What to do if the refrigerator seal is not tight, what to do if the refrigerator seal is not tight

Steps to replace the refrigerator door seal: first take out the magnetic strip in the original old door seal, you can first adsorb it on the refrigerator body to avoid damage or the possibility of breaking, then remove the original old seal, replace the new door seal, and finally embed the magnetic strip that was just taken out into the new door seal. It is generally caused by the following reasons:

1. The door seal is aging, because the refrigerator door is opened and closed very many times, which makes the refrigerator door seal almost always live in a state of stress, and if it is in such a state for a long time, the door seal is easy to age, deform, etc., so that the refrigerator door will not be closed tightly. 2. The suction power of the refrigerator door is not large enough, and most of the refrigerators on the market now use drawer design, which solves the problem of children's opening and closing the door, but once this technology is not too hard, it is easy to cause the refrigerator door to loosen, so that the refrigerator door is difficult to close tightly 3. Improper maintenance of the refrigerator, in fact, the refrigerator is the same as people, and it should be properly maintained frequently, and if it is not properly maintained for a while, or it has never been maintained, it will make it sick, and the problem of the refrigerator door is not closed tightly 4, it is very important to clean the refrigerator correctlyFor the treatment of the refrigerator, not only the inside of the refrigerator can be treated, but also the outside of the refrigerator should be cleaned frequently, otherwise once too many stains are deposited on the outside of the refrigerator, the refrigerator will not be closed tightly, and the door seal should be cleaned regularly and correctly.

It is recommended to try the first one.

1. Soak in hot water. If the refrigerator seal is deformed, then we can remove it, and then put the deformed part into the prepared hot water to soak, soak for about 1 minute or soak out, and at the same time place it on a flat countertop, gently straighten it.

2. You can also use a hair dryer to blow hot air to blow up the bad seal of the refrigerator door, and it will be good after cooling. The hair dryer should not blow for too long, the distance should not be too close, and the temperature should not be too high.

You can change it, I suggest you go to Toshiba** to see, hit ** to try.

Things are no longer produced, but after all, they are big factories.

My pot, that is.

We will all notice that there is a sealing strip on the door of our refrigerator, but don't underestimate its role, the refrigerator sealing strip is the goalkeeper of the refrigerator, if the sealing strip is not tightly sealed, the effect is not good, you need to do some treatment. Today, I will introduce to you what to do if the refrigerator seal is not tight, some tips and solutions are here!

1. Introduction to refrigerator seals.

Refrigerator door seals are made up of two parts, one is a soft polyvinyl chloride (SPVC) jacket and the other is a magnetic adhesive strip. The PVC jacket is processed from raw materials through extrusion. The shape varies depending on the product, model, and design.

It is divided into different shapes, heights, and lengths. The purpose is to match the design of the refrigerator, and the magnetic strip is made by combining magnetic materials and plasticizers, extruding and magnetizing. This kind of door seal can also be used for disinfection cabinets, water dispensers, display cabinets, etc., and its sealing and insurance functions.

Second, the refrigerator seal is not strict, how to dismantle the travel office.

1. Remove the refrigerator door from the box, take a sharp knife and cut the bonding place of the four corners of the door seal and the imperial book.

2. Take out the plastic magnetic stripe from the refrigerator door seal and still suck it on the box.

3. Put the removed door seal into a basin filled with 55-65 degrees Celsius hot water and soak it for 4-6 minutes, pinch the two ends of the door seal with your hands, and force the uneven part of the door seal to be straightened (the tension should not be too large, so as not to break it) and then put it on the flat glass, and then press it with glass on it, and after it cools naturally, the door seal will become flat and straight. If this does not work, repeat it several times until the bumps disappear.

4. Due to the stretching, the length of the door seal after the above treatment is slightly longer than the original. Therefore, the excess part should be cut off according to the original length and the end should be cut at a 45-degree bevel.

5. According to the opposite procedure of disassembly, the magnetic stripe is loaded into the door seal, and then the door seal is put back to its original place, and the four corners of the door seal are glued with 502 glue.

Third, the refrigerator seal is not tight.

1. Turn the refrigerator door seal up, remove all the screws that fix the door seal one by one with a ten-blade stool screwdriver, and then pull the door seal away from the door liner and remove it.

2. When installing, first put the door seal around the door liner, and then attach it to the inner side of the door, align the original fixed hole, fix it with screws on the upper side, and then tighten the screws on the diagonal position. Before tightening the screws, pay attention to the flat and position of the door seal.

3. Close and open the door after installation, and check the sealing between the door and the box. If the seal is not good due to poor installation, the screws of 2-3 where the door seal of the defective part is located should be loosened for adjustment.

4. If it is caused by the deformation of the door seal, it can be heated by a hair dryer for shaping. If the four corners of the door seal are not well sealed, the door seal at the corner can be turned up and filled with an appropriate amount of styrofoam.

5. After the installation is completed, the door opening and closing experiment should be carried out several times to test whether it can be opened and closed freely.

The above is what to do if the refrigerator seal is not tight, I hope it will help you.

The treatment method of the refrigerator seal is not as follows: banquet sedan chair rock

Tools Materials: refrigerator seal, washbasin, warm water, baking soda, dish soap, toothbrush, water.

1. Remove the refrigerator seal.

2. Prepare a basin, add warm water about 40 degrees Celsius in it, two spoonfuls of baking soda, squeeze in a small drop of dish soap, stir it well, and then put the sealing ring into warm water and let it soak for 10 minutes.

3. Prepare a waste toothbrush, gently scrub along the gap of the refrigerator, and the stains will be all gone. Finally, rinse again with water. Place on the balcony to dry.

4. After such cleaning, the refrigerator sealing ring is not the same as new, and after soaking in warm water, it becomes more soft and soft. Put it back in now.

5. Align the 4 corners of the refrigerator, and then press it into it by hand in turn, so that the refrigerator sealing ring is firmly installed back, and finally check whether there are any gaps.

Refrigerator seals are not tighter solutions:1. The refrigerator sealing strip is not strict because of the air leakage phenomenon of the sealing strip, at this time, the air outlet of the hair dryer should be aligned with the air leakage position of the sealing strip, and then open the hot air gear for hot blowing, when the air leakage position is blown up, the hot blowing can be stopped, and when the temperature of the sealing strip is cut down, the refrigerator door can be closed tightly. It should be noted that the heat blowing time should not be too long, the distance should not be too close, and the temperature should not be too high.

2. The refrigerator seal is not tight, and it may be caused by the deformation of the seal, so the seal should be removed, and then soaked in 60 degrees of hot water, soaked for about eight minutes, and then taken out and placed on a flat countertop, and then straightened the seal, and finally reinstalled the seal on the refrigerator door.

3. The refrigerator sealing strip is not tight, which may also be caused by iron filings sticking to the sealing strip, so as long as you use a brush or rag to wipe the iron filings or metal powder clean.

The seal on the refrigerator door does not seal the solution:

1. Soak in hot water.

The common reason why the refrigerator seal is not sealed is that it is deformed, and as long as the shape of the refrigerator seal can be restored, it can be restored to normal functional use.

2. Blowing and shaping.

Using the hot air of a hair dryer, blow the deformed part of the refrigerator seal, reshape it, and then it can be used normally.

3. Eliminate iron filings.

The refrigerator seal will be stained with some iron filings or dirt when used for a long time, which will cause a gap between the refrigerator and the seal, resulting in a loose seal, just remove these things.

4. Replace the sealing strip.

If the refrigerator seal itself is not sealed due to aging, you can only choose to replace the refrigerator seal with a new one.

1. Blowing and shaping. When the refrigerator seal is not tight, you can use an electric hair dryer to use hot air in the place where the refrigerator is not well sealed, but pay attention not to blow for too long and make the seal soft. If the temperature is too close or too high during the blowing process, it is easy to damage the sealing strip.

2. Soak in hot water. When the refrigerator seal is deformed, you can remove it, and at the same time soak the bird-shaped part of the refrigerator hole in hot water at about 60 degrees Celsius, remove it for 7-8 minutes, and place it on a flat countertop and gently straighten it.

3. White rubber sealing. If the refrigerator seal is slightly deformed, you can loosen the screws that fix the door seal of the refrigerator, and at the same time insert the white rubber at the crack gap, and then re-tighten the screws.

4. Eliminate iron filings. If there are some iron crumbs or metal powder sticking to the refrigerator seal, the refrigerator door will not be closed tightly, so use a brush or rag to remove the iron filings.

The above is still about the method of what to do if the refrigerator seal is not tight, if the refrigerator at home also has such a situation of not being tightly closed, you can deal with it according to the above method.