How do you remove Poussin s door panels? How do you remove the back door handle of the new Santana?

Remove Poussin. The door panel, first pry off the rubber inside the inner hand, and unscrew off the screws that fix the inner hand; The specific steps are as follows:

1. Pry off the rubber inside the inner hand first.

2. Unscrew off the screws that fix the inner hand.

3. Use a flat screwdriver.

Pry the buckle of the handle inside the door open.

4. After priing open the buckle of the inner handle of the door, take the inner handle off.

5. Buckle the combination switch on the door, there are no fixing screws here.

6. You can remove the door panel. (Completion of operation) <>

Both the front and rear door panels must be removed from the bottom up, and installed from the top down. The door trim has a groove in the window groove, which must be really embedded in the body, otherwise it will cause poor assembly and generate abnormal sounds.

First, use a slotter to lift the trim plate under the handle, and turn it out from the middle and then down.

When you open and remove it, you will see two black No. 8 screws inside, which can be removed using a sleeve.

Use a slotter to pull up the outer cover of the door opening handle and pull it out from the right side.

Pull the handle apart, pull the cover trim to the right and then outward, and remove it smoothly with a little force.

Start from below to pull out the door panel tenon, take your time one by one, and pull it out smoothly with a little force.

Use a slotter to pull the front half of the trim open, and with a little force, you can remove it smoothly.

When the trim is removed, two black No. 8 screws are visible, which can be removed using a sleeve.

Insert the slotted driver into the upper end of the handle trim and pry it open, and then pull it out slightly to remove it smoothly.

There are 2 screws removed from the handle, the wrench to open the door is removed, the safety plastic clip above the door is removed, and all the screws around the door are removed, and you can take it down.

There are 2 screws in the handle to remove, the wrench decorative block of the inner door can be removed by moving to the right, the four screws around the door are removed, and the safety plastic clip above the door is removed, and it can be removed by lifting it up.

Remove Poussin. The door panel, first pry off the rubber inside the inner hand, and unscrew off the screws that fix the inner hand; The specific steps are as follows:

1. Pry off the rubber inside the inner hand first.

2. Unscrew off the screws that fix the inner hand.

3. Use a flat screwdriver.

Pry open the buckle of the handle in the door of the Shen Bureau.

4. After priing open the buckle of the inner handle of the door, take the inner handle off.

5. Buckle the combination switch on the door, and there are no fixing screws in this wide star.

6. You can remove the door panel. (Completion of operation) <>

Summary. Hello dear! The steps to remove the Santana rear door handle are as follows:

1. First of all, prepare the tools needed for the whole disassembly and assembly process, a word to change the cone, a T-20 spline, and then prepare for the next operation process, the whole process uses these two tools, or quite easy. 2. Break down the inner handle by hand, and then you will see the left and right two small covers, take out the word change cone, and gently pry the two small covers with the word change cone, you don't need to take it off, you can pry it open. 3. At this time, we will see the screws that fix the inner handle, a total of two on the left and right, take out the T-20 spline, use the T-20 spline to disassemble the two screws, and the disassembled screws should be put away for installation.

4. After the screw is disassembled, the left hand holds the left side of the inner handle, and the right hand holds the right side of the inner handle, and then gently breaks it outward, so that the inner handle is separated from the big top, and it should be lighter when breaking it, because there is a small plastic clip on the inner handle, which is easy to break. 5. In this way, the inner handle will be removed, and the inner handle of the roof should be put away, preferably in a soft place to avoid wearing the surface.

This question is up to me, it takes a little time to type, so please be patient.

Hello dear! The steps of disassembling the handle outside the back door of Santana are as follows: 1. First prepare the tools needed for the entire disassembly process, a word to change the taper, a T-20 spline, and then prepare for the next operation process, the whole process uses these two tools, or quite easy.

2. Break down the inner handle by hand, and then you will see the left and right two small covers, take out the word change cone, and gently pry the two small covers with the word change cone, you don't need to take it off, you can pry it open. 3. At this time, we will see the screws that fix the inner handle, a total of two on the left and right, take out the T-20 spline, and use the T-20 spline to disassemble the two screws. 4. After the screw is disassembled, the left hand holds the left orange side of the inner handle, and the right hand holds the right digging side of the inner handle, and then gently breaks it outward, so that the inner handle is separated from the big top, and it should be lighter when breaking it, because there is a small plastic clip on the inner handle, which is easy to break.

5. In this way, the inner handle will be removed, and the inner handle of the roof should be put away, preferably in a soft place to avoid wearing the surface.

The operation is as follows: 1. First prepare the tools needed for the whole demolition process, and change the cone one by word.

handful, then open the door and prepare for the next demolition.

2. First remove the handle cover of the rear door interior panel. Take out the slotted taper and pry it up from the edge gap between the door trim panel and the inner handle cover as shown in the figure.

3. Pry open the clips inside little by little, a total of three clips, everyone must pry the right position when prying, and gently pry it.

4. After all the three clips are pried open, hold the door interior panel handle cover with your hand, gently pull it out, and remove it, check whether the clip is intact and stuck on the inner handle cover, it must be light, to avoid some scratches, affecting the appearance.

5. At this time, you will see the screws that fix the door trim panel, a total of two, take out the T-30 spline, remove the two screws with the T-30 spline, and put the removed screws together with the previous inner handle cover.

There was a small hole in the side of the door, and you could see a small plastic hole inside, and the extra piece of the small hole was hooked out with wire.

Let's talk about the front door handle car and push it forward, and then there is a screw on the front door handle car directly opposite the edge of the door, and you can unscrew it down!

Do you know how to dismantle the handle?

Summary. Hello 1

First, pry off the rubber inside with your inner hand.

Unscrew the screws that hold the inner hand pick in place.

Use a flat screwdriver to pry the buckle of the handle inside the door open.

Pry open the buckle of the inner handle of the door and remove the inner handle.

How do you remove Poussin's door panels?

Hello 1First, pry off the rubber inside with your inner hand. 2.

Unscrew or match the screws that fix the inner hand. 3.Use a flat screwdriver to pry open the buckle of the rubber in the handle chamber in the door next to the regiment.

4.Pry open the buckle of the inner handle of the door and remove the inner handle.

Hope it helps.

Thank you and I wish you a happy Mid-Autumn Festival.

I also wish you a happy Mid-Autumn Festival.

1. Use a flat screwdriver to pry down the lower trim plate of the door handle, and then open it outward from the middle down (the back door is the first half of the prying) 2. After removing the lower trim plate of the handle, you can see two black No. 8 hexagonal bolts inside, unscrew it with a socket wrench 3, unplug the plug of the window lift switch (there is a clip inside, you have to hook it from the back with your fingers to pull it out) 4, use a flat screwdriver to pry open the door handle decorative plate from front to back, and pull the door handle when removing it 5. Then put a wrench into it to pry, the town core to accept an interior panel is buckled on the door panel with a circle of plastic shoots, when prying, you have to use a little force, one by one.

Summary. How to dismantle the board in the 13-year-old Santana door.

Hello. Hello, I am your exclusive technician, attentive, careful, dedicated to answering your car questions, Yu Hongchang for you to find the corresponding problem solution and solution! Your problem is that the 13 Santana door inner panel disassembly, Qing Pao first, remove the screws in the handle handle, remove the screws in the door handle, and there is a buckle screw under the door panel that can be removed by turning the position