After the toilet is filled, the water tank still has a sizzling sound, but what should I do if the w

There are two main reasons why the sewer pipes in the home need to be wrapped, one is to be soundproof, and the other is to make it look more beautiful. Here are a few ways to wrap the sewer pipe.

First of all, there are two less common ones, the first is to make a frame of a wooden keel next to the water pipe, and then install a gusset of PVC on its surface. The other is to nail a layer of wood on the surface of the keel frame, and then add aluminum-plastic panels. However, in this case, the wooden keel is more likely to deform due to moisture.

Nowadays, it is common to use soundproof cotton to wrap the sewer pipe, then put a keel on its surface, and finally add tiles. Because the sound insulation effect of tiles is not obvious, it is necessary to use sound insulation cotton. This method does not take up space, but it will be relatively high.

<> and another method is to build a wall, the sound insulation effect of this method is still very good, and there is no need to pack sound insulation cotton, ** cheap, but the space occupied is also relatively large.

<> this is what the bathroom does:

It leaks inside the pipe, not outside. If you don't adjust it, it will be this sound for a long time.

Solution: Open the top lid and bend the arm bar of the rubber cover to the middle (on top of the rubber cover), as far as possible, and generally it is fine.

This situation (the sound of water ingress) may also be caused by the water balloon is not tightly sealed, resulting in water leakage, water level drops, and then the water inlet valve works to replenish water, and the water ball can be directly replaced to solve.

Open the lid of the water tank, close the tap water cut-off door, remove the float to see if there is water inside, and take down the water gate control valve to clean.

As long as there is a sizzling sound, it is still slowly entering the water, only the sound stops, it can be non-stop will leak, after a while after the drainage, it is better to replace it with a new one.

After the toilet is filled with water, there is still a sound, not necessarily a leak, if there is a leak, you can see that there is water leaking out of the toilet.

If it is like this for a long time or all the time, it is that the valve is not tight, causing water leakage, if it does not ring after a period of time, it is normal.

This is the sound of water on the toilet, at the beginning of the large amount of water, and when the amount of water is about the same, the amount of water will slowly become smaller, knowing that the water tank does not have a float to block the water channel, there is no sound.

Leaky toilet tanks can lead to wasted water resources and increase the cost of water for households, so they need to be dealt with promptly. Here are some ways to solve this problem:

1.Inspect the inside of the tank for visible damage or cracks, and if so, the entire tank needs to be replaced.

2.Check whether the filling valve and drain valve on the tank are loose or broken, and need to be reinstalled or replaced.

3.If you find that the water level in the tank is too high, it may be because of the improper adjustment of the filling valve, the water level controller of the filling valve can be adjusted appropriately to make it work within the correct water level range.

4.Try cleaning the water valve and drain holes inside the tank to make sure they are not clogged with loose dirt or sediment.

5.Before inspection and repair, turn off the water source and empty the tank before flushing.

If you are unsure of how to operate or are having difficulties, it is recommended that you have a professional plumber service and maintenance carried out.

If the water tank still has a sizzling sound after the toilet is finished, but it does not leak, it may be due to the following reasons:

1.Improper tank water level: Setting the water level in the tank too high or too low can cause sizzling sounds. It is necessary to check whether the water level in the water tank is within the normal range, and generally the upper part of the water tank should be equipped with a mark.

2.Failure of the water inlet pipe of the water tank: check whether the sewer or water inlet pipe is blocked by jujube or foreign objects. If there is, it may cause the water inlet to be unsmooth, and the water level in the water rock containing tank is not stable, which will lead to a sizzling sound.

3.Damage to the internal components of the water tank: The components inside the toilet tank may be damaged due to long-term use, such as the inlet valve and drain valve, etc., which may cause abnormal pressure inside the tank and the water level to shake, resulting in a sizzling sound.

If there is still a sizzling sound in the water tank after the toilet is finished, it is recommended to check the selling posture and explain the reason first. If you don't handle it properly on your own, it may cause more serious problems, and it is recommended to have a professional inspect and repair it.

Summary. Hello dear There is a sizzling sound on the toilet tank, which is caused by the failure of the filling valve inside the water tank or the excessive flow of water. The sizzling sound when the toilet tank is filled with water is caused by a malfunction of the filling valve inside the tank or excessive water flow.

The filling valve is a key component inside the water tank, mainly used to replenish water to the water tank to ensure the height of the water level, if there is a problem with the filling valve, it will lead to the instability of the water level inside the water tank, and there will be a sizzling sound.

Dear, what's the sound when the toilet tank is filled with water? Is it normal?

Hello dear, the water on the toilet tank is big, and it is caused by the failure of the filling valve inside the water tank or the excessive flow of water. The sizzling sound when the toilet tank is filled with water is caused by a malfunctioning filling valve inside the tank or a large flow of water. The filling valve is a key component inside the water tank, mainly used to replenish water to the water tank to ensure the height of the water level, if there is a problem with the filling valve, it will lead to the instability of the water level inside the water tank, and there will be a sizzling sound.

Is it normal to have sizzling sounds?

Hello toilet talk about the water tank when there is a sizzling sound is not a normal situation, it is caused by the failure of the filling valve inside the tank or the excessive flow of water. The filling valve is a key component inside the tank, which is used to replenish water to the tank to ensure the height of the water level. If there is a problem with the filling valve, it will cause the water level inside the tank to be unstable and sizzle.

But when it was full, it was gone.

If the toilet tank is filled with water, but it is gone, it is caused by improper adjustment of the filling valve. The filling valve needs to be automatically adjusted according to the level of the water level inside the water tank to ensure the stability of the water level inside the water tank.

Reason: 1. The inner rubber cover moves: If the rubber cover in the water tank moves slightly, there will be a sizzling sound, and at this time, as long as the position of the inner rubber cover is adjusted.

2. Aging and damage of the sealing gasket: If there are hard objects such as sand particles in the water sealing gasket, it will lead to continued water ingress.

In addition, the weathering or wear of the seals can lead to continuous water ingress, which will require a new gasket to return to normal.

3. The water level float is damaged: after the back cover of the toilet is opened, a group of blue components will be seen, and there is a water level float at the end of the blue component, and when the water is full, the water level float will float and close the water inlet.

If the float component is damaged and does not float in place, it will lead to problems such as constant water ingress, and it is necessary to replace the water floatation component with a new one to solve the problem.

4. The fault may be caused by insufficient water pressure, at this time you need to check whether the filter screen on the inlet valve is blocked by debris, if so, as long as the debris is cleaned up, and then the filter screen is cleaned regularly.