How to install and debug the hinge Hinge installation precautions

The hinge is composed of two hinge seats, which in turn are composed of a circular part and a connecting body, and are composed of three connecting plates perpendicular to each other. Because it is a three-sided structure with three interperpendicular plates, it belongs to a stable structure according to the principle of trigonometry in mathematics. Due to the relatively large area of the connected contact surface, the connection strength between the connecting body and the structural part is high.

The installation of hinges can be specifically divided into the following points:

First, before installation, it should be observed whether the hinge is consistent with the conveying equipment and the parts that need to be connected;

Second, in checking whether the hinge connection surface is matched with the connected object, whether it matches in length, width and thickness, when sharing a side plate, the total clearance required should be twice the minimum clearance, and when the coverage distance of the fixed machinery is reduced accordingly, the hinge with the bent arm needs to be adopted. When the edges are filleted, the minimum clearance is reduced accordingly, and the minimum clearance required can be found from the corresponding table for each different hinge;

Thirdly, the connection mode of the observation hinge should match the installed object, and the width, height and material quality of the machinery are determined according to the factor of the number of hinges required by the machinery;

Fourth, check whether the hinge and the screws and fasteners connected to it are matched, and the maximum size available for each hinge is to select the hinge according to different conveyor categories;

If the two pages of the fifth hinge are not symmetrical, it should be distinguished which page should be connected to the fixed object and which page is connected to the other end, the greater the distance, the smaller the minimum clearance, and the distance between the hinges should be as large as possible for the sake of stability;

Sixth, when the hinge is installed, it should be ensured that the hinge is on the same vertical line as the fixed object, so as to avoid the dislocation of the mechanical object or the wear of the conveyor due to the instability of the fixation.

Generally, after the hinge is manufactured, its damping force has been adjusted, and the damping force of the hinge can be adjusted through the laptop screen.

When installing the laptop hinge, you need to follow the correct hinge assembly process, and the fixing hole provided by the hinge needs to be installed in place, otherwise it will affect the opening and closing of the notebook, and you cannot use heavy objects to knock, which is easy to cause the hinge to break and deform.

Hinges are common hardware in home life, and hinges will be found in wardrobes, cabinets, doors and other places. As the main accessory of the cabinet door, the hinge plays a decisive role in the use of wardrobes, cabinets and doors. Hinges are attached to the door, so how do you install the hinges?

Introduction to hinge mounting methods.

Hinge installation method:

1) Before installation, check whether the hinge and the gate and window frame and sash are matched.

2) Check whether the hinge groove matches the height, width and thickness of the hinge.

3) Check whether the hinge and the screws and fasteners connected to it are matched.

4) The connection of the hinge should match the material of the frame and the sash, such as the hinge used in the steel frame wooden door, the side connected with the steel frame is welded, and the side connected with the wooden door leaf is fixed with wood screws.

5) In the case of asymmetry of the two pages of the hinge, it should be distinguished which page should be connected with the sash, which page should be connected to the gate and window frame, one side connected with the three sections of the shaft should be fixed with the frame, and one side connected with the two sections of the shaft should be fixed with the frame.

6) When installing, it should be ensured that the shaft of the hinge on the same leaf is on the same plumb line, so as to avoid the door and window sash from snapping.

Hinge installation precautions.

1. Minimum clearance.

Minimum clearance refers to the minimum distance required from the side of the door to open the door. The minimum clearance is determined by the c-distance, the thickness of the door and the type of hinge. When the door edge is rounded, the minimum clearance is reduced accordingly. The minimum clearance required can be found from the table corresponding to each of the different hinges.

2. The minimum clearance of the half-cover door.

When two doors share a side panel, the total clearance required should be twice the minimum clearance so that both doors can be opened at the same time.

3. c distance.

c Distance refers to the distance between the edge of the door and the edge of the hole in the hinge. The maximum C size available for each hinge varies depending on the hinge model. c The greater the distance, the smaller the minimum clearance.

4. Door coverage distance.

Door coverage distance refers to the distance at which the door covers the side panels.

5. Clearance.

Clearance refers to the distance from the outside of the door to the outside of the cabinet in the case of full cover; In the case of a half-cover, the distance between two doors; In the case of an inside door, the clearance is the distance from the outside of the door to the inside of the side panel.

6. The number of hinges required for each door.

The width of the door, the height of the door, and the material quality of the door are the determining factors for the number of hinges required for each door. In practice, the various factors that arise vary depending on the situation. Therefore, the number of hinges listed in the figure above can only be used as a reference.

When the situation is unclear, it is advisable to do a trial. For stability reasons, the distance between the hinges should be as large as possible.

The above is the detailed installation method of the hinge, as well as the special matters that need to be paid attention to during the installation process. The correct installation of the hinges can ensure the normal use of the door. Consumers can follow the above methods or refer to the attached instructions for use.

Door hinge is a more common part, it plays a role in fixing the door, no matter how good the parts also need installation skills, sometimes because of improper installation skills, resulting in the opening of the bad bridge when the door is not smooth, today I want to share with you is the door hinge installation skills to eliminate brother and what are the precautions when installing.

Door hinge installation tips.

1.Minimum clearance.

The gap refers to the gap on the side of the door when the door is opened, the gap is determined by the thickness of the door and the hinge type, and what kind of hinge type is needed can be compared by each different angle.

2.Minimal gap in the half-covered door.

When two doors need to use one side panel, the total gap is twice the minimum gap, so that both doors can be opened at the same time.

Distance. The meaning of C distance refers to the distance between the door side and the plastic cup hole, the maximum size of the general hinge is C ruler, according to different models, the wider the C distance, the smaller the gap.

4.Door coverage distance.

The distance the door covers is the distance at which the side panels are covered.

5.Interval. The meaning of the gap refers to the distance between the outer edge of the frame and the outer edge of the door when it is fully covered, and the gap refers to the distance from the outside of the door to the outside of the cabinet in the case of full cover; In the case of a half-cover, the distance between two doors; In the case of an inside door, the clearance is the distance from the outside of the door to the inside of the side panel.

What are the precautions when installing.

1.Pay attention to the installation location and quantity.

The door at home is heavier, it is recommended to use three hinges, generally ordinary doors with two hinges is enough, it should be noted that the corners of the door and window sash can not use hinges, should be installed in the door and window sash body one-tenth of the place, to avoid evenly divided into 3 parts, should be used on the two, the next form. Prevent door imbalance.

2.Prevent falling fans.

In the door hinge installation skills, the falling fan is the most critical, it refers to the skill problem when installing the door, so that the upper and lower levels slowly widen, and the gap below slowly narrows, resulting in the opening and closing of the door is not smooth, and even the door will fall, generally this situation is caused by the selection of hinges with different specifications.

3.Grasp the gap distance.

In order to make the appearance of the door look good, be sure to grasp the distance between the door panel and the hinge, the normal gap is generally 3-5 mm.

4.Make sure the accessories match.

The specifications of the hinge are very important in the door hinge installation technique, and it must be matched according to the thickness, length and width of the door.

The hinge installation method is as follows:

1. Insert the hinge into the base, and then gently press the hinge arm with your fingertips, and at the same time, you can hear a "click", indicating that the hinge arm is safely hooked to the hinge base through five fulcrums. In principle, the quick-release process is done by crossing the door from top to bottom, with the uppermost hinge taking on the entire weight of the door.

2. In order to enhance the storage function of the kitchen, it is indispensable to design some tall cabinets, some of which are cabinets with open doors, and this kind of cabinet is also inseparable from the hinge of the turning Li Chong plate. Hinges can be installed on the upper flap and side panels respectively, so that the flap can be added at the end, which brings a lot of convenience. Hope mine can help you.