-
The correct way to use toner: Use toner after each face cleansing, remember not to pat your face directly, because this will cause bacteria on your hands to infect your face, and in addition, the toner has been lost before it has been absorbed by your face**. You can pour the toner onto a cotton pad and wipe it along the texture of the skin from the inside out.
The toner you choose is different for different skin types, so be sure to choose one that suits you.
-
Wipe method:1Pour the lotion over a cotton pad and allow it to absorb well.
2. Wipe along the texture of the skin from the inside out, so as not to pull the appearance of fine lines on the skin too much.
Patting method: 1. Pour the lotion on the cotton pad first.
2.Using a pat, apply the lotion to the face.
3. Pat all parts of the face fully to help absorb the lotion.
Question: Are lotions and creams different?
Asked lotions and creams I massaged for a few minutes.
-
The role of toner and how to use it correctly.
-
Pour it in the palm of your hand, hold it hot, pat it on your face, use it to absorb, and at night you can also pour some toner and put it in the bottle cap to soak the compressed ** in the toner, apply it to your face for 15 minutes, and after applying, gently pat your face with water, the effect is better, the toner is to increase the moisture of **, and the moisturizing effect is better.
-
Spray onto face and gently pat until absorbed.
-
After the wet compress, the water is full of light.
-
Just pat it on your face after washing your face.
-
The role of toner and how to use it correctly.
-
The correct way to use water emulsion is a must-have for delicate girls.
-
Proper use of toner and steps1. First of all, the first step is to take an appropriate amount of toner and apply it to the face.
2. In the second step, it should be noted that many toners are liquid that can flow, and we apply the toner in the process.
3. The third step is to constantly use the beauty fingers, that is, the pads of our middle and ring fingers, to pat the face to let the toner be absorbed by the face.
4. The fourth step, the so-called dead angle position, refers to the position of the corners of the mouth, the corners of the eyes, and the wings of the nose.
5. In the fifth step, there is still residual liquid on the face at the end, which can be gently patted with a cotton pad.
-
1. First of all, the first step is to take an appropriate amount of toner and apply it to the face, it should be noted that many toners are liquid that can flow, and we apply the toner in the process.
2. Constantly use the beauty fingers, that is, the pads of our middle and ring fingers, to pat the face to let the toner be absorbed by the face.
3. The so-called dead angle position refers to the position of the corners of the mouth, the corners of the eyes, the wings of the nose, and finally the residual liquid on the face, which can be gently patted with a cotton pad.
1. If you use toner as the last procedure of cleansing, it can remove residual marks. Then you should wipe it with a cotton sheet from the bottom to the top, and "press" it a few times on the nose, forehead, and chin, and then "fan" it on the face with both hands. Cotton slices are best used to absorb toner but not be able to wring out droplets. >>>More
When you plug your teeth after eating, you can use dental floss to effectively remove the food residue between the teeth, solve the discomfort of the three teeth, and feel that after brushing your teeth at night, you can remove the food residue and plaque to prevent the appearance of dental diseases. >>>More
Before using the plugging king, clean the base layer first, so that there is no sand and no hollowing. >>>More
Here's how to use the humidifier correctly:1. You can't add tap water directly, tap water generally contains a lot of minerals, which will cause damage to the humidifier and cause pollution to the air, so it is best to use pure water or distilled water. >>>More
There are 4 steps to <> the correct use of caliper measurement, which are to observe the size of the workpiece to be measured, observe the workpiece to be measured, pull the caliper open, and record the caliper reading. >>>More