Fully automatic washing machine washes normally, but does not dehydrate?

If the fully automatic washing machine washes normally, but does not dehydrate, it may be due to one of several reasons:

Motor failure: The motor is a key component for dehydrating a fully automatic washing machine, and if the motor fails, it may cause the washing machine to fail to dehydrate.

Broken drive belt: The drive belt of a fully automatic washing machine is an important part that connects the motor to the barrel, and if the drive belt breaks, it may also cause the washing machine to fail to dehydrate.

Clogged water tank: If there is debris clogged in the water tank, it may cause the washing machine to not spin properly.

Washing machine failure: If other parts of the washing machine fail, it can also cause the washing machine to fail to dehydrate.

It is recommended that you check the above several possible causes or have a professional repair carried out.

Generally, there is a problem with the solenoid valve.

<> If your fully automatic washing machine doesn't wash but dehydrates well, it could be due to several reasons: self-ordering.

Wash Procedure Selection Questions: Check that you have chosen the correct wash programme. If the selected program is not a washing program, the washing will not be performed.

Also, if you choose some special washing programs, there may be some limitations, such as rinsing only or dehydrating without washing.

Washing machine water level sensor is faulty: Check if the washing machine water level sensor is working properly. The water level sensor is a key component in controlling the water level of the washing machine, and if the sensor fails, it can cause the washing machine to fail to wash.

Washing machine drain pipe problem: Check if the washing machine drain pipe is normal. If the drain pipe is clogged or bent, the washing machine may not be able to drain the water and thus not carry out the normal washing operation.

Washing machine controller problem: Check if the washing machine controller is working properly. If the controller fails, it can cause the washing machine to not function properly.

If you are unable to solve the problem on your own, it is recommended to contact a professional washing machine maintenance personnel or a washing machine after-sales service center for repair or repair.

The washing machine cannot be washed, which is usually caused by the failure of the water to enter or the failure of the water to enter the washing machine.

1. Troubleshooting methods for more than water ingress:

1. The problem is mostly in the water level detection switch, due to the poor contact caused by oxidation, dirt or ablation of the contact, the power supply can not be turned on, causing more than water ingress, at this time the water level switch should be overhauled or replaced.

2. If the pressure pipe is worn and broken due to a long period of use, or the pressure pipe is in poor contact with the water level switch and the outer barrel air nozzle or disconnected, causing air leakage, it can also lead to more than water ingress, because the computer board is not at the pressure and the water level switch does not work, and the water level is not yet in action, at this time, the pressure pipe should be checked for wear and whether there is poor contact or disconnection between the two joints.

3. Due to the long use time, there are foreign objects blocking the air valve mouth, resulting in the pressure cannot be transmitted to the pressure switch.

At this time, the large nut should be unscrewed, and then the inner barrel should be taken out to remove the foreign object blocking the air valve.

4. The valve core of the water inlet valve is stuck, resulting in the inability to reset, resulting in the washing machine being flooded, and the water inlet valve should be overhauled or replaced.

5. If everything is invalid, you should try to replace the computer board, because all actions are controlled by the computer board.

Second, the maintenance of no water failure:

1. Turn on the power supply, the ears are close to the water inlet valve for "buzzing" sound, if so, check whether the tap water is cut off, close the faucet, screw out the water inlet pipe joint to check whether the filter screen of the water inlet valve is blocked by foreign objects, and if there is a pull out of the filter screen for cleaning. If the problem is not solved, the inlet valve should be replaced, and the valve core of the inlet valve may be stuck and cannot be opened.

2. If the water inlet valve does not have a "buzzing" sound, you should try to replace the computer board at this time, and the problem may be on the computer board.

1.The automatic washing machine cannot be washed but the dehydration is good, the reason should be that there is a problem with the water level switch (water level controller) of the washing machine.

2.When washing normally, set the washing program and the water level switch, start the washing machine, and the solenoid water inlet valve opens ,..

3.When the water filled reaches the set water level, the pressure in the air chamber at the bottom of the bucket of the washing machine increases, and the air pressure is transmitted to the water level switch.

4.At this time, the computer controller of the washing machine will issue a command to stop the power supply of the solenoid water inlet valve, turn off the water filling, and start the washing machine at the same time.

5.If you can't access the washing program to do laundry, the water level switch is not filling the washing machine's computer controller.

The fully automatic washing machine cannot wash the floor, but the dehydration is good, first check if there is a problem with the water level sensor of the washing machine, and whether the washing machine has too much clothes and exceeds the load of the washing machine.

If the motherboard's program is missing, or the program file is damaged, in this case, the only way to solve the problem is to repair the motherboard or replace the motherboard.

In this case, it may be due to the overheating of the washing machine motor caused by the external environment and excessive washing of clothes, and the motor thermal protector automatically disconnects the circuit to stop the washing machine, and after a while, the washing machine motor cools down and starts to work again.

The automatic washing machine can not be washed and can be dehydrated, which is generally caused by the failure of the water level sensor or the blockage of the water inlet valve.

If you say that the automatic washing machine can't be washed, but it can be dehydrated, then he is washing this motor is damaged, you can come in and get a belt or a motor or something, and see if there is anything abnormal?

This type of situation usually occurs when there is a problem with the water level switch of the washing machine, or there is a problem with the washing program and the burden on the bottom of the bucket increases, causing the signal of the control board on the washing machine computer to be confused, or it is based on the internal wiring of the washing machine. The specific solutions are as follows: 1. The automatic washing machine cannot be washed but the dehydration is very good, the reason should be that there is a problem with the water level switch (water level controller) of the washing machine; 2. When washing normally, set the washing program and the water level of the water level switch, start the washing machine, and the electromagnetic water inlet valve will be opened at this time, and the washing bucket will be filled with water; 3. When the water injection reaches the set water level height, the pressure of the air chamber at the bottom of the washing machine bucket increases, the air pressure is transmitted to the rubber diaphragm of the water level switch to promote the electrical contact to be connected, and the water level switch sends an electrical signal to the computer controller of the washing machine that the water injection reaches the set liquid level height; 4. At this time, the computer controller of the washing machine will issue a command to stop the power supply of the electromagnetic water inlet valve, turn off the water injection, and start the washing machine motor at the same time to start the washing work; 5. If you can't enter the washing program for the washing process, it should be that the switch of the water level sensor does not send an electrical signal to the computer controller of the washing machine that the water injection reaches the set liquid level height; It means that there is a problem with the water level switch (water level controller) of the washing machine; 6. It is normal for the automatic washing machine to carry out the dehydration program and water injection, which means that the circuit and computer controller of the washing machine are normal and there is no problem.

Hello, I am happy to answer for you: the reason why the fully automatic washing machine is only dehydrated and not washed :) Check whether the washing machine is placed smoothly, regardless of whether the ground is flat or not, the washing machine must be perpendicular to the horizontal surface.

2) Check whether the clothes in the bucket are placed unevenly, resulting in dehydration shaking and noise, at this time, the cover should be opened, and the clothes should be evenly placed on the walls of the barrel around the bucket. (3) Check whether the four booms on the bucket are consistent, and should be adjusted consistently. Whether the spring elasticity is the same, if the elastic force is not the same, the new spring should be replaced with the same elastic force.

The upper part of the bucket of some washing machines is provided with a fixed protective belt in order to prevent the bucket from swinging too much when dehydrating, and there is a tension spring on the protective belt. (4) The balance ring at the top of the dehydration bucket is ruptured or leaking, so that the dehydration bucket loses its balance when it rotates. Just replace the balance ring and it will solve the problem.

5) Check whether there is a foreign body between the inner barrel, the wave wheel and the outer barrel, and if there is a foreign body, take it out. (6) The fastening screws of the flange of the dewatering bucket are loose or broken. Just tighten or replace the flange.

7) The dehydrated bearing is seriously worn or loose. Simply tighten or replace the dewatered bearings. (8) It may be that the nut of the adjusting rod on the drain valve is loose or worn, resulting in insufficient opening distance, so that the pawls and ratchets of the clutch rub against each other when they rotate, and the position of the adjusting rod should be adjusted at this time.

I hope mine is helpful to you, please give me a thumbs up and wish you a happy life.

1. It may be that the panel door of the washing machine is not closed well or the switch of the top cover is damaged, or it may be that the switch is in poor contact, because the washing machine is a high-speed action when dehydrating, and the top cover is not allowed to be opened. Therefore, there is a linkage switch on the top cover, which will automatically disconnect as soon as the cover circuit is opened, check whether the top cover is covered, or it may be that the top cover sensor is faulty and needs to be replaced. 2. It may be caused by the blockage of the drainage system of the washing machine or the broken drain valve, the washing liquid in the water cylinder can not be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch can not be reset, and the washing machine can not enter the dehydration program, you can wait until the foam is discharged to enter the dehydration process.

3. The drain valve does not open the clutch conversion, and if the solenoid valve is damaged, it will also make the dehydration unable to operate normally.