When decorating, do you still need to continue to brush the water soaked wall tiles?

Updated on home 2024-07-17
22 answers
  1. Anonymous users2024-02-12

    Avoid hollowing and falling off, before brushing, be sure to clean the base surface to remove dust, oil, protective agent, release agent and other substances that affect the bonding, otherwise the bonding effect will be affected. The adhesive and the wall, the three-in-one adhesion, so that the three are firmly pasted together, therefore, the correct paste of the floor tiles on the wall, the wall is not brushed with wall tiles with adhesive, but with the wall solid, so that the pasted floor tiles on the wall are firm and not hollow. The porcelain tiles fired from clay, which is commonly known as soaking bricks, have high water absorption.

    There is no need to brush the adhesive on the back of the brick, just remove the film on the brick surface, put it in the brick pot, soak it until it does not bubble, soak it in water, and prevent the tile from falling off and paving on the wall.

    <> it is also difficult to absorb the moisture in the tile adhesive slurry, so as to ensure the moisture required in the mortar, so the tile does not need to be soaked in water before paving, and it can be directly pasted, and the construction efficiency of workers can also be improved. However, if you use glass glue or structural glue to stick it to the wooden wall, you don't need to soak it in water......The brick water absorption rate of the all-ceramic base embryo is low, do not need to soak in water, I don't know which kind of adhesive you are talking about, but do not need to soak in water, the brick on the cement wall needs to be brushed before the general tile paste....Well!

    This is also the case when the walls need to be sprinkled. Ceramic tiles will have more or less certain pores, soaking in water before paving, in order to make its pores fully absorb water, and porcelain tiles due to the density is larger, the porosity is much smaller, which makes the water absorption rate very low. All-ceramic tiles do not need to be soaked in water, the water absorption rate is very low, the water absorption rate of the tile does not need to be soaked in water when paving, but the need to brush the adhesive, with the tile adhesive can greatly improve the adhesion between the tile and the base layer, to prevent hollowing and falling off the problem, so as to ensure the water required for cement hydration in the mortar, so the tile paste does not need to soak in water.

    If the tile is accidentally soaked in excessive water, under the premise of not destroying the glaze of the tile, it can be air-dried and then used for tile adhesive construction.

  2. Anonymous users2024-02-11

    Personally, I don't think it's necessary to brush the adhesive on the soaked wall tiles, because I think it's a little redundant to do this, and it doesn't work to brush the adhesive after soaking in water.

  3. Anonymous users2024-02-10

    The brick wall soaked in water can no longer be brushed with adhesive, and it will definitely stick together after painting, which looks so unsightly, and the whole background looks ugly.

  4. Anonymous users2024-02-09

    It should not be necessary, after all, there is already water, and if you brush another layer of adhesive, it is very likely that it will not stick firmly, which will affect the final tiling effect.

  5. Anonymous users2024-02-08

    You need to continue to brush the adhesive, the most important thing is that this link is very important, so it should be done, and this is also a simple guarantee for the quality of the house, so every step can not be omitted.

  6. Anonymous users2024-02-07

    The soaked tiles must continue to brush the adhesive, it is impossible to paste the adhesive without brushing, when decorating, the requirements for sticking wall tiles are very high, and the requirements for adhesive are also very high.

  7. Anonymous users2024-02-06

    Absolutely. Continue to brush the water-soaked wall tiles with adhesive, so that they will stick more firmly and will not fall off in the later stage.

  8. Anonymous users2024-02-05

    Absolutely. Because this can make the wall tiles stronger, and the overall aesthetic sense is also better, and the service life is longer.

  9. Anonymous users2024-02-04

    Yes, the soaked wall tiles still have to continue to be brushed with adhesive, because this can make the wall tiles stronger, after all, it is to be used for a long time.

  10. Anonymous users2024-02-03

    Yes, they should be treated by some correct methods first, and then brushed, the time will be longer, and it will not affect some decorations.

  11. Anonymous users2024-02-02

    A: If it is a tile soaked in water, it does not need to be glued.

    You don't need to soak in water, because the adhesive is originally water-based, and you don't need to soak in water when you use the adhesive. The bricks that brush the adhesive are generally all porcelain, which does not need to be soaked in water, and the bricks that want to be soaked in water are not all porcelain bricks.

    If the glue is applied directly, there may be a risk of puncture, peeling or cracking. Water soaking brick refers to the brick that must be soaked in water, when laying tiles, in order to prevent the tile mortar from losing water due to high water absorption, so that the mortar can not play a normal bonding role.

    The tile can be pasted without soaking in water and directly brushing the adhesive.

    The bricks that brush the adhesive are generally all porcelain, which does not need to be soaked in water, and the bricks that want to be soaked in water are not all porcelain bricks.

    It should be completely moistened, but there should be no open water.

    Glue the tile with a toothed scraper.

    Apply evenly on the wall and the back of the tile, and ensure that the angle between the toothed scraper and the base surface is consistent in the scraping. The ratio of high-quality glue is scientific, the stirring is sufficient, and the powder is relatively uniform. After the glue is completed according to the proportion, it is also necessary to add water and stir.

    Extended information: The introduction of tile brush adhesive is as follows:

    Generally speaking, whether it is paving tiles.

    To return the wall tiles, the master will soak them in water and directly use cement mortar.

    Paving is sufficient. It is necessary to observe its viscosity, if it is a high-quality glue, it feels like a thick slurry when stirred, because it contains various functional additives, which can strengthen the adhesion of ceramic tile glue, if the glue is relatively thin, it is not a high-quality glue.

    Tiles are all absorbent, while full tiles are not. If you use cement mortar to pave the whole tile, there will be a hollow.

    The probability of falling off is very large, and the tile adhesive is a cement binder composed of polymer, the special formula is suitable for almost all kinds of tiles, and maintains good water retention, and the probability of hollowing off is very low.

    Thank you for your inquiry.

  12. Anonymous users2024-02-01

    It is better to use adhesive when pasting tiles, because the coagulation power of adhesive is very strong, regardless of the high or low water absorption rate of tiles, it can avoid hollowing or even falling off. When the tiles soaked in water are on the wall, it is difficult to construct, and if they are not soaked through, there will be hollowing and falling off in the later stage.

  13. Anonymous users2024-01-31

    The brush adhesive is better, which can effectively prevent the phenomenon of tile hollowing, and is more suitable for tiles that do not absorb water.

  14. Anonymous users2024-01-30

    In fact, it should be better to use by soaking, and the service life is relatively long.

  15. Anonymous users2024-01-29

    Hello, my house is decorated, the wall is painted on the wall, and the adhesive and tile adhesive will not fall off the tiles.

    Hello, my house is decorated, the wall is painted with the wall fixed in the brush adhesive and the porcelain wheel brick glue together will not drop the tile: after the wall is brushed, you can not directly paste the tile, because it is easy to fall, you need to do a good job of waterproof and brushing treatment, before you can paste the tile. The general process steps are that after waterproofing, it must be brushed, otherwise the tiles will not be firmly pasted, and they will fall down after a long time.

    Some people also say that the use of tile paste instead of cement mortar, that is, the so-called new thin paste method, does not need to do brushing treatment, such a statement is incorrect. The construction practice is: whether it is a new thin paste method or a traditional paving method, it is necessary to first carry out the base treatment and hair wax letter of the wall.

    After brushing the wall, the brushing needs to be dealt with, because the smooth wall tiles are not very stable and firm, otherwise it will affect the overall aesthetic effect.

  16. Anonymous users2024-01-28

    As we all know, tiles are generally used for water.

    Attack mud mortar, but in recent years, there have been more du tile adhesives on the market, and I don't know which one is better to use!

    Let's look at the cement mortar first, that is, it is mainly cement, add yellow sand and some waterproof additives, and then stir with water, which is basically zero pollution, high adhesion, and preferential treatment.

    But the bad thing is that cement mortar is affected by many external factors and is easy to fall off. In addition, the hardness of tiles on the market is getting higher and higher, and the focus is on poor water absorption, so the tiles often fall off.

    From the appearance, tile adhesive and cement are almost the same, mainly mixed with water, and then directly used to paste tiles. However, tile adhesive has an advantage that cement does not have, that is, it is less affected by external factors, and it is resistant to low temperature and water. The bad point may be that it is expensive, and there are many bad tile adhesives on the market, and there may even be the problem of excessive formaldehyde.

    Compared with cement and tile adhesive, the adhesive performance of ceramic tile adhesive will be better, the point is that you don't need to run the tile in advance, you can paste it directly. There is no need to paint a thick layer on the wall, and it is basically very firm when pasted on.

    Of course, good things are generally expensive, so there is no need to use tile adhesive in all places, you can use it in the kitchen and bathroom, because these places are often wet, and it is easy to fall off with general cement.

  17. Anonymous users2024-01-27

    After applying adhesive to the fully tiled wall, you can do without tile adhesive. Because tile adhesive is a material used to process tile backing when specially pasting. The back of the treated tile can be directly bonded with cement mortar without the use of tile adhesive.

    Tile adhesive can be used in combination with a variety of adhesive materials to form a tile bonding system, which greatly improves the adhesion between ceramic tiles and the base layer. This tile adhesive has good performance in standard concrete slabs and glazed tiles, which greatly improves safety.

    The adhesive is specially used for the back treatment of wet vitrified tiles, which can effectively improve the bonding strength of vitrified tiles and adhesive materials, and solve common problems such as hollowing and falling off of wet vitrified tiles. It is suitable for the back treatment of bricks with low water absorption, dense texture and smooth surface such as stone.

  18. Anonymous users2024-01-26

    You can use tile adhesive to brush the wall, tile adhesive is a rigid product can not change with the thermal expansion and contraction of ceramic tiles and walls, ceramic tile adhesive is a flexible product, can change with the thermal expansion and contraction of tiles and walls. Therefore, the tile adhesive is more resistant to thermal expansion and contraction and vibration.

  19. Anonymous users2024-01-25

    Generally speaking, there is no need to brush the wall after brushing the adhesive, but the premise of the wall not being brushed is that the original wall is "not smooth", and if the original wall is smooth, it still needs to be brushed. I have been engaged in the decoration industry for more than ten years, and the design and construction are practiced first-hand.

  20. Anonymous users2024-01-24

    The so-called need to dip.

    To soak the tile, the use of clay tiles, because of its BAI water absorption is relatively large, so in order not to make the zhi paving mortar dao slurry lose water, resulting in the mortar can not play its due bonding role, so the tile needs to be fully soaked in water before paving, and take out to dry the paving.

    As long as it is a tile that needs to be soaked, even if the tile adhesive is used to pave, the tile still needs to be soaked, otherwise there is a hidden danger of hollowing out the shell.

  21. Anonymous users2024-01-23

    The floor tiles on the wall are used as wall tiles without soaking in water, and the back of the bricks can be constructed by brushing the layer of adhesive.

  22. Anonymous users2024-01-22

    Summary. Generally speaking, the tile soaked in water cannot be brushed with adhesive, because it is not all-porcelain, and there is no need to brush another layer of adhesive. For all-porcelain tiles, it is not advisable to choose cement mortar to pave, because it is easy to hollow out in the later stage, and it will be detached in serious cases.

    Therefore, before paving, all-ceramic tiles must be brushed with a layer of adhesive before entering the paving.

    When decorating, do you still need to continue to brush the water-soaked wall tiles?

    Generally speaking, the tile soaked in water cannot be brushed with adhesive, because it is not all-porcelain, and there is no need to brush another layer of adhesive. For all-porcelain tiles, it is not advisable to choose to use cement mortar to pave the orange, because the post-code period is prone to hollowing, and it will be detached in serious cases. Therefore, before the all-ceramic tile is paved, it must be brushed with a layer of adhesive reeds before entering the paving.

    This is my answer, I hope it is helpful to you, thank you <>

Related questions
16 answers2024-07-17

Bricks, fashionable atmosphere on the grade, give people a bright feeling, the living room and balcony paving the same deliberate distinction will have a great sense of separation. Each area distinguishes the type and color of ceramic tiles, which is also a misunderstanding of many people when choosing tiles. There are a few bathrooms to distinguish a few colors, plus the kitchen, balcony, a set of seven or eight kinds of tiles in the house, in order to pick a different tile, how to look at it does not match, even if the living room is paved with tiles, try to choose light pink or beige pattern tiles, so that the layers are clear, the overall decoration effect is good. >>>More

18 answers2024-07-17

For the soaking bricks to the wall, cement mortar is used. >>>More

16 answers2024-07-17

load-bearing walls. As the name suggests, it is something that bears weight, supports the upper wall, and determines the safety of the room. In the renovation and decoration of houses, the judgment of load-bearing walls is very important. >>>More

16 answers2024-07-17

When decorating the house, if the size of the house allows, there is a utility room, which is great! >>>More

28 answers2024-07-17

Collapse. As the name suggests, the load-bearing wall bears the weight and is the main structure of the building, and the destruction of the load-bearing wall at will will have potential safety hazards, resulting in fracture or collapse.