it clean with a rag.

4. Finally, take a look at the effect after removal, and you can see that the cured sewing agent is completely and completely removed.

Generally, it can be washed off directly with a certain concentration of alcohol, and if it has been solidified, it can be soaked in hot water for a period of time and then washed off with alcohol;

2.Soak the stain with shampoo, then dilute the white vinegar with water, and gently scrub with a brush dipped in the solution. After drying, bounce off the dust and rinse it with clean water several times.

1.On the hands and body: **After the sewing agent is cured, it can be soaked in water for 30 minutes, and then wiped with concentrated alcohol or vinegar. If you really can't remove it, you can use sandpaper to rub it slowly and wait for the metabolism to fall off by itself.

2.Clothes and other fabrics: It is difficult to clean up the sewing agent on the clothes, or wipe it with banana water, but this is very corrosive to the clothes. It can be sent to the laundry for professional cleaning, but it is not recommended for ordinary clothes.

3.Tile floor: For tiles with a relatively smooth surface, you can directly use a shovel to remove the cured grout. If it is a tile with a rough surface, you can blow it with a heat gun and wipe it off with a damp towel, or buy an epoxy degum debilitant to clean it.

4.Furniture and wood: If there is a lot of cured sewing agent, you need to blow the sewing agent with a heat gun, then wipe the excess sewing on the surface, spray epoxy resin detangler on the wood, and then scrub carefully.

The main thing is the temperature, generally speaking, 3 to 4 hours at room temperature can be cured, some curing is faster, such as Baoshijie, as long as two hours can be dry, when the temperature is higher, the curing time will be shortened, so the air conditioner can be turned on to increase the temperature during construction, shorten the curing time.

I'm glad for your question, dear, according to the inquiry, can the sewing agent be cured without a curing agent, the answer is no, the raw material of the sewing agent contains epoxy resin, which determines that it can't withstand high temperatures. If it is exposed to direct sunlight or stuffy in a car with a relatively high temperature, it will have the problem of poor stickiness. In addition, the sewing agent is a double group, resulting in an uncoordinated mixing ratio between the two groups, and the curing will be incomplete.

1. First of all, prepare a bottle of real rubber remover and spray it evenly on the stains after the sewing agent has cured.

2. When spraying, the adhesive remover should cover the entire stain surface.

3. Then apply evenly with your hands and let it stand for about 20 minutes.

4. Next, use a rag to wipe it, and wipe it vigorously several times.

5. At this time, you can find that the stains of the sewing agent are gradually wiped off.

The remaining materials on both sides are shoveled down with a shovel, if you are a fully glazed brick, you can use this method, but if you are a rough brick, paste it with masking paper for construction, and the rough brick is uneven and it is not easy to clean up with a beautiful grout.

It is possible to purchase a special sewing agent cleaner. Cleaning agent is a special product used to clean the residue of the joint on the surface of the tile after the construction of the tile joint. The appearance of colorless and transparent liquid, slightly ammonia smell, can quickly clean all kinds of seams, paints, asphalt, adhesives, adhesive paper, tape residues, lipstick marks, soot and other residual stains on the surface of ceramic tiles and stones.

Hopefully, the above can help you.

1. For the first time, prepare a bottle of real rubber remover to evenly spray the stain after the sewing agent has cured.

2. When spraying, the adhesive remover should cover the entire stain surface.

3. Then apply evenly with your hands and let it stand for about 20 minutes.

4. Next, you can wipe it with a rag, and wipe it hard to wipe it several times.

5. At this time, you can find that the stains of the sewing agent are gradually wiped off.

How to remove the sewing agent stuck to the glass? Method 1: Dip the rag in detergent, or industrial alcohol, or high-concentration wine, and wipe it repeatedly on the glass with beauty sewing agent, and slowly remove it.

Method 2: Use the strong hot air of a hair dryer to blow on the cured sewing agent, soften it, and then wipe it off little by little with a sponge or rag. Method 3:

Dip a cloth in vinegar and cover it with a knife to remove it slowly when it is completely soaked.

How to remove the sewing agent stuck to the clothes?

Method 1: After the sewing agent is removed, be sure to wash your hands and clothes repeatedly with water, because the smell of ethyl acetate is very strong and will remain on the clothes.

Method 2: Use the hot air of a hair dryer to soften it to the point where it can be torn off, and then clean the remaining imprints.

How to remove the beauty seam adhesive to the rough surface of the tile? Method 1: Use the hot air of a hair dryer to blow on the sewing agent, soften it, and then wipe it off little by little with a sponge or rag.

Note: In this case, it is not recommended to use a shovel to remove, and uneven tiles are easy to scratch the tiles when shoveling. Method 2:

There is a special sewing agent cleaner on the Internet, which can quickly decompose the sewing agent.