How to use the non marking hook and how to use the non marking hook

1. The smoothness of the veneer surface is not the most important, the important thing is that it is absolutely not breathable. For example, cracks in the tiles. It is difficult to stick firmly.

2. Avoid scratching the surface of the product with hard objects, and do not use rough cloth to wipe it.

3. Do not contact with organic solutions and corrosive chemicals and use in the gas environment with the above substances.

4. Pay attention to the standard load-bearing of the hook, and do not change the use and overweight use.

5. Do not use alkaline water or boiling water to wash the hook to prevent damage to the paint surface.

6. Please pay attention to the use of uneven, rough, and easy-to-fall surfaces on the plane.

7. Before use. Wipe the adhesion surface clean with a clean, soft cloth and allow it to dry thoroughly.

8. Please do not hang within 24 hours of installation.

If you need this kind of seamless paste hook, you can ask Du Niang, I am "Mei Si Mei Home".

The use of non-marking hooks is clearly indicated by various manufacturers. However, it varies according to different environments and the objects carried. Its use is very different and not static.

For the first type of suction cup type adhesive hook, the fundamental point is to exhaust the air and let the atmosphere fully manifest. To do this, different approaches should be taken depending on the actual carrying capacity. Otherwise, it will either fail to achieve the goal, or it will be too cumbersome.

For the second type of adhesive adhesive hook, it is simply to glue a double-sided tape behind the hook, which has strict restrictions on the requirements of the load.

For the third easy-to-take non-marking hook, due to the complexity of the comparison operation steps, there are detailed operation steps on the back of the product packaging, and it is best to consult the salesperson directly when purchasing.

1. How to use the traceless hook, no matter what type of traceless hook, the wall needs to be cleaned before use, and only the clean and tidy wall can fully exert the adhesive performance of the traceless hook.

2. When using the non-marking hook, you first need to tear off the adhesive tape on the surface of the hook, and paste the hook in the selected position.

3. After the non-marking hook is pasted, do not let go immediately, it is best to press the hook down the wall with your hands to stick the position of the sticker, and then let the glue closely combine with the wall.

4. After the installation of the hook, do not hang the items immediately, it is best to wait for 24 hours to let the glue completely solidify, so that as long as the hanging items do not exceed the load-bearing capacity, it is not easy to fall off.

The above is all the content of how to use the traceless hook, do netizens understand?

Usage of non-marking hooks: clean the wall, tear off the adhesive tape, press hard and wait for 24 hours.

1. The wall needs to be cleaned before use, and only when the wall is clean and tidy can the adhesive performance of the non-marking hook be fully exerted.

2. When using the non-marking hook, you first need to tear off the adhesive tape on the surface of the hook, and paste the hook in the selected position of Dongliang, and the air in the hook needs to be squeezed out when pasting, and no bubbles can be left.

3. After the non-marking hook is pasted, do not let go immediately, it is best to press the hook down the wall with your hands, and then let the glue closely combine with the wall.

4. After the installation of the traceless hook, do not hang the items immediately, it is best to wait for 24 hours to let the glue completely solidify, so that as long as the hanging items do not exceed the bearing capacity, it is not easy to fall off.

Types of non-marking hooks:

1. Suction cup type hook without Wang difference

This kind of hook is fixed on the smooth wall by means of suction cup, and the installation and disassembly of the suction cup type non-marking hook are relatively simple and convenient, and the range of use is relatively wide and reusable.

2. Double-sided tape non-marking hook

This kind of hook is to stick the wall and the hook tightly together through double-sided tape, the hook is more effective in rough walls, but after disassembly, it will have a certain impact on the aesthetics of the wall, and cannot be reused.

How to use the non-marking hook

1. When preparing to use the traceless hook, first of all, you must carefully check the external packaging (ordinary people often do not pay attention to this piece and tear off the packaging directly, and the use and steps of the traceless hook will be explained in more detail on the packaging).

2. Open the package and take out the non-marking hook and non-marking adhesive strip (special attention, the focus is on the non-marking adhesive strip).

3. Pay attention to the protective strips on both sides of the non-marking waterproof adhesive strip, uncover the protective strip on one side and paste it directly to the back of the hook. (Don't reveal the other side just yet).

4. Since the adhesive strip is a waterproof adhesive strip, the location is also in a humid and high-temperature environment such as bathroom or kitchen, if it is in the bathroom, please open the shower with bathing water temperature, rinse the wall ready for installation with water, and turn off the shower after the wall has a certain temperature. Dry the walls before using the ones that came with the package. Wipe the walls with an alcohol swab and then dry them with a hair dryer.

This step is very important when installing waterproof adhesive strips).

5. Uncover the protective strip on the other side, and then stick the non-marking hook directly to the wall. Remove the individual hook (the hook can be removed when pushed upward, while the strip and backplate are still glued to the wall) and press the backplate on the wall with your hand so that the strip is evenly stressed.

6. Then hang the non-marking hook and let it stand for 24 hours, so that the adhesive can be used normally after it is sufficient (please be careful not to exceed the load-bearing capacity of the non-marking hook standard).

7. The removal process is relatively simple. Remove the hook (leaving the back plate and adhesive strip on the wall) and stretch the adhesive strip vertically down until the back panel falls off.

Precautions for using non-marking hooks

1. Try not to exceed the load-bearing load.

2. Let the adhesive strip adapt to the environment before use (first wet the wall with water with a certain temperature, then wipe it dry, and then wipe it with an alcohol cotton strip and then blow dry).

3. Press evenly to make the pressure sufficient.

4. When taking it off, pull down vertically and evenly to prevent the strip from being pulled off (if it is broken, please use a hair dryer to blow the strip, and then pick up a section to continue stretching).

1. When preparing to use the traceless hook, first of all, you must carefully check the external packaging (ordinary people often do not pay attention to this piece and tear off the packaging directly, and the application method and process of the traceless hanging will be clarified on the packaging compared with the specific).

2. Pay attention to the maintenance strips on both sides of the traceless waterproof adhesive strip in the empty core, and lift the maintenance strip on one side of it and paste it directly to the reverse side of the hook (do not open the other side for the time being).

3. The location is also in a humid and high-temperature environment such as bathroom or kitchen, if it is in a clean room, please open the shower with bathing water temperature, wash the wall of the preparation device with water, and close the shower after the wall has a certain temperature. Dry the walls first, then scrub the walls with the alcohol swamp that comes with the package, and then dry them with a hair dryer later (this process is important when installing waterproof adhesive strips).

4. Lift the maintenance strip on the other side, and then stick the non-marking hook directly to the wall. Remove the individual hook (the hook can be removed after pushing it upwards and transporting it in, while the strip and backplate are still glued to the wall), and then press the backplate on the wall by hand to make the strip evenly stressed.

5. Then hang the non-marking hook and let it stand for 24 hours, so that the adhesive can be used normally after it is sufficient (please note that try not to exceed the load-bearing capacity of the non-marking hook specification).

6. The removal process is relatively simple. Remove the hook (with the back panel and adhesive strip hidden on the wall) and stretch the adhesive strip straight down until the back panel comes off.

In ordinary life, we always have a lot of items to use, and for the storage of these small objects, it has become a headache, and the appearance of the traceless hook is a good solution to this problem, but for some users, they are not familiar with this kind of product, thenAdhesive hooksWhat are the ways to use it? Let's take a look with me.

How to use the non-marking hook

1. Adhesive adhesive non-marking hook.

This is a relatively new style at present, not only has all the advantages of other similar products, but also has no requirements for the use area, whether it is a smooth surface or a rough wall, but the flatness of the bonding area must be good, and this kind of hook can be used many times.

2. Suction cup type non-marking hook.

This kind of product is mainly made of physical atmospheric pressure, the principle is simple, so it is widely used in the home, through the role of the suction cup, the hook is completely bonded to the wall, and the suction cup traceless hook installation and disassembly are very convenient, recyclable, but susceptible to the influence of temperature and time.

3. Easy-to-take non-marking hook.

This belongs to a class of adhesive style, through the use of adhesive strips, so that its adhesion becomes better, only some pressure, it can be well bonded to the wall, and the installation is quick and easy, you can use it immediately in a day, and it is also very easy to remove.

How to remove the non-marking hook

1. If the suction cup type is selected, the hook should be covered when removed, and then pulled it up, and then take the opportunity to remove it in this direction.

2. For the hook bonded with the adhesive surface, when taking it off, you need to put it on the top and bottom of the product with both hands, and then slowly pull the vertical of the adhesive strip down to 30 cm until the non-marking hook is completely removed, of course, there is a simpler way, which is to use the hot air of the hair dryer to blow the seamless hook evenly, and when the adhesive strip is softened, it can be removed directly.

3. Vinegar can also remove this kind of product, it has a certain corrosive effect, so that the rubber strip can be fully softened, and then the hook can be taken off intact, if the wall is printed with traces, you can use some turpentine to clean, but you can not use sharp objects to forcibly remove it, otherwise it is easy to cause damage to the hook, and it will also cause damage to the wall.

Summary: Okay, that's all aboutAdhesive hooksWhat are the contents of the use of the method, I hope to provide you with some help, I believe that in the future of the seamless hook selection process, friends will be more handy, buy their own satisfactory products.

In ordinary life, we always have a lot of items to use, and for the storage of these small objects, it has become a headache, and the appearance of the traceless hook is a good solution to this problem, but for some users, they are not familiar with this kind of product, so what are the ways to use the traceless hook? Let's take a look.

How to use the non-marking hook

1. Adhesive adhesive non-marking hook.

This is a relatively new style at present, not only has all the advantages of other similar products, but also has no requirements for the use area, whether it is a smooth surface or a rough wall, but the flatness of the bonding area must be good, and this kind of hook can be used many times.

2. Suction cup type non-marking hook.

This kind of product is mainly made of physical atmospheric pressure, the principle is simple, so it is widely used in the home, through the role of the suction cup, the hook is completely bonded to the wall, and the suction cup traceless hook installation and disassembly are very convenient, recyclable, but susceptible to the influence of temperature and time.

3. Easy-to-take non-marking hook.

This belongs to a class of adhesive style, through the use of adhesive strips, so that its adhesion becomes better, only need some pressure, it can be well bonded to the wall, and the source of the wide car and installation is quick and convenient, one day can be used immediately, but also very good to remove.

How to remove the non-marking hook

1. If the suction cup type is selected, the hook should be covered when removed, and then pulled it up, and then take the opportunity to remove it in this direction.

2. For the hook bonded with the adhesive surface, when taking it off, you need to put it on the top and bottom of the product with both hands, and then slowly pull the vertical of the adhesive strip down 30 cm forward until the seamless hook is completely removed, of course, there is a simpler way, which is to use the hot air of the hair dryer to blow the seamless hook evenly, and when the adhesive strip is softened, it can be removed directly.

3. Vinegar can also remove this kind of product, it has a certain corrosive effect, so that the rubber strip can be fully softened, and then the hook can be taken off intact, if the wall is printed with traces, you can use some turpentine to clean, but you can not use sharp objects to forcibly remove it, otherwise it is easy to cause damage to the non-marking hook, and it will also cause damage to the wall.

Summary: Well, the above is about the use of the traceless hook what is the content of the introduction, I hope to provide you with some help, I believe that in the future traceless hook selection process, friends will be more handy, buy their own satisfactory products.