When the wall of the blank house is tiled, the original wall has latex paint, how to deal with it?

If there is latex paint on the original wall, it can be completely cleaned, and then the tile can be pasted, which is the most correct, and can ensure that the tile is particularly strong and will not fall off easily.

If there is latex paint on the wall, you need to scrape the latex paint off. Otherwise, the tiles will fall off when they are pasted.

Workers are required to scrape the gypsum powder, so that it dries quickly, that is, the strong life is leveled, and finally the paint is brushed.

The wall of the blank house cannot be directly painted with latex paint, because the wall of the blank house needs to be decorated with a normal process, and only in this way can it be decorated more appropriately. You should check whether the putty layer on the wall of the blank house is waterproof putty, if not, you need to scrape off this layer of putty and brush it again. Moreover, although some rough houses do use water-resistant putty, the quality of the products used may be particularly poor, and they also need to be re-brushed at this time, otherwise they will have a lot of bad effects on their future living experience.

Be sure to give your house a good putty before painting latex paint, which is a very important step. If this step is not done well, then there may be a lot of small cracks in the walls of the room, and there will be unevenness in addition to this. When scraping putty, you need to repeat it 3 or 4 times, and after drying, you need to use sandpaper to polish the wall, and you can paint it only after the wall is completely smoothed.

If the wall is painted directly without scraping putty, then the final effect of latex paint will be very poor, and the wall is not completely white after brushing latex paint, on the contrary, there may be some small hole-like black spots on the wall, which will affect the appearance of the wall. And if the blank room is directly brushed with latex paint, then the amount of latex paint required may be very large, and it may need to be brushed several times in the brushing process, and the flatness is relatively worse. <>

Therefore, if a rough house wants to paint latex paint, the first thing to do is to scrape putty, and the function of scraping putty is to make the wall whiter and make the wall smoother. There are many problems with the walls of the rough houses made by developers, so when decorating, you must scrape the putty several times to make the wall better, so that you can better brush the latex paint.

In the process of decoration, the rough house first needs to be leveled, and the wall should be painted in the decoration of the rough house, and then painted with latex paint.

The wall of the blank room cannot be directly brushed with latex paint, because the latex paint is easy to fall off, and it is easy to brush unevenly and cause unevenness to the touch.

Theoretically, it is possible to paint directly without scraping putty in the blank room, but the effect is very poor. For the decoration of the blank room, can the wall be directly brushed with latex paint without treatment? Unless you want that kind of mottled effect, which has also appeared in some industrial decoration cases, you can directly apply a layer of varnish to the cement wall, and some of them don't even brush the varnish.

This is just a case, and it is not recommended to paint the walls of the rough house directly.

It is definitely impossible to paint directly with latex paint, or you need to carry out a series of treatments on this wall first, and then paint some other substances. Finally, spray latex paint.

The wall of the blank room can not be directly brushed with latex paint, because the effect is not very good, and the consumption is relatively large.

No, if you do this, the walls will become uneven, and you can't directly use latex paint to brush it, you have to scrape it first, then paint white paint, and then paint latex paint.

Blank interior, wall surface does not have to deal with latex paint yourself. Unless you want that mottled effect, in some industrial-style decoration cases, sometimes a layer of varnish is applied directly to the cement wall instead of varnish. This is just one example, and in addition to that, it is not recommended to apply latex paint directly to artificial walls.

Rough cement walls can be directly coated with latex paint, do you admit it? If it's not advisable to brush it yourself, first know why. The normal decoration process of the blank wall is as follows.

The cement mortar is leveled and brushed with finishing agent. The plaster on the floor is flat and is only used when the wall surface is particularly uneven. Putty three times, can be spread mesh cloth optional.

Today's rough houses are basically surrounded by white walls, and this kind of rough houses may not have the conditions for applying latex paint. Some cities have such regulations, so developers can subcontract to renovation companies at a very low rate, and of course they can also be done with the cheapest materials.

You can wipe the same place repeatedly with a damp cloth and then wipe it. Then you have to shovel it all and scrape off the greasy stuff again. That starts with understanding the role of greasy.

Smooth the walls and paint them white. The greasy makes the wall surface tighter and smoother, and the paint of the latex paint is more uniform and does not penetrate the base layer. Waterproof putty can be used to cut off the direct contact between the wall and the latex paint, reducing the possibility of the latex paint falling off due to wall moisture.

In addition, cement is prone to shrinkage, and microscopic cracks may appear on the surface, and greasy can greatly alleviate the occurrence of microcracks.

For the above reasons, latex paint is applied directly to the cement wall. The bright effect of latex paint can be impressive, causing waste of material, and cement walls are also prone to cracking, which appear directly on the latex paint. It is not recommended to apply latex paint directly to the blank wall.

If you apply it yourself, you shouldn't have any problems. But cracks in the walls are for sure. That said, it's a problem that takes a long time, and the short one may appear in a week or two.

A little longer, it will appear in half a year.

No. The blank room cannot be directly painted with latex, the wall must be scraped flat. Because it is easy to have unevenness, and the brushing effect is not very good.

No, the wall of the rough room is too rough, and it needs to be treated to make the wall neat before you can use latex paint brush.

No. Because the effect of taking the latex paint brush directly is very poor, you should scrape the putty first, and then use the latex paint brush.

Yes. If you don't care about the flatness, you can directly make latex paint, but you need to make a layer of alkali-resistant primer because the cement-based anti-alkali directly destroys the latex paint film, to be precise, most of the emulsion is acrylic raw materials, and the alkalinity in the cement-based destroys the molecular structure. However, in the later stage, if the putty is scraped, a layer of interface agent needs to be made first.

The unevenness of the cement blank wall itself has little effect on the adhesion of putty in the later stage.

If you consider that you still plan to decorate in the later stage, then it is recommended to scrape the water-resistant putty and leave it blank. Because after the water-resistant putty is primed, there is no need to scrape the putty again in the later stage of the wall.

If you want to redo it, you have to shovel off all the original ones, scrape the putty and then apply latex paint.

The rough room has been painted with latex paint, if you want to paste wallpaper, just paste it directly.

Paint latex paint on the original wall, repaint it all, and paste it directly.

There are two ways to deal with it:

1.It is to snatch off the latex paint layer, and then make pockmarks on the wall, use a percussion drill or electric pickaxe, or chisel. This ensures that the tiles do not fall off. The fundamental solution is to chisel off the original wall skin to the brick layer. Then glue the bricks.

2.It is to remove the latex paint layer, and paste it with special glue for ceramic tiles, but the hollowing rate is high, and there is a large error that is difficult to adjust.

It is better to snatch it off, brush it strong, then scrape it white, and brush the alkali-resistant primer and topcoat. It's okay not to grab it, but you have to re-polish it with 180 mesh sandpaper, straighten the corner of the wall, level it with putty, then polish it flat, brush the alkali-resistant primer, and then brush the topcoat.

If it is latex paint, you can directly brush latex paint on the original wall.

The blank house has been painted with latex paint, but if you want to redo it, you must remove it all.

You can directly brush the newly bought Lu glue paint on the original Lu glue paint wall.

If you want to redecorate, you have to scrape off the original latex paint.

What kind of latex paint do you have nothing to do in the blank room, you have to get it all off.

If you have already brushed latex paint and still want to paint latex paint, you can brush it directly.

Latex paint. If you want to change the tile on the wall, you need to remove the latex paint layer, shovel it to the putty layer, and then make up for the uneven place in the putty layer, and then paste the tile.

If you want to have the best quality, you can remove the putty layer, but I personally think it's not necessary, as long as the original putty layer is in place, there is no need to spend that effort to eradicate the putty).

2. If the original tile is not available.

Hollow drums. You can't go straight on.

Laminate flooring. If there is a hollow drum, it must be knocked out.

3: Actually, it's not troublesome, you just need to lay the floor directly on the floor tiles, and put a moisture-proof film below, provided that the space is free.

Of course, it can't, the wall of the blank house is a cement wall, and there will be two main problems with latex paint directly, 1 is that the grip of latex paint on the wall will have problems, resulting in the phenomenon of paint peeling. 2. The wall is uneven and unsightly.

Yes, but the effect will be less effective. Because of the rough house when the developer delivers, there will be a lot of wall problems, the flatness of the wall is very poor, and many holes and cracks need to be filled.

Of course, you can't just brush it with latex paint. Because after all, the walls of the rough house are very uneven, and the surface is very pothole-ridden.

It can be painted directly with latex paint. In this case, it does not work very well, and it is not recommended.

No. In that way, the latex paint is easy to fall off, and you need to scrape the putty first, and then brush the latex paint after scraping the wall.