The correct way to use the plugging king

Before using the plugging king, clean the base layer first, so that there is no sand and no hollowing.

And it is necessary to keep the base layer dry before construction.

Also pay attention to the design of exhaust holes at the construction level. It is recommended to set one for every 36 square meters. In the case of extremely cold conditions, it is recommended to use water of about 21 degrees Celsius for blending, which is conducive to later use.

It is recommended to use up the plugging king material within 5 days for each blend. Otherwise, the effect will be affected.

When brushing, it is divided into 2 or 3 times, and the direction of scraping up and down should be carried out horizontally and vertically, so that the base surface is more uniform. It is advisable to be non-sticky, and the interval between each time is about 24, which is determined according to the construction environment and the degree of curing of the coating film.

Plugging KingThe correct way to use it, unpack it and mix it with water appropriately, stir it to the powder without unity, and basically complete the mixing process when it is almost solidified. Clean the surface of the crack to be repaired, dig a small hole and pour it into the plugging king, complete the bonding with the gap, and wait for air drying.

Usually one kilogram of plugging king is added with kilograms of water, and after they are stirred into a homogeneous slurry, they are filled in the chiseled bell. The water temperature should not be less than 5 degrees Celsius or more than 40 degrees Celsius when stirring, and after the final filling is completed, the exterior of it is coated with waterproof mortar.

After another week, it can be used after a week.

Advantages of Plugging King:

1. The plugging king is usually used in waterproof projects, and it can stop leakage immediately with water pressure. It is particularly easy to operate and can be used by simply adding water to it and stirring it. And it's non-toxic, harmless, and non-polluting.

Adding a certain amount of silicate hydrochloric acid cement to it can greatly shorten its setting time, and it is the same as the use time of the building.

2. And it can be used in the kitchen and bathroom room, roof, and basement of this elastic concrete structure, and it is used in a particularly wide range. The plugging king can quickly plug the leak, its initial setting time is 2 minutes, and the final setting time is 15 minutes.

3. It can be constructed on the back or front of the water, and can become a whole that will not age after being combined with the base layer. And it has particularly strong water resistance, its coagulation is also particularly strong, its coagulation time can be adjusted according to their own needs, and then it can be done in one step when waterproof and bonding.

The correct way to use the plugging king is as follows:Plugging King is a kind of product that quickly fills leaks in wall corners, floor drains, water inlet pipes, sewer pipes, filling large holes, etc. in home decoration.

1. The first step is to pour the powder of the plugging king into the barrel.

2. In the second step, pour the water in the ratio of :1.

3. The third step is to stir quickly.

4. The fourth step is to clean up the dust on the surface that needs to be repaired and soak the surface with water.

5. The fifth step is to evenly wipe the plugging king on the edge of the gap.

6. In the sixth step, fill the big hole in the wall with the plugging king.

7. The seventh step is to pay attention to sprinkling water after smearing and curing to prevent dry cracking.

First pour a small amount of water into the bucket, then tear a small hole in the bag of the plugging king, and then pour the plugging king into the bucket, stirring while pouring, the fast-drying plugging king must be stirred at the fastest speed, and use it immediately when stirring to a viscous state. After the plugging king is stirred, immediately fill the stirred plugging king quickly.

Plugging KingHere's how to use it correctly:

Plugging king is a kind of home decoration for wall corners and floor drains.

Products that quickly fill leaks such as water inlet pipes, sewer pipes, filling large holes, etc.

1. The first step is to pour the powder of the plugging king into the barrel.

2. In the second step, pour the water in the ratio of :1.

3. The third step is to stir quickly.

4. The fourth step is to clean up the dust on the surface that needs to be repaired and soak the surface with water.

5. The fifth step is to evenly wipe the plugging king on the edge of the gap.

6. In the sixth step, fill the big hole in the wall with the plugging king.

7. The seventh step is to pay attention to sprinkling water after smearing and curing to prevent dry cracking.

Kiss! Hello, happy to answer your <>

The correct way to use the pro-plugging king: first of all, the base layer needs to be cleaned first, and the humidity is preferably less than 5%. Then pour the plugging king into the container and add an appropriate amount of water to stir, stirring quickly, and wait for it to become a slurry before you can start painting.

Painting the plugging king should be divided into three times, and the thickness of each time should be the same, and then apply a protective film after painting. The plugging king is mainly used in waterproof engineering, it is with water pressure, and it can be done immediately to stop leakage. The operation of this product is relatively simple, only need to add water to mix and use, and it is also non-toxic, harmless and pollution-free, which can add Portland cement to adjust its retarding time, and can also have the same life as the building.

It is generally suitable for non-elastic concrete structures such as kitchens and bathrooms, basements, roofs, etc., and it can strengthen the waterproofing of various yin corners and pipe periphery, and can also be used to bury hanging hooks and sealing equipment railings. Hope mine can help you <>

Do you have any other questions?

Plugging King is a common pipe plugging material, and here is the correct way to use Plugging King: Preparation. Turn off the water source at the leak and clean the leak with absorbent materials such as towels or paper towels to ensure that the surface is dry.

At the same time, it is also necessary to open the plugging king and stir well. Smear the king of plugging leaks. Apply the plugging king evenly around the leak to cover the entire leak area as much as possible.

If it is a pipe leak, you can apply the plugging king above the pipe leak. Wait to dry. Wait for the plugging king to dry completely, usually 10 to 15 minutes.

Check the effect. After waiting for the plugging king to dry, check again whether the leakage has stopped leaking, if there is still leakage, you can reapply the plugging king. It should be noted that the plugging king is only suitable for small water leaks, and for larger water leaks or broken pipes, you need to seek the help of professional maintenance personnel.

When using the plugging king, we should also pay attention to its safety, and try to avoid contact with ** and inhale its volatile gases. In case of accidental contact, rinse immediately with plenty of water and seek medical attention**.