How do I carpet the whole house? How to lay a carpet?

In the winter, because most people, the bedrooms are tiled. In this way, the whole space will appear to look particularly cold. Therefore, I will choose to lay carpets for the whole house, so that it will look particularly comfortable, warm and warm.

However, if you want to install a whole house carpet, you also need a lot of methods, and you must keep it flat before laying it. Also, be sure to measure the length and width of the floor before laying it. And where the carpet crosses, be sure to keep a 90-degree right angle, etc.

1. How to carpet the whole house?

Generally speaking, the thickness of the carpet is still relatively thick, and if the ground is not particularly flat, then there will be a great wrinkle when it is laid. So be sure to keep the ground clean and level before laying. In this way, when there is a gap, it can also be sewn in time, and choose the starting point of carpeting, first of all, before paving, be sure to use a ruler to measure the length and width of the room.

And accurate to the centimeter, when the shop is raised, it is generally not close to the wall, and at the corner, keep a right angle of 90 degrees. In this way, the visual effect will be better. And, when buying a carpet, there are arrows on each back of the carpet.

Therefore, this also avoids mistakes to a large extent, so when laying, be sure to follow the direction of the arrow. <>

2. Conclusion. Be sure to buy a carpet of the same color, so that when it is not enough, you can buy it in time without too much error. If there are two spliced carpets, then when laying, they must be next to each other, not too loose, but tighter, so as to avoid rework.

When spreading the carpet to the edge of the doorway, it is best to buy a special carpet finish, which will be more complete and not too ugly. Close to the protrusions of the wall or the pillars, it should be cut appropriately to achieve the most exquisite effect. After all, if you do one thing, you either don't do it, or you do it to the best.

At this time, you should choose the right color according to the overall decoration style, choose the right size according to the area of the paving, you should find a professional pavement designer, pay attention to the length and width, pay attention to the splicing, but do a good job of moisture-proof work on the ground, and choose a more decorative and colorful one.

The cut carpet is laid out on the underlayment, then the carpet is rolled up and sewn together at the joints. After stitching, use plastic tape to stick to the seam to protect the seam from being scratched or hooked, then spread the carpet flat, and use a looper needle to make a fluffy stitch at the seam.

You can choose some professionals to help you lay the carpet in the whole house, you should choose some stylish carpets, you should also pay attention to the color of the carpet, you should also pay attention to the thickness, and you should also pay attention to the comfort of the problem.

01 Keep the floor clean.

The first thing you need to do if you want to lay a carpet correctly is to keep the floor clean. Before laying the floor, remove the garbage from the floor, as well as some small wood chips or stones. Only when the floor is cleaned can the carpet be laid.

02 The ground is level.

Be sure to keep the floor level before laying the carpet. If you have already installed wooden flooring in your home. In this case, the carpet can be laid directly.

However, if the home has a cement floor, in this case, you should check whether the cement floor is flat. For uneven places, they should be repaired in time.

03 Fixation of carpets.

After ensuring the leveling of the ground, you can start laying carpets, laying carpets, which can be divided into fixed and unfixed. If it's not fixed, just lay the carpet on the floor and align the four corners of the carpet with the corners of the wall. If it is a fixed carpet.

In this case, the adhesive can be used directly or the floor can be stitched directly with needles and threads.

04 Measure length and width.

When laying the carpet, you should also measure the length and width. The length of the carpet should be slightly longer than the length of the room. In this way, there will be a certain amount of leeway when laying the floor. When determining the width, be sure to remove the width of the thread buckle.

05 Pay attention to the direction of the wool weaving.

After the length and width of the carpet are measured, there is another problem that needs special attention, that is, to pay attention to the direction of wool weaving when laying the carpet. The direction of the wool weaving should be consistent, if you do not pay attention to the direction of the wool weaving, it may lead to the appearance of yin and yang sides of the carpet, and the carpet looks very inconsistent and uncoordinated.

06 Follow the light.

In the process of laying the carpet, it is also important to pay attention to the light when laying the carpet. If the direction of the wool weaving of the carpet is opposite to the direction of the light, after the carpet has been laid, due to the direct exposure of the light. The direction of the wool weaving is just the opposite, and as long as there is sunlight in the following days, the carpet will feel particularly messy.

07 Patchwork carpet.

After the wool orientation of the carpet is determined, the carpet should be spliced directly in this case. When splicing the carpet, you can first fix it from one side. Then use the relevant equipment to tighten the carpet, and then use other methods to sew the carpet.

08 Fixation and cleaning.

After the carpet is spliced, in this case, you can directly use the nails to fix the carpet. After treatment, you can directly use a vacuum cleaner to clean the entire floor, and the carpet can be used normally.

Now, laying carpets is becoming more and more popular in home decoration, but many people don't know the correct way to lay carpets

1. Ground treatment

The carpet is generally laid on the wooden floor or cement floor, and the pockmarks and pits on the ground should be flattened with sandpaper, filled with mud, and then rinsed and dried with clean water.

2. Laying method

Not fixed:Cut and glue the carpet into a whole piece, pave it directly on the ground, do not bond with the ground, and repair it along the corner of the wall. This method is suitable for carpets that are often rolled up or room floors that are infrequent and heavy.

Stationary:The carpet is cut, bonded and stitched together, and fixed around it with the floor of the room. There are two ways to do this:

One way is to use adhesive or double-sided tape to stick the surrounding area of the carpet to the ground; The other is to install a wooden strip with a nail-facing nail on the floor around the room, and fix the back of the carpet on the wooden strip facing the small spike.

3. Two methods of blanket seam

(1) Connect the bottoms of the two carpets with a needle and thread.

(2) Glue together

The glue on the adhesive tape must be heated before it can be melted and pasted. You can first have an iron to melt the glue and put it on. When pasting, the adhesive tape is placed on the seam of the carpet, and one person takes an iron to melt the glue on the paper, and the other person presses the carpet on the freshly melted adhesive tape.

4. Sequence of operations

1) Attach the size carpet of the room. The length of each section of carpet is about 5cm longer than the length of the room, and the width is calculated by the size of the edge buckle of the carpet and the carpet is test-laid.

2) Spread the cut carpet on the ground, fix one side first, then tighten the carpet with a tensioner, and then use the above seam method to stitch.

During the laying process of carpet, attention should be paid to making the wool weaving direction of the carpet consistent with the direction of the main light, so as to reduce the adverse effect of leaving reverse hair marks on the carpet when walking, resulting in messy marks irradiated by the light.

3) After trimming the carpet with a wall knife, you can use a flat spatula to drive the carpet into the nails of the wooden card strip to fix it, and finally seal it with a pressing strip and clean the dust on the carpet with a vacuum cleaner.

5. Precautions:

1) The ground should be cleaned first, leaving no debris such as stones, wood chips, etc.

2) The glue used in the carpet must be laid flat, and the interface should be glued firmly. If double-sided tape is used, it is simple, economical, practical and effective. This kind of double-sided tape, glued on both sides, cover the adhesive layer with plastic film, when using, remove the film and stick it on the sticky object.

3) Pay attention to the junction between the carpet and the corner of the wall edge, etc., and there should be no seams and edge warping.

4) The carpet interface should be coherent and consistent in color, and the seams should be hidden and not revealed.

You can get it for free

Nowadays, many home floors will use carpets, which are both beautiful and practical. Next, PCHOUSE will talk to you about how to lay the carpet.

1. Ground treatment

Carpets are generally laid on wooden floors or cement floors, and in order to ensure the quality of carpet laying, the ground should be treated clean and flat in advance. The pockmarked or uneven places on the ground should be smoothed with sandpaper, then filled with putty, and then rinsed with water.

2. Laying method

Non-fixed: The non-fixed carpet laying is to cut and splice the carpet into the desired shape, spread the whole piece on the ground, and repair the corner of the wall, and do not need to be fixed on the ground. This type of paving is suitable for places where the carpet needs to be rolled up frequently or where heavy objects are not moved.

Fixed: The fixed method of paving is to cut the carpet and splice it into a whole piece, and then fix it around the carpet. There are two ways to fix it:

One is to stick the carpet to the ground with adhesive or double-sided tape; The other is to install wooden strips with nails with nails pointing upwards around the perimeter of the floor of the room, and then fix the carpet to the wooden strips.

3. Carpet seams.

Method 1: Use a needle and thread to connect the edges of the two carpets.

Method 2: Place the adhesive tape at the seam of the carpet, one person takes the iron and dissolves the glue on the paper, and the other person immediately presses the carpet on the adhesive tape of the sol.

4. Sequence of operations

1) Measure the size of the room and cut the carpet. Measure the size of the room with a box ruler and then assemble the carpet according to that size. It is important to note that the length of each section of the carpet should be 5 cm longer than the length of the room, and the width should be removed from the size of the thread buckle that needs to be cut off from the edge of the carpet.

When cutting the blanket, the wool weaving direction of the interface carpet should be consistent to avoid the yin and yang sides.

2) Splice carpets. After cutting the carpet, use one of the above two methods to splice the carpet. When splicing, pay attention to fixing one end of the carpet, and then straighten the carpet with a tensioner and then splic.

3) Fix and clean. The carpet at the corner of the wall should be trimmed to the size of the corner with a wall knife, and then the carpet should be fixed with a flat shovel into the nails of the wooden card strip, and then sealed with a pressing strip, so that the carpet laying is completed. When you're done, remember to vacuum the carpet to clean the dust.

There are two main ways to lay carpets:

1. Movable laying: It refers to the carpet floating on the base layer, and there is no need to fix the carpet with the base layer.

2. Fixed laying: There are two fixing methods for fixed laying, one is the clamp type fixing, and the barbed board is used to pull the carpet; One is the adhesive fixation method, which uses an adhesive to glue the carpet to the floor.

Methods and steps of carpet laying: collapse.

1. Before arguing and paving, it is necessary to measure whether the corners of the wall are regular, and accurately record the angles of each corner.

2. The barbed plate is fixed and laid along the edge of the wall to nail the barbed plate, and the barbed plate is 8 mm away from the baseboard.

3. The seams should be taped on the back of the carpet to paste the two carpets together, and the fluff at the uneven joints should be repaired and the fluff at the joints should be rubbed repeatedly, until the seam traces can not be seen on the surface.

4. Leave the glue for 5 to 10 minutes after scraping the glue during the bonding and laying, and lay it when the glue becomes dry and sticky.

5. After the carpet is laid, use the brace needle carpet to tighten and flatten, and hang it on the barbed board.

6. Cut off the excess carpet edges and clean up the pulled fibers.

7. When cutting the carpet, it should be cut along the warp of the carpet, and for the carpet with a backing, the fluff should be separated from the front, and the warp and weft should be found and cut.