What should I do if it rains when the automatic waterproof sticker is applied? What can go wrong? Do

In this way, the waterproof effect may not be so good, it will be easy to degum, there is a leakage, it is best to re-pave, which will be safer, so as not to cause more trouble when the waterproof effect is not good.

It is recommended to re-paste, automatic waterproof paste on the base layer requirements are relatively high, the base layer is dry and clean, after the paving needs to be naturally bonded in a dry situation to achieve the waterproof effect, if the rain in the process of paving the effect will not be ideal, maybe it can still be waterproof for a period of time but it is easy to leak after the quality problem is short, so it is recommended to re-pave when the weather is fine.

It is necessary to suspend the paste, or find a shelter in time, it may seep water, if the area of the paste is small, it is recommended to re-paste.

Use a tarp to cover the area that has already been laid out. The problem is that getting wet without drying out can damage the waterproof sticker. There is no need to repave immediately, you can look at the situation first, and you can continue to pave if it is not serious.

Hello, in this case, the first is to immediately cover with a canopy to prevent water ingress, and the second is to see if there is water leakage and seepage in the place where the membrane is paved after the rain, and repair it immediately if there is one. The use of Sino YYPE polymer waterproofing membrane adhesive has the characteristics of high compression, strong adhesion and impermeability. I hope it will be adopted, thank you.

The waterproofing membrane is generally bonded by the hot melt method, so as long as the construction is not affected by freezing and rain, after a period of time after construction, the membrane has cooled and firmly bonded to the base surface, rain and freezing will not affect the quality, you can wait for the weather to be good and then do the protective layer, the protective layer is to protect the membrane from external damage and enhance the waterproof years and set up.

Self-adhesive waterproofing membrane is a kind of self-adhesive high-quality waterproof material, the matrix is composed of polymers, and the current market is mainly based on asphalt or modified rubber as the main body, and additives are physically dispersed to form a multi-component solid mixture.

Precautions: 1. Do not use non-exposed coils in an exposed environment.

2. Do not pave self-adhesive coils on the frozen base surface.

3. It cannot be constructed on the base layer that is polluted and has a high moisture content.

4. The packaging and isolation paper of the self-adhesive coil can only be removed before and during the paving.

5. When the sealant is not used up, the container should be tightly tightened in time.

6. Supporting materials from other manufacturers should not be used in this product without verification.

It won't make much of a difference. Generally, it takes 24 hours for the waterproof layer to work properly. If there is too much water, it will seep in, and a small amount of water will be collected inside, but the problem will not be particularly serious.

Introduction

Waterproofing layer: A layer of material designed to prevent rainwater from entering roofs, groundwater seeping into walls, basements and underground structures, indoor water seeping into floors and walls. If it is made of waterproof slurry, it is generally not afraid of rain after three days, and if it is made of waterproof membrane.

Generally, when making a waterproof layer, special attention should be paid to the treatment of the base layer. It's not treated like everyone thinks, as long as we buy the materials. If the base layer is not treated well, no matter how good the material is, it cannot guarantee the waterproof effect.

Therefore, we must pay attention to the quality of the base layer, which plays an important role in waterproofing. When doing waterproofing, the requirements for the base layer are no sand, no cracks, smooth, and hollow.

It's okay, it's all a minor issue.

If there is a lot of water in the insulation layer and it is not drained, it will be troublesome in the future. Even if the waterproof layer is done, when it rains again, the water in the insulation layer will be pressed down, resulting in water leakage. Therefore, it is best to let the water on the roof dry before making a roof waterproofing layer.

As long as the waterproofing is done well, there will be no problem

3.Basement waterproof structure.

At present, there are two types of waterproofing measures adopted: membrane waterproofing and concrete self-waterproofing.

1) The membrane is waterproof.

There are two construction methods for membrane waterproofing: external waterproofing and internal waterproofing. When the membrane waterproof layer is located on the outside of the underground engineering envelope structure (i.e., the water front), it is called external waterproofing, and the waterproof effect of this method is better; When the membrane is pasted on the inner surface of the structure, it is called internal waterproofing, and the waterproof effect of this method is poor, but the construction is simple, easy to repair, and it is often used in repair projects.

External defense and external sticking method: first of all, a permanent protective wall is built around the concrete cushion of the plastered cement mortar leveling layer, the lower part of which is dry-paved with a layer of membrane as an isolation layer, and the upper part is built with lime mortar masonry temporary protective wall, and then the plane is paved first, and then the façade is paved, and the flat and elevation should be crossed and lapped. After the waterproof layer is paved, the protective layer construction shall be carried out immediately after passing the inspection, and then the main structure construction shall be carried out.

After the completion of the main structure, the temporary protective wall was dismantled, and the waterproof layer of the exterior wall was made. The structure is shown in Fig. The membrane waterproof layer is directly pasted on the outer surface of the main body, and the waterproof layer is synchronized with the concrete structure, which is less affected by the settlement and deformation of the structure, and it is not easy to damage the waterproof layer during construction, and it is also convenient to check the waterproof quality of the concrete structure and the membrane, and the problem is easy to repair.

The disadvantage is that the waterproof layer needs to be constructed several times, the process is more, the construction period is longer, the working face needs to be larger, and the amount of earthwork is large, the amount of template is more, and the membrane joint is not easy to protect, and it is easy to affect the quality of waterproof engineering.

This has no effect, don't worry, the water can't get in, just spread a part.

If this is the case, it is best to cover it all over, because it will definitely affect it more or less if it rains.

As long as the construction is finished.

There is no impact.

This is a hot melt type of construction.

It's okay.

If it rains partially, of course, it will have an impact on its waterproof effect, which is the worst.

Because you're only partially paved, and it's raining heavily, it's definitely going to have an impact, and if you're done and then wait a while, that's fine.

Generally, if this kind of rainstorm is used, the impact should not be particularly large, you can check it.

Except for some of the rains, it may be a little bit of an impact.

Modified and pasted a part of the waterproof roll and it rained heavily, which was influential.

If you put a part of the waterproof roll and it rains heavily, of course it will be affected, and it will leak.

As you said, although I'm not waterproof, I see that they do just that, and they must dry before laying the membrane. The following is found online, after all, I am not a professional

Find a tarp to cover, the base mortar of outdoor floor tiles is generally dry and hard mortar, and rainwater infiltration will cause changes in the density of the mortar, affecting the quality of survival.