What should I do if the cement tank is cracked? It s all leaking. 5

Pool masonry cracks or concrete cracks, according to the characteristics of pool cracks, the following methods can be used when selecting treatment methods.

1. For the cracks with a large number of cracks, the crack width is not large and most of the cracks are not penetrated, the waterproof cement mortar can be added on the surface of the water, and the five-layer waterproof method with better effect is especially suitable for the condition that the water head is not high. This is a treatment method with good results and convenient construction.

2. For wide and seepage cracks, plugging measures should be taken. The principle is to change the large leak to a small leak, the line leak to a point leak, and the piece leak to an empty leak, so that the leakage is concentrated at one or several points, and finally blocked. The commonly used plugging material is coagulant mortar, that is, an appropriate amount of coagulant is added to cement slurry or cement mortar (at present, the commonly used coagulant is mainly water glass, and a certain proportion of copper sulfate and potassium dichromate are added).

For the plugging of leaks without strength requirements, it can also be treated with coagulation materials such as cyanide slurry and propylene slurry.

3. Chemical grouting method.

1) Epoxy resin slurry, mainly made of epoxy resin, with curing agent, diluent, coagulant, etc. This material has the characteristics of high strength and strong adhesion, but under wet conditions, the use effect is poor.

2) Methyl gel slurry is composed of methyl methacrylate (main agent) and other additives. The viscosity of the slurry is lower than that of water, the fluidity is very good, the cracks can be poured very fine, and the bond strength is high, and the compressive and tensile strength of the aggregate exceeds the strength of general concrete. It is suitable for the repair of fine cracks in concrete.

3) Cyanide slurry, a chemical grouting material based on polyurethane. According to the day of grouting , change the cyanide coagulation with different additives and formulas to obtain slurries with different properties.

The prepared polyurethane is drilled with a percussion drill in the gap, and the polyurethane resin is injected into the hole with a special pouring nozzle and a high-pressure device, so that the resin will penetrate into all parts of the gap, and after the resin is cured (it has expansion characteristics), the water leakage problem is solved;

If the cracks of the cement tank are through-seams, and there are more, you had better coat it with 3 cloth and 5 oil FRP, which can be done once and for all. If you want to prevent bumps during cleaning, it is best to sprinkle another layer of clean sand on top of the resin coating of the curing process, and then make a protective layer. The specific use is determined by yourself.

Find a way to make it up.

It's better to make up inside.

If you can't patch it outside, then you have to plug the cracks first, and then patch a few with waterproof materials.

For external repair, it is necessary to use waterproof materials with good binding properties, such as permeable crystalline waterproof materials.

You can take a look at the water-based permeable crystalline inorganic waterproofing material.

Xiamen American perpetual condensate dps waterproof material Li Ji.

Summary. The bottom of the plastic bucket is cracked, you can use 502 glue to repair it, dry the bucket, there can be no trace of water, and then use glue to coat the inside and outside of the crack, and wait until the glue is dry, the repair work is completed, what to do if the crack leakage of the big plastic bucket is a big hole at the bottom of a large tank that can hold 2 tons of water, I don't know how to repair it? Please clean up the oil stain at the oil seepage, if the oil leakage location is small, you can use the good glue to smear the oil seepage, which can solve the leakage problem, if the area is large, it is recommended to replace the plastic oil tank.

The bottom of the plastic bucket is cracked, you can use 502 glue to repair it, dry the bucket, there can be no trace of water, and then use glue to coat the inside and outside of the crack, and wait until the glue is dry, the repair work is completed, what to do if the crack leakage of the big plastic bucket is a big hole at the bottom of a large tank that can hold 2 tons of water, I don't know how to repair it? Please clean up the oil stain at the oil seepage, if the oil leakage location is small, you can use the good glue to smear the oil seepage, which can solve the leakage problem, if the area is large, it is recommended to replace the plastic oil tank.

Extended information: There are the following ways to glue the plastic bucket when it is cracked: 1. Stick a piece of plastic or rubber to the crack after softening it with fire or heat source, but pay attention to safety 2

The same kind of plastic can be used to repair the cracks of the plastic bucket, which will flow down the plastic liquid and dry the bucket to be repaired. The liquid plastic is then drained to the cracks. And it melted into one.

After this treatment, it can be used for a long time. 3.If it is a thermoplastic plastic, it can be welded with plastic welding; 4.

If it is a thermosetting plastic, it can be glued with 502 and other glues. If the crack is not very large, you can also try it with egg white. 5.

Polyethylene has adhesive resistance, so it is recommended to try AB glue. But stick the same material on the outside. It's not a smooth glue.

6.Plastic is a synthetic polymer compound that can be freely changed. It is a material made by polymerization by synthesis or condensation reaction of monomer raw materials, and is composed of synthetic resins and additives such as fillers, plasticizers, stabilizers, lubricants, and pigments.

Kiss! Hello, happy to answer your <>

The method of repairing the crack leakage of the plastic pressure tank is as follows: polish the leakage by mechanical grinding, if the crack is the crack should be removed, if the porosity is mixed, the defect will be removed, and then the appropriate welding material will be used for the second welding repair. There are two types of welding repairs, which are repairs with water and without water.

In terms of safety and success rate, it is better to use the underwater electrode welding of Broco in the United States to weld with water, and it is recommended to use Vewelding600 electrode with excellent crack resistance to repair without water. 1. The installation of the device must be selected in a well-ventilated, dust-less and non-humid place, and the ambient humidity is between minus 10 degrees Celsius and 40 degrees Celsius. Outdoor facilities such as rain and lightning protection are required.

2. In order to facilitate the installation and maintenance of the device, 70 cm of space should be left around the device, a meter of space should be reserved at the manhole, and a drainage ditch should be set up on the surrounding ground. 3. After selecting the site, the foundation should be disposed of, and the tank support seat should be poured with concrete or masonry. After the base is solidified, the tank is hoisted and stabilized, and then the accessories are installed and the power supply is connected.

4. Before the test run, it is necessary to close the water supply valve, check the condition of each sealing valve, and do not leak or other conditions. When the pressure gauge pointer reaches the upper limit, the pump ends automatically. Open the water supply valve, you can supply water normally, if you need to supply water regularly, you can pull the selector switch to the manual part.

5. The automatic control system of electrical appliances must be waterproof and dustproof, and the insulation of the line must be checked from time to time, and the connecting bolts are not loose and the fuse is intact. The surface of the pressure gauge should be wrapped with transparent material as much as possible to avoid damage. 6. If the pressure tank has patent leather, falling off and other phenomena, it needs to be painted and maintained immediately, which will help to prolong the use time.

Hope mine can help you <>

Do you have any other questions?

What to do if the cracks of the plastic pressure tank leak What glue to use for the leakage of the pressure tank can be pasted with 502 super glue, 502 glue is used to bond porous and absorbent materials, and the effect of bonding steel, non-ferrous metals, rubber, plastics, wood, non-metallic ceramics and other items is very good. During the repair process, it is necessary to keep the surface of the tank dry, but if there is a large area of water leakage under pressure, it is best to replace the pressure tank with a new one. Precautions for kitchen water pipe renovation 1, water pipe diameter when transforming the kitchen water pipe, you need to know the pipe diameter to be changed, when replacing the water pipe, replace it according to the original pipe diameter, to avoid the inability to replace the noise, or the phenomenon of water leakage after the replacement is completed.

2. When the sewer pipe passes through the sewer pipe, ensure that the water pipe joint is used to seal the sewer joint, and if you need to replace the seal or other accessories, you must communicate with the owner. 3. The elbow of the water pipe is mainly used for water storage, and then the air in the sewer pipe is cut off, which helps to prevent odor or garbage from entering the water pipe and prevents the leakage of anti-odor. 4. The slope of the water pipe should pay attention to the slope of the water pipe, and the slope of the water pipe must be mastered, and the water inlet should be higher than the water outlet.

Be careful when installing sewer pipes, because there are no strict slope requirements for the pipes, you will not be able to get a suitable slope by raising the ground, and it will be difficult to launch the water later. 5. Pay attention to sealing. After the kitchen water pipe is deformed, it is necessary to pay attention to the sealing to prevent foreign objects from falling into the pipe during the next construction.

When cement falls on a pipe, it becomes a pipe. After curing, it is difficult to clean and can only be replaced, this treatment method is too cumbersome, and the sewer pipe must be dug up.

Cracks and leaks in the cement room can be repaired with cement mortar or glue.

1.Use cement mortar. First of all, it is necessary to chisel 10cm on both sides of the crack, and then clean the crack to avoid water or dust inside, and then apply a certain amount of cement mortar in the crack, which can effectively solve the cracks and leakage of the house.

2.Use glue. First of all, the garbage and dust in the area to be repaired should be cleaned invisibly, and then the crack needs to be made into a V-shaped groove with a depth of 1-2 cm using a pointed steel chisel.

Then use waterproof glue to evenly apply it to the crack surface, generally need to be brushed 2-3 times, and finally use a steel spatula to scrape the surface flat.

Summary. Hello, according to your problem description, the solution provided to you here is as follows: plastic pressure tank crack leakage can be pasted with 502 super glue, 502 glue is used to bond porous and absorbent materials, and the effect of bonding steel, non-ferrous metals, rubber, plastics, wood, non-metallic ceramics and other items is very good.

During the repair process, it is necessary to keep the surface of the tank dry, but if the pressure tank has a large area of water leakage, it is best to replace it with a new pressure tank.

Hello, according to your problem description, the solution provided to you here is as follows: plastic pressure tank crack leakage can be pasted with 502 super glue, 502 glue is used to bond porous and absorbent materials, and the effect of bonding steel, non-ferrous metals, rubber, plastic materials, wood, non-metallic ceramics and other items is very good. During the repair process, it is necessary to keep the surface of the tank dry, but if the pressure tank has a large area of water leakage, it is best to replace it with a new pressure tank.

Throw it away, repairing it is several times more expensive than buying a new one. Hehe.