The water pumped from my well is always fine and muddy, what s going on? How to fix it?

The water pumped from the well is always fine, and the sand is very muddy, which can be caused by a variety of reasons. Here are some possible workarounds:

1.Laying a layer of clean, fine sand at the bottom of the well, followed by a layer of larger pebbles, helps to filter out impurities from the water.

2.A sand remover is installed at the wellhead to filter the fine sand in the water.

3.Clean the sand from the well regularly, using tools such as a vacuum cleaner or submersible pump.

4.A connecting pipe with a strainer is installed at the wellhead to filter impurities from the water.

5.The use of perforations and then wire mesh wrapping in the water intake pipes helps prevent impurities from entering the water.

6.Settle the sand in the cistern and clean it regularly.

7.Consider re-drilling a deep well for cleaner water.

It should be noted that solving the problem of turbidity in the well requires the selection of the appropriate solution according to the specific situation. If you can't solve it on your own, you can consult a professional water treatment engineer or a well cleaning service company.

If the water pumped out of the well has fine sand and is very muddy, it means that your water has not been used for a long time, or it will only appear when the water is shallow, you can pump the well a few meters down and put alum in the water.

Pump water after one day of precipitation.

The water pumped from the well has fine sand, and the water is also very turbid, which is the sediment in the well, and the sediment needs to be dug out to solve the problem of turbidity.

The water pumped from my well is always fine and muddy, what's going on? How to fix it? There must be sand underneath your house, so the water pumped up has fine sand, and the solution is to continue digging wells deep to avoid the sand layer.

The water pumped from my well is always fine and muddy, what's going on? How to fix it? That proves that there is no filtered thing in your well, that is to say, at the bottom of the well, there are no big pebbles, and when the filtered large sand grains are gone, so the air sprinklers will be pumped up when the water is pumped, which is very turbid and cannot be precipitated, which is what it means.

You can install a filter screen to filter the water, because there is a filter element in the filter screen, so it will be much better after secondary filtration, otherwise it is really difficult to drink fine sand in drinking water, and it is also harmful to health.

This indicates that the geological conditions underneath are not suitable for drilling underground drinking water wells. In some places, the groundwater is not sandwiched by rock formations, which is called a sandy bottom. If you want to change the situation, you can only try it again in another place, and if it doesn't work, filter it before using it.

The water pumped from your well is always muddy with fine sand, and your well is in the quicksand layer, so you can re-dig it deeper or precipitate before using the water.

Hello, generally speaking, as long as the pump is moved up about 50 cm, if it is still turbid, it may be that the well water is not good, and it may be that the surface of the ground has infiltrated water.

This shows that the groundwater environment has changed, and this is not going away, and it is better to re-drill a well.

The water pumped from your well is always muddy with fine sand. This must be the place where the bottom of the sieve under the well of your house is exposed. Hence the sand and muddy objects.

This may be because the soil quality in the well you dug is different, so there is such a situation

Dear, hello, I'm glad to answer for you, my own well has been replaced with a pump, and the water pumped out is particularly turbid, yellow, and muddy, what's going on? Answer: This phenomenon is very normal, the reason is that in the well, the sediment deposit and the original pump form a relative balance, the water pumped out is relatively clear, when the pump is changed, the sediment is loose, the water quality is turbid, and then the pump is a little bottom, resulting in turbidity and yellow sediment.

This phenomenon is very easy to solve, and on the switch to let the pump run for a period of time, the water in the well is pumped out, the water quality will be improved, if it is still yellow, there is a chance to slip the sediment, and the next day to pump out the water, there should be no problem, the water quality will become better, if not, pump a few more times, the problem will be solved! Drain the water and wash the well. If you don't want to do this, the sediment can sink wide, but not "**", and the water will soon become turbid.

Hope the advice is useful to you.

Summary. Hello dear, the water in the well at home is very muddy when it is first pumped out! After a while, the reason became clear:

Water contains a relatively large amount of iron ions. In the well, because it is very deep, there is a lack of oxygen, it is in the form of ferrous ions, it is light green, you can't see it. When pumped up, a large area is exposed to outside air, and it is oxidized to ferric iron, that is, ferric oxide, and rust, which turns yellow.

This situation should be specifically analyzed, if the yellow is bad, the iron content is excessive, or not good, you need to consider the water purifier filtration. If it's not obvious, it's not a big problem, but it's better to use fresh: because the human body absorbs iron, it is absorbed in the ionic form of divalent ferrous iron, and for trivalent rust, it is still harmful to absorb too much.

At first, the pump bottoms out, and after a while, the pump pumps out the surrounding sediment and the water clears. After stopping, the pump bottomed out again, so it was still muddy water pumped up.

The water in the well at home was very muddy when it was first pumped out! It became clear after a while, what's going on?

Hello dear, the water in the well at home is very muddy when it is first pumped out! After a while, it became clear that the water contained a relatively large amount of iron ions.

In the well, because it is very deep, there is a lack of oxygen, it is in the form of ferrous ions, it is light green, you can't see it. When pumped up, a large area is exposed to outside air, and the oxidized air leakage cover is trivalent iron, that is, the trioxan bucket turns into iron, and the rust turns yellow. This situation should be specifically analyzed, if the yellow is bad, the iron content is excessive, or not good, you need to consider the water purifier filtration.

If it's not obvious, it's not a big problem, but it's best to use fresh: because the human body absorbs ferric element, it is absorbed in the ionic form of divalent ferrous iron, and for trivalent rust, it is still harmful to absorb too much. At first, the pump bottoms out, and after a while, the pump pumps out the surrounding sediment and the water clears.

After stopping, the pump bottomed out again, so it was still muddy water pumped up.

The water has just been pumped up, it is very turbid, it contains sediment and sediment objects, and there will be a lot of sediment at the bottom of the container after the sinking branch is carried by a worm. This has not happened before.

Take a look at the fact that water contains a relatively large amount of iron ions. In the well, because it is very deep, there is a lack of oxygen, it is in the form of ferrous ions, it is light green, you can't see it. When pumped up, a large area is exposed to outside air, and it is oxidized to ferric iron, that is, ferric oxide, and rust, which turns yellow.

This situation should be specifically analyzed, if the yellow is bad, the iron content is excessive, or not good, you need to consider the water purifier filtration resistance. If it is not obvious, the problem is not big, but it is better to use fresh: because the body absorbs iron in the form of divalent ferrous iron ions, and for trivalent rust, it is harmful to absorb too much.

Summary. I don't know why the water pumped out of the well at home is sometimes clear, sometimes so turbid. Is there any way to do it?

Hello dear, but sometimes the well water will be turbid, there are two reasons for this phenomenon, one is because of the rapid penetration of turbid water, which is also the main reason for the turbidity of well water.

Another reason is that the hot and cold currents in the water change during the change of seasons. Since well water is not easy to dispose of in wells, the easiest way is to sediment it in a water storage container at home.

This is done by adding alum to the well water, which condenses the turbid substances in the water and then turns them into precipitates. At this time, the sediment will be scooped up or filtered, and it will be much clearer.

I don't know why the water pumped out of the well at home is sometimes clear, sometimes so turbid. Is there any way to do it?

I don't know why the water pumped out of the well at home is sometimes clear, sometimes so turbid. Is there any way to do it? Hello dear, but sometimes the well water will appear turbidity, there are two reasons for this Xiangdong grinding phenomenon, one is because of the rapid penetration of turbid water, which is also the main reason for the turbidity of the well water.

Another reason is that the hot and cold currents in the water change during the change of seasons. Since well water is not easy to dispose of in wells, the easiest way to do it is to sediment it in a water storage container at home. This is done by adding alum to the well water, which condenses the turbid substances in the water and then turns them into precipitates.

If my answer is helpful to you, please give a thumbs up (comment in the lower left corner), look forward to your like, your work is very important to me, and your support is also the dynamic and vertical momentum of my progress. Finally, I wish you good health and a good mood!

How to solve the problem that the well has been coming out of muddy water, if the well has been out of Kai or muddy water, then there are these solutions, the first way is to use quicklime, the second way is to use fine sand, the third way is to use filtration equipment, and the fourth way is to use screen. So how should we operate it, you can continue to read and understand.

1. Quicklime: This method is to sprinkle quicklime, and then evenly sprinkle it all over the ground of the well and the inner wall of the lead, so that the water quality can be clear.

2. Fine sand: This method is very simple, that is, spread some fine sand at the bottom of the well, and then the water will be clear in a few days.

3. Filtration equipment: This method is to try to get a filtration equipment, but it should be noted that the water should not be pumped too fast, and the water should flow for a long time.

4. Gauze: This method is to wrap two layers of gauze on the head of the water pipe, and then wrap it around the well pipe horizontally with a brown string between the two layers of gauze.

There are many reasons for the turbidity of the water quality, which may be caused by the nearby sewage discharge enterprises, or the geological and surrounding environmental conditions of the well.

Hello dear! The solution to the problem of muddy water and mud is always muddy water and mud pumped out of deep wells: 1. The following filtration and other equipment, drilling wells, not only digging holes, but also putting some charcoal and so on below to filter, pumping water with a water pump, pumping to a certain time will indeed occur these situations.

After more than an hour, the sediment was pumped away and cleaned, but the sediment still went to the well like water. Try to get a filtration device, and it's best not to pump the water too quickly. 2. The bottom of the well is spread with fine sand, and it will be clear in a few days.

3. In general, in this case, continue to pump, the well pipe should be wrapped with two layers of gauze, and the two layers of gauze should be used to horizontally wrap around the well pipe with a brown string, and the fine particles will be built into a skeleton, and the well pipe will be pulled out and re-lowered, and the fine particles will seep into the well pipe when pumping. You must know that the pipe will go down all the way to the pebble layer, and the sand will be pumped out, and there will be no future of course, and it will be in the near future. If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress.

If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!