What are the reasons for the slow molding of beauty sewing agents?

The low temperature viscosity increases: because the sewing agent is a polymer material, it is generally constructed in the cold winter, and the external environmental temperature is low, and the viscosity will become larger, so that the glue is laborious. At this time, we can soak the sewing agent in hot water to preheat it to reduce the resistance of gluing.

The moisture in the gaps can't escape, and then it reacts chemically with the sewing agent, and it will not solidify today.

Because the inside of the glue bocal is spiral-shaped, the sealant consists of a mixture of three raw materials. When the three raw materials pass through the hose, these advantages of the sealant are of course true because of the spiral paper, but if the sealant falls off, these advantages disappear in an instant. At this point, you may regret not doing a traditional sealant.

Seam beauty agents usually consist of two ingredients, one is the material and the other is the healing agent. In this case, we can only remove the applied sealant without curing it and then reapply the sealant with a healing agent. In addition, there is no other way, so it is usually because no healing agent is added, if it is caused by the small angle of rotation of the material control valve, just open the angle of the valve slightly and try the gun again.

If the opening of the applicator air pressure control button is too small, the epoxy seal arm will not**.

The air humidity is high, and the sealant absorbs water, which will affect the curing of the material itself. The ratio of healing agent to pigment is wrong, and if it is found after 72 hours that it has not dried, it can be removed immediately and reformulated. If it is a high-quality articulated material, it is relatively viscous, uniform, thin and shiny, does not sag on the wall, does not collapse during soil construction, and can be filled evenly and completely.

If the sealant does not dry, it mainly depends on external factors that affect the drying of the sealant, such as ambient temperature and ventilation conditions. Low temperatures, low ventilation can lead to longer drying times of the sealant, if not these two problems, it depends on the problem in construction, whether it is the addition of water or the high moisture content of the base surface.

The reasons for the slow molding of the sewing agent are uneven mixing, poor quality of the sewing agent, low indoor temperature, too humid indoors, and a lot of dust in the gaps.

Summary. Dear, hello, I am glad to answer for you whether the time of drying of the sewing agent is slow or fast, whether it is good or not, whether it is good or not depends on the speed of drying, it is better not to be fast or slow. The real best sewing agent does not dry slowly or fast, and fast or slow drying indicates that there are some problems with the material.

After the sewing is completed, a curing time is required for the material, and the curing time is related to the brand, temperature and humidity. If the indoor temperature is low or humid, there will be a situation where the sewing is not cured or the sewing is too slow, especially in winter, the curing time is longer.

Dear, hello, I'm glad to rent a state source to answer for you whether the time to dry the sewing agent is slow or fast, and whether it is good or not depends on the speed of drying, it is better not to be fast or slow. The real best beauty sewing agent does not dry slowly or fast, and fast drying or slow drying quietly indicates that there are some problems with the material. After the completion of the sewing and filling, it is necessary to have a curing time for the material, and the curing time is related to the brand, temperature and humidity.

If the indoor temperature is low or humid, there will be a situation where the sewing is not cured or the sewing is too slow, especially in winter, the curing time is longer.

Dear, if my answer is helpful to you, please also give a thumbs up (comment in the lower left corner), look forward to your like, your efforts are very important to me, and your support is also the driving force for my progress. If you feel that my answer is still satisfactory, you can close the void reed and click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

The beauty caulk is a new type of caulking product, is an upgraded product of building material caulk, composed of polymer and high-grade pigments, which solves the problems of traditional caulk easy to be dirty and black, cracking, etc., after use, it can make the tile not dirty and not black, waterproof and stainproof, even if it is dirty, it will be clean when wiped, understand its advantages while talking about its shortcomings. The beauty caulk is a new type of caulking product, is an upgraded product of building material caulk, composed of polymer and high-grade pigments, which solves the problems of traditional caulk easy to be dirty and black, cracking, etc., after use, it can make the tile not dirty and not black, waterproof and stainproof, even if it is dirty, it will be clean when wiped, understand its advantages while talking about its shortcomings.

What are the disadvantages of beauty sewing agent:

1. Construction defects

Because the beauty sewing agent is only a variant of the one-component acrylic sealant, the wear resistance is very poor, and it can only be used when the base is laid, which is much lower than the ceramic tile and will not be rubbed. But the disadvantage of this is that it is easy to hide dirt and dirt.

Moreover, for microcrystalline stone, polished glazed bricks, and vitrified tiles, its concave surface makes the feet feel unpleasant. In particular, some small gaps, such as gaps of about 1mm, make it impossible to bond to the surface at all.

3. Performance defects

The adhesion is insufficient, when the tile is not relatively flat, when the four seasons are found to shrink, the beauty joint agent and the tile gap façade are easy to crack, and the performance is that the beauty joint agent peels and falls off. Because the nature of the sewing agent determines that it cannot withstand water for a long time, the environment of toilets, kitchens, etc., which is easy to come into contact with water, and aging is very fast. The wear resistance is poor, if you test it according to the standard of tile grout, use the wear resistance testing machine, and white corundum, and it will be worn away before it arrives.

Compressive strength, flexural strength, and shrinkage value are not the four major indicators, and only the water absorption rate can be passed. Therefore, it can only be called beauty grout, which cannot be counted into the category of tile caulk, and there is no national standard.

4. Short service life

At present, most of the domestic tile joints are made of caulk or grout, although economical, with the progress of science and technology, the beauty of the joint agent has entered people's lives, but the common beauty of the market has a low technical content, short service life, it is about three or two years, the cost performance of the beauty of the joint agent is higher, it makes up for the shortcomings of the type (the same industry in China are type), it has a unique formula, rich color, flexible collocation, containing antibacterial ingredients, is under development.

The beauty sewing agent has entered people's lives and has been recognized by everyone, is to solve the problem of dirty ceramic tiles and "tailor-made" a building materials decorative materials, but the common beauty sewing agent on the market due to low technical content, a characteristic of the beauty sewing agent is to make the tile gaps never dirty black! The above knowledge description may be helpful to you.

1. Check whether the rotation angle of the material control valve is too small, and open the valve angle slightly larger.

2. If the opening of the air pressure control knob of the glue gun is too small, it will also cause the epoxy sewing agent glue gun to fail to make materials, and the knob can be rotated along the direction indicated by the reading cong of the + sign.

3. To see if the glue head of the glue gun is blocked, you can use a steel needle or a fine iron with a burning wire to gently open the hole, or clean it directly.

4. The raw materials of the sewing agent are too thick, if the temperature is very low, the colloid may be frozen, and the old cherry agent can be properly warmed.

5. If the sewing agent is placed for too long, it will also cause the phenomenon of difficult to beat.

Compared with the traditional caulk, the sewing agent is naturally very good, and there are many advantages: it is as hard as porcelain.

Wear-resistant, scrub-resistant, waterproof, mildew-proof, non-blackening, non-falling off, non-collapsing, but in fact, the sewing agent is also water-based and oil-based. So what's the difference between them?

1. Environmental protection:

First of all, the sewing agent is made of epoxy resin and pigment as the main ingredients, and the epoxy resin in the water-based porcelain sewing agent is water-based, with water as a diluent, without benzene, low aromatic hydrocarbons and other organic solvents and formaldehyde, lead and other heavy metal compounds, there is no volatilization of free TDI, so it is very environmentally friendly. Oil-based epoxy resins are also environmentally friendly, but water-based resins are more environmentally friendly than water-based.

2. Construction: The construction method of water and oil is the same, but the water type is relatively speaking, it is better to construct, because the water type is easier to play and more labor-saving, while the oily one is thicker and will be more laborious when playing. Even if the water-based beauty grout accidentally falls on the tile, use a spatula to remove the excess glue, and the rest can be easily wiped off with a wet sponge. Oily ones are more difficult to rub and require the use of alcohol.

3. Color. In terms of color, oily is even better, and oil-based sewing agent has high brightness. The color of the water-based sewing agent is not so high, and it is relatively lighter.

In general, the water-based sewing agent is more excellent, which is the trend of the sewing industry in the future. With the increase of sewing manufacturers, now the sewing industry has become more and more popular, more and more popular, buy sewing agent and give away construction tools, your own construction is very cost-effective. The beauty sewing is one of the few projects in the decoration that can be constructed by itself.

Not only save the decoration cost, make the home beautiful, but also enjoy the fun of DIY, why not?

Enjoy the life brand, my sister's family also chose a water-based sewing agent, after the construction is completed, it is tested with a detector to show that the air is fresh, which can be considered.

1. The surface is smooth as porcelain.

After the tile grout is solidified, the surface is very smooth, and the strength is very good, the wear resistance is good, the self-cleaning is excellent, the cleaning is relatively simple, and it is not easy to appear dirt, which can avoid the breeding of bacteria in the tile gaps, which will bring harm to human health.

2. Waterproof and anti-fouling.

Tile grout has the characteristics of moisture-proof, waterproof and anti-staining, which can make the tile joint not appear dirty and black.

3. The decoration effect is excellent.

Tile grout is made of new polymer materials, high-grade pigments and various chemical additives. It is more effective than white cement and conventional grouts. The color of the sewing agent will also be better, it will look natural and delicate and shiny, and it can be matched with tiles of various colors to bring a good decorative effect.

4. Green and environmental protection, simple construction.

Tile caulk is a green and environmentally friendly product, non-toxic and tasteless, without any harmful substances, and the construction of caulk is very simple and easy to learn.

The advantages of the joint agent can be many, for example, when the beauty of the joint agent is used when it solidifies, it will form a smooth protective film on the surface of the tile, wear-resistant, not dirty, easy to clean, clean when wiped, its hardness, bonding strength, service life and other aspects are much better than the caulk, which solves the problem of black and dirty tile joints, and avoids the breeding of mold in the gaps and endangers human health. The big brands of sewing agents on the market are Nippon, Degao, Zhuogao, Sika, Sankeshu, Polgar, Mapei Building Materials, I have used Porgar's sewing agents, there is no unpleasant smell, it is also very convenient to use, and his anti-mildew, oil-proof and anti-aging effect is really outstanding, I have used other brands of sewing agents before, and in the rainy season, especially in the weather in our south, it is easy to grow mold, ugly and unhygienic. This is not the case with Polgar's sewing agent, and the quality is really nothing to say.

First of all, the beauty sewing agent has a variety of colors to meet people's aesthetic needs, easy to scrub, waterproof and moisture-proof, which can avoid the advantages of mold breeding in the gaps and endangering human health.

Secondly, the best construction time of the sewing agent is generally before entering the furniture, if it is only done on the wall, it can also be done after the masonry is done, and the sewing agent is beautiful; If the floor and the wall are together, it is recommended to do the seams together after the paint is finished, because the ground should be protected, and if the seams are made, it is easy to damage the seams.

Now they all use porcelain sewing agent, it is an upgraded product of beauty sewing agent, you can consider Guangde Mei sewing agent.

Green environmental protection, mildew and antibacterial, rich color, Guangde Mei sewing agent is very good, made of brilliant color, waterproof and wear-resistant, no collapse, anti-oxidation, strong hardness, your first choice.