The tiles in the house feel like they are not being paved, is there a way to remedy it?

Re-tiling the tiles, as there is a high risk of damaging the tiles in place when the tiles are raised. Go to the merchant to check the batch number of the floor tiles, because the production time of each product is different, and the color is different, so the regular manufacturer will mark the color of the batch of products**, and it would be better if the packaging box was still there. In the corner of the floor tile hollow position through the reserved gap for watering, the gap between the tiles with a small shovel to smash open, and then pour cement with water into the gap.

<> then use a rubber hammer to gently tap the hollow drum position, the cement mortar will automatically flow through the gap to the hollow drum position, until it is filled, if the requirements are not too forced, if the beauty of the seam has not been done, directly close to the hollow drum of the floor tile joint, with a wallpaper knife or a small shovel knife with a batch of putty, dilute the cement with water, not too thin, pour it on the joint, with a small leather hammer keep beating, until the cement slurry completely penetrates into the floor tile joint, the tile that needs to be replaced is cut along the diagonal with a cutting machine, Be careful not to go to the four corners of the tile, and the distance from the corner is about 10-15 cm.

If it's a wooden floor, it's possible. It can be readjusted, some will have no sound, some are not paved, or the ground is uneven, then it has to be re-paved or the ground is re-leveled and then paved to completely solve the problem. Continue to beat the floor tiles until they are level, check whether the ground mortar is full, and then evenly apply a layer of plain cement slurry on the back of the floor tiles; If the hollow drum rate is not too high, or has been used to make a perfect seam and there is more obsessive-compulsive disorder, can only be replaced, the width of the tile gap is different, the joint smoothness of the tile can not be guaranteed at all, but also affects the consistency of the tiles, the height and width of the floor tiles are different, you can choose the beauty of the joint remedy, but can not solve the actual problem, if the floor tiles are not paved, the bottom cement mortar is not evenly paved.

The width of the floor tile gap is different, the remedy is not nothing, the tile gap can only be cut with a cutting machine, but there is a certain risk of porcelain collapse, and it needs to be operated carefully.

If it feels like it is not paved at the time of paving, it can be adjusted at that time, but if it is done after the cement under the second day solidifies, there is no way to remedy it.

There is a way to remedy it, use an air hammer on the tile, and carry out careful hammering to make the tile firmer.

I feel that the tiles are not paved, there is no way to remedy, unless it has just been paved, it can also be remedied, if it has been a long time, there is no way to remedy.

There is no remedy, because the project is very large, and it can only be resurfaced, so there is no remedy.

If you feel that there is a hollow drum, you can pour some cement slurry into the gap in the floor, and when the grout is dry, you can fill in the hollow drum.

After the floor tiles are paved, it is found that it is uneven, and the method of remedy:

1. If the solidified cement is not dry, you only need to gently knock the floor tiles with a wall knife until this brick is at the same level as other bricks.

2. The solidified cement has dried, if it is a few uneven bricks, you need to use tools to take out the uneven floor tiles, and then you need to replace it with new bricks.

3. If the floor tiles in a large area are uneven, it is recommended to rework them all.

Causes of uneven floor tiles:

1. In the process of paving the tiles, if the construction workers do not pave in accordance with the arrow direction on the back of the tile, the wrong operation will lead to the overall unevenness of the tile after the completion of the paving, so it is necessary to remind the construction personnel at the beginning whether to pave in accordance with the direction of the arrow.

2. Some owners will require the construction personnel to seamlessly pave the tiles, although the tiles are beautiful, but the pursuit of beauty should also pay attention to the quality. Tiles paved in this way, it is easy to appear uneven in the later stage, whether you know how to pave tiles or not, the first thing to remember is that it is taboo to paste tiles without leaving seams!

After the tiles are pasted, it is found that it is uneven, which is caused by the carelessness of the decoration master. If the solidified cement is not dry, this situation is relatively simple. You only need to gently tap the floor tile with a knife to guide this floor tile to the same level as other floor tiles.

If the solidified cement has dried out, the situation is repaired to be comparative. It is necessary to use tools to take out the uneven floor tiles, and then kick them in, and then use putty to brush the flat cement solidification after doing it.

If a large area of floor tiles is uneven. It is recommended to rework them all. In order to avoid foot injuries when walking in the future.

Let the master rework. 1 cent does not need to be added. If it's a small area.

Then the uneven bricks need to be reworked. Free rework. If it's dry.

Then you need to break the floor tiles and buy them again, and re-lay them.

Warp up, the cement sand is flattened and then pounced, or a layer of carpet is laid on top to reduce the stress area.

up a few empty bricks and re-pave them.

This phenomenon can only be from the new floor from the new uplift good pavement, in order to fundamentally solve the problem, but there will be a certain problem, because the old and new tiles are not the same, there is the problem of color difference, if the economy allows, it is recommended that you pave from the new, so that you can solve the problem from the root, and do not have to worry about the problem of color difference.

You can go to the "Loving Residents Community" and ask the renovation consultants to hear what they have to say.

It is unlikely to be broken, and the only way to remedy it is to pry it open or smash it and re-pave.

First, the floor tiles are not paved, then the decoration master is required to pave from the new paving, paving to the end. This is the responsibility of the renovation worker, and usually the situation has to be re-paved. There is no other way to deal with it, and you must not polish and level the floor tiles, which is even more enjoyable.

Because sanding can damage the brightness of the tile surface, it may crack.

Second, the precautions for paving tiles.

1. According to the design drawings or design requirements, find out the color and pattern of the floor tiles. Pick out the defective tiles. In this way, you can prepare for the rest of the work in advance.

2 After the floor tiles arrive, they need to be sorted and classified, and remember to place them in a safe place to avoid damage.

3. Before laying the floor tiles, they should be soaked to avoid the absorption rate of the floor tiles causing the absorption of water in the cement and causing tightening and cracking.

4. The ground needs to be wet with water with a spoon or water hose. This work reduces dust. It also allows the ground to absorb some of the water. There will be no water shortage.

5 Next, it is the mixing of the cement bedding. The volume ratio of cement sand for laying floor tiles is best about 1:5, sprinkle and stir evenly, and the thickness should be about 3cm; The joint layer and the floor tiles should be paved at the same time in sections, and cement slurry or dry mud should be used for bonding when paving.

6. After the floor tiles are touched with cement oil, they should be slowly beaten with a rubber hammer to meet the standard of the level. Remember, the cement oil must be smoothed, otherwise it is easy to hollow the floor tiles in the future.

7. The surface of the floor tile surface layer shall be clean, smooth and solid after half an hour after being pasted with a water rag; The width of the joint between the porcelain plates should meet the design requirements, and the width of the joint should not be greater than 2 mm. Unless there is a design requirement. Antique bricks are considered separately.

It is recommended to use it immediately, and it is more troublesome to resurface. Either you have to add a layer of laminate flooring along with the bedroom, which is more convenient.

Haha, don't offend relatives and solve the problem, how can it be so coincidental, I also encountered this problem last year!

If it is not paved and there is some emptiness, then it must be chiseled! If it's just uneven, then the only way to wax the floor is to adjust the wax color. It won't hurt if you wear slippers at home. I also ran the decoration market all day for this year, and I got the method, so I might as well try it.

This is very difficult, just pasted on the ground, the floor tiles can still be operated!

It seems that there is no choice but to endure and knock it out and start over.

Soak some pure cement first, then pry up the floor tiles, sprinkle some water on the bottom layer, then apply a layer of cement on top of the floor tiles, and continue to put them back in place, so that they can solidify for a few days, which is no different from the original paving.

This is a tragedy, so be careful when installing, and it will be very tangled if something goes wrong in the end.

If there is no way to remedy it, it can only be reworked and repasted.

You'll want to be prepared for reposting:

The first is to re-match the bricks, because it is very likely to damage the original tiles when the bricks are raised;

The second is that you have to go to the first merchant to check the batch number of the floor tiles you bought, because the production time of each product is different, and the color is different, so the regular manufacturer will mark the color of the batch of products**, and it would be better if the packaging box was still there. If it is not the same batch number, there will be color difference. You should pay attention to this; The third is to propose to the decoration company or foreman to replace the bricklayer master, because now people's skills are generally improved, as long as the operation is serious, there should be no such problem, almost all the floor tiles are not hollow; Fourth, the decoration company is required to check the quality of cement, if it is a cement quality problem, it will still be a problem.

Therefore, you should say what you should say in advance, and if there is a problem again, the other party will be fully responsible, and it is best to write down a written agreement, even if it is a few sentences, and then the dispute will be documented. Decoration is an annoying thing, don't be afraid of problems, as long as you can solve them in time, you have to forgive the other party. Therefore, it is very important to be polite and respectful to the master.

To re-lay the floor tiles, you must pry off the previously paved ones, and if you are careful in construction, you don't need to re-engage in water and electricity (too wasteful, not recommended).

If you only modify those pieces, it is not impossible, pry off those pieces first, pry them off together with cement, and then re-pave them with cement sand (re-paving is not as good as one-time paving).

If you use the floor, you need to look at the distance between the door and the ground, and the thickness of the laminate floor is: 8mm 1mm 12mm. Solid wood is even thicker.

If the door is already ordered, the floor will not be laid, so you can either sawn off the door a little or replace the door. (Newly laid floor tiles, floors··· Huh).

Kiss! Hello, I'm glad to answer your <>

How to remedy the unevenness of the tiles as follows: 1. If the tiles have solidified, then you need to take out the uneven tiles, and then grind the ground and then paste the tiles on it, and then brush the putty, and wait until the cement solidifies and you can walk normally. 2. In the case of no solidification wheel, you only need to use a tool to gently knock on the tile and keep it on the same level.

Ceramic tiles, also known as tiles, are refractory metal oxides and semi-metal oxides, through the process of grinding, mixing, pressing, glazing, and sintering, and form an acid-alkali resistant porcelain or stone, etc., building or decorative materials, called ceramic tiles. Its raw materials are mostly mixed with clay, quartz sand, etc., and have high hardness. It is mostly used for the beautification of the wall, and the cement is used to bond to the wall.

The surface of the full-body brick is not glazed, and the material and color of the front and back are the same, so it is named full-body brick. Full-body brick is a kind of wear-resistant brick, although there are varieties such as seepage bricks, but relatively speaking, the color of full-body bricks is not as good as glazed bricks. As the interior design is more and more inclined to plain design, so the whole brick has become more and more fashionable, the whole body brick is widely used in the hall, aisle and outdoor walkway and other decoration projects on the ground, generally less will be used for the wall, and most of the non-slip bricks belong to the whole brick.

The common specifications of full-body bricks are 300x300mm, 300x600mm, 400x400mm, 500x500mm, 600x600mm, 800x800mm and so on. Advantages: Due to the rough surface, the wear resistance and slip resistance are the best of all ceramic tiles.

Disadvantages: Its unique structure determines the texture and effect of the whole brick, and the decorative effect is poor. Hope mine can help you <>

Do you have any other questions?

If the tiles that have been laid are uneven, the following methods can be considered to remedy it:1Smoothing the tile surface:

Use a tool such as a grinding wheel and a clamp to smooth out the protruding part and make the tile flat. This method is suitable for situations where the tile surface is less above the ground. 2.

Re-tiling: If there are many uneven tiles, or if the protruding part is large, you can consider re-tiling. When re-paving, the original tiles need to be removed and the new tiles need to be re-installed to ensure that the floor is level.

3.Use self-leveling materials: Self-leveling materials can fill in uneven parts of the ground and make the ground smooth.

When using self-leveling materials, Danhu needs to clean the ground first, then pour the self-leveling material on the ground, push it evenly with a tool, and wait for the material to level naturally. 4.Use brick spacers:

If the uneven tiles are caused by the uneven base floor, you can place a brick gasket under the tiles. Brick spacers can raise or fill in the tiles, thus flattening the tiles. It is necessary to choose the appropriate remedy according to the actual situation to ensure the flatness of the ground.

If you are unsure of what method you should take, it is recommended to consult a professional construction worker or a relevant building materials supplier.