Urgent!!!! The washbasin leak is stuck, what should I do?

Unplug the connecting pipe from the washbasin drain. Use a wooden stick to poke into the sink leak.

First of all, let's see if it's a software problem, whether the usual operation is inconsistent, whether there is any illegal operation, and whether it is suppressed.

Then on the hardware side, uninstall the pipes and other components and reinstall them.

Use the rubber repair tool of the toilet bowl to suction and see if it can be repaired.

Home Improvement TipsTake out the basin drainer and remove the fixings and flanges under the drainer.

When installing the basin for draining, pay attention to picking up the basin countertop, taking out the flange of the drainer, and fastening the flange of the drainer to the basin.

Once the flange is tightened, place the basin on the countertop and align the drain with the outlet of the countertop.

Coat glass glue on the contact surface between the drainer and the basin drain, pay attention to the uniform and complete fit to prevent water leakage, and the basin drain must be aligned with the basin drain when installing.

Aim the drainer at the drain and put it in flat, and note that the installation of the basin drain must take out the sewer retainer and screw it on the sewer, and remember to use a wrench to fix the sewer retainer.

After the basin is installed, it is tested after the glass glue is dried for 24 hours. Fill the basin with water to see if there is any dripping and leakage in the water.

Unplug the connecting pipe from the washbasin drain. Use a wooden stick to poke into the sink leak.

1All with a hard rod the size of the little finger, a soft towel or paper on the front bread, find a small hammer, and knock on the edge of the plug to move the position! Until knock on the side and knock down, it's all right!

Mine is replaced with a new one, and I replace it myself, so that I can improve my hands-on ability.

Find a wooden stick and stick it against the edge of the plug and smash it with a hammer to open it, because there is mud and sand on the contact surface of the plug.

Try smearing it along the gap with soap or shampoo, I did it hard last time.

Turn off the water valve, take it apart from below, and you're good to go. You can't get it from above.

Well, you should find someone who specializes in repairing water pipes, and there will be professional tools to help you solve it.

You can open the sewer pipe and use a stick to push the plug out from the bottom up. Then reattach the sewer pipe.

Unload the sewer pipe and poke it from the bottom up.

Bend over and have a screw slipknot at the bottom of the basin, grab it upside down with both hands, remove the drain pipe and use a 20 cm long screwdriver to push it up.

Brother, I see that your problem is your gospel. I am a professional bathroom repairer.

You look for a small sucker. (It's the kind of little pendant that sucks into the glass.) Thread a sturdy rope through the suction cup and suck it up.

Pull it up. It's easy. Because there's a ring of water-sealing glue next to the lid that you pressed.

It's reversed by you. Next time you tap.

What should I do if my suction cup falls off, and the suction cup hook always falls off.

What should I do if the suction cup hook always falls off.

The basin race you said should be next to the water spout or the kind of person who has the upper body on the mouth, this kind should be a guide rod under the basin, and the part of the screw linked to the basin plug may be loose, put it in the right position, and re-tighten, it should be on the line!

After a long time, the rubber around the plug is aging, why not replace it? Adopt it.

It's obviously broken, go to the plumbing and buy a sewer, about twenty or thirty yuan, and it's OK to change it.

I changed it to a new one and bought it on Tmall.

Patch or replace it.

The main reason for water leakage is that the ceramic is cracked or the interface is not consistent enough to cause water leakage, the former repair value is not large, the repair of ceramics is too troublesome and the cost is relatively too large, the replacement is better and cost-effective, and the latter has waterproof glue is enough to get it.

Ceramics should not be used acidic, it will corrode.

Change it, it's only about 50 yuan for another one! The installation method of the basin drainer is as follows:

1. Check whether the spare parts of the basin drainer component package are complete; 2. Remove the lock nut of the main body in the basin drainer assembly; 3. Wipe the drain hole around the basin, apply a circle of waterproof glass glue at the bottom of the drain hole, and then stuff the basin drainer into the drain hole of the basin and press the fitting surface tightly; 4. Place the basin on the countertop, install the lock nut from below, and lock the basin drainer body tightly on the basin; 5. Finally, lift the lever, lock the lock to the bottom of the lever, select the appropriate lifting height (there are many small holes on the lock piece for adjustment), use the card to jam the lever through the lock piece, and the installation project of the entire pull-up basin drainer is over.

Installation method of bouncing basin drainer:

1. Take the basin drainer out of the package; 2. Remove the fixing parts and flanges under the basin drainer; 3. Pick up the basin and take out the flange of the basin drainer; 4. Fasten the flange of the basin drainer to the basin; 5. When the flange of the basin drainer is fastened, put the basin flat on the countertop, and the drain is aligned with the mouth of the countertop; 6. Wrap the raw material belt around the appropriate position of the basin drainer to prevent water seepage; 7. Put the basin drainer in front of the basin drain; 8. Align the basin drainer with the basin drain and place it flat; 9. Take out the fixer of the basin drainer and screw it on the drainer; 10. Use a wrench to fix the basin drainer tightly.