Midea washing machine has power on but can t start?

1. What's going on when the washing machine doesn't start.

If the washing machine does not start, first check whether the socket meets the requirements and is plugged in well and whether the contact is good; Then check that the washing machine door is tightly closed; If the motor plug-in cable is not in good contact or the motor has burned out, it will also cause the washing machine to fail to start; If it is not done correctly, it will also cause the start to be abnormal, check to see if the washing machine has pressed the start button, if the faucet is on, etc.

2. What are the common faults of washing machines?

1. The drainage pipe is blocked.

First of all, check whether the drain pipe is normal, if the drain pipe is placed deformed and twisted, there is a fold pressure that will affect the drainage of the washing machine. Then check whether the inside of the drain pipe is unobstructed and whether there is any foreign matter blockage. If the drainage is not good due to this situation, it is enough to clean the drain pipe again.

2. The drain valve is blocked.

There is a drain valve on the right side of the washing machine, which will accumulate debris and cause clogging after a long time, so you only need to unscrew the drain valve cover and take out the debris directly.

3. The solenoid valve is damaged.

Since the washing machine is done with a solenoid valve conversion gear, if the solenoid valve is damaged, it cannot enter the dewatering process. In this case, the rust and dirt in the solenoid should be removed first, and if the washing machine still cannot drain normally, then the solenoid valve can only be replaced.

4. The computer control board is faulty.

Because the computer control board is short-circuited or the electromagnet is burned, the controller will fail, which is more serious and very inconvenient to repair, so the washing machine can only be replaced.

Midea washing machine has power on but can't start, according to what you said, the washing machine can't start when it's powered on, first check the start button to see how it is, if it doesn't work, check the computer board.

Answer: Hello, if this situation occurs in a fully automatic washing machine, you can troubleshoot the cause of the failure one by one according to the following methods. 1. The panel of the washing machine fails, first look at the plug of the washing machine and the power supply to see if there is any looseness, sometimes the power supply will not be powered, which will lead to the failure of the panel; If there is a power problem, you can find a professional maintenance master to replace the power supply. 2. Take down the panel of the washing machine to see if there is any problem in the panel.

The washing machine panel is generally buckled on top and can be removed with a little force. After the lower panel, you can see the structure inside, see if the power switch is broken, the power supply is the source of the washing machine's power, and if the switch is broken, the washing machine panel will fail; If there is a problem with the panel, you can only repair it or replace it with a new motherboard. 3. Another reason is that some soldering points in the panel are loose, and the current washing machines are soldered with tin, and some have been used for a long time, and the tin is oxidized, which will lead to poor contact and failure of the washing machine panel; If the solder joint is loose, you can also find a professional maintenance master to repair it.

4. If the power supply has been connected, the start button presses down the washing machine and does not move, and there is no response to work, it should be that there is a problem with the internal circuit or computer board of the washing machine.

Now the washing machine is intelligently controlled, it will work automatically after the setting is completed, the washing machine is not good for electricity, and it also needs water to work normally, and the door of the washing machine must be closed.

Hello, I'm glad to answer for you, Midea washing machine does not work when powered on: try to open the back cover of the washing machine and move the pulley by hand. If there is no jamming, the motor has a humming sound and does not rotate after the power is turned on, it means that the motor is short-circuited or damaged between turns, or the capacitor is not connected to the motor circuit.

At this point, cut off the power supply, remove the motor belt, and restart. If the motor still does not rotate or the speed is low, it is a motor failure and the motor should be repaired or replaced. 1. Please confirm whether to press the on/off button to start, and you need to press the start button after the washing machine is plugged in.

When you confirm that the power supply is fine, check the computer board again. Second, it may be a problem with the computer control board. Computer board finch core check method:

1. Lift the outer edge of the control panel upwards with your hand to separate it from the frame. 2. Unscrew the screws, take out the waterproof board first, remove the circuit board, and unplug the wire plug from the computer board. 3. Loosen the water level switch, install the fastening screws of the switch and the power switch, and remove the switches one by one.

The power indicator of Midea's automatic washing machine does not work for the following reasons, one control board button or control board failure, the second cover or door is not closed properly, and the third cover door position sensor is faulty.

There is an indicator light to indicate that there is power-on, which is generally a problem with the computer program controller (computer board). Just replace it with a new one, depending on how much the new computer costs.

Kiss <>, I'm glad to be able to answer for you. Midea's washing machine is not powered on, what's going on. Dear, first, the reason why the Midea washing machine is not powered on 1, when the washing machine is not powered on, first check whether the power socket of the washing machine is plugged in.

Today's washing machines are generally smart washing machines, as long as there is a little problem, the washing machine will not operate normally, and sometimes the power socket is not suitable will cause the washing machine to not be powered. 2. Detect the DC resistance of the power plug of the washing machine, see if there is a problem with the DC resistance, the DC resistance should be in the conduction state, if there is an abnormality, the DC resistance of the power supply is a problem, and this phenomenon will also cause the washing machine to not be energized. 3. The washing machines are relatively intelligent, and there will be a timer in the washing machine to open the crystal panel of the washing machine.

Look at the timer inside and the fuse on the DC resistor to see if it is broken, sometimes the voltage is unstable and the fuse will break. <>

1. Whether the socket meets the requirements, whether the contact is good, whether the door is closed tightly, and whether the contact of the micro delay switch is good. Poor motor plug-in contact or bad motor. Whether you have pressed the start button and there is a beep to indicate whether the faucet is open.

2.If both show good and are on, it may be that there is the most likely problem with the capacitor, followed by the motor, check if the capacitor and motor are working properly.

3.Secondly, check whether the brake of the dryer is correct, and whether the brake has a spring coming off.

4.Open the back cover and check if the brake line is broken and if the brakes are locked.

5.The aging of the belt and the loosening of the town will also cause dehydration and weakness.

6.Check whether the brain plate is damaged. The above have been tested, and the reason is still not found, so it can only be sent for warranty.

Abstract Hello, dear.

Summary of the reasons why Lu Shumei's washing machine can't start with pants:

1.Check that the power socket of the washing machine is plugged in.

Press the power button to confirm whether the light is on the machine panel, if not, please try to change to another socket or plug other electrical appliances into the socket of the washing machine to see if there is a response. If the power supply fails, please contact the property electrician of the community to check the power supply.

2.Normal power-on press Start Pause or Start Pause to confirm whether water can enter.

If there is no water, check whether the faucet is open, whether the water is stopped at home, whether the water flow is small, you can turn the faucet to the maximum, or contact the property to check the water pressure.

3.The washing machine manually refills the water, and the water level sensor will not automatically recognize it.

The machine defaults to a high water level, and the washing machine will keep "buzzing" and not working, so you need to continue pouring water into the bucket until the "humming" sound is eliminated, and the washing machine can be running and working.

Although the reason for "not turning on the faucet" is a bit simple and crude, and the washing machine cannot be started, it is still necessary to check whether the faucet is open or not, or whether there is any problem with the faucet and whether the water does not come out.

Once you've ruled out the faucet, it's time to see if the water pressure is enough. The faucet does not produce water with boiling water, and it also requires a certain amount of pressure. The water inlet of the washing machine is generally above the fuselage, and the faucet connected to the washing machine inlet in some homes is located at a low place, if the water pressure is too low.

It is impossible for water to flow into the washing machine and it will cause the machine to not start.

If the filter screen of the water inlet valve is blocked, and the washing machine cannot be started, you only need to clean the filter screen to solve the problem when repairing, but if the water inlet solenoid valve and relay of the washing machine are faulty, they can only be replaced, so that the washing machine can be used normally.

In addition to the reasons introduced above that cause the washing machine to fail to start, if the washing machine suddenly does not enter the water when the state knows that it cannot be started, after observation it is found that the washing machine in the process of water intake, has not reached the set water level height and suddenly stops entering the water, and the number of secondary occurrences is relatively large, then it may be that the water level switch of the washing machine has failed, at this time, you can choose to buy a water level switch again or ask a special maintenance personnel to come to repair.

1.Check whether the power socket is plugged in, press the [Power] button to confirm whether the light is on the machine panel, if not, please replace other sockets or plug other electrical appliances into the washing machine socket to observe whether there is a response. If the power supply fails, please contact the property electrician of the community to check the power supply.

2.Check if you press the Start button. The correct operation method of ruler elimination: [Power] [Start Pause] or [Start Pause].

3.When the power is normal, press [Start Pause] or [Start Pause] to confirm whether water can enter. If there is no water, check whether the faucet is turned on, whether the water is stopped at home, and whether the water flow is small, you can turn the faucet to the maximum, or contact the property to check the water pressure.

4.The washing machine manually adds water, the water level sensor will not automatically recognize, the machine defaults to high water level, the washing machine will always be "renting and humming", it does not work, you need to continue to pour water into the bucket, until the "hum" sound is eliminated, the washing machine can run and work. Power Supply: Select the water level as Low Water Level [Start Pause] or [Start Pause].

Midea's washing machine power switch is not responding, what's going on? Check the washing machine power outlet.

If not, please try to replace it with another socket or plug other electrical appliances into the socket of the washing machine to see if there is a response. If the power supply fails, please contact the property electrician in the small key clearance area to check the power supply.

2.Check if you press the Start button. Correct operation method: [Power] [Start Pause] or [Start Pause].

3.When the power is normal, press [Start Temporary Stop] or [Start Pause] to confirm whether water can enter. If there is no water, check whether the faucet is open, whether the water is stopped at home, and whether the water flow is small, you can open the faucet state bridge to the maximum, or contact the property to check the water pressure.

4.Washing machine.

Manually add water, the water level sensor will not automatically recognize, the machine defaults to high water level, the washing machine will keep "buzzing", it does not work, you need to continue to pour water into the bucket until the "humming" sound is eliminated, and the washing machine can run and work. Power Supply: Select the water level as Low Water Level [Start Pause] or [Start Pause].