Why can t the aquarium filter be filtered cleanly?

Updated on technology 2024-07-18
28 answers
  1. Anonymous users2024-02-12

    There are several main reasons why the filter cannot be filtered clean: first, the bottom of the tank is paved with stones, and many impurities must be hidden in the cracks of the stones; Rather, there are too many aquatic weeds, which affect the flow of water; Third, the power of the pump is not large enough; Fourth, the filter cotton is already very dirty; If you want to have very clear water, it is recommended that: first, do not pave any stones and sand; 2. Reducing aquatic weeds; 3. Replace one-third of the bottom water every week.

    Fourth, the fish should be raised in moderation, and the feeding should also be able to be eaten.

  2. Anonymous users2024-02-11

    If you want to improve, the best way is to replace this filter a little bigger, and then this water outlet rate is a little more, so that it can be improved well.

  3. Anonymous users2024-02-10

    The best way is to only make a filter barrel, half of this filter barrel has a relatively large power, and the filtration effect is also good.

  4. Anonymous users2024-02-09

    We have a lot of household equipment, these basically have some small problems, the main solution is to deal with it in time, because the filtration function on the aquarium is basically a kind of cleaning ability, not cleaning in place, long-term cleaning can be better filtration function.

  5. Anonymous users2024-02-08

    At this time, it is necessary to replace a filter element in time, and it can also maintain the ventilation effect of this room, and there is also to put less fish.

  6. Anonymous users2024-02-07

    To ** the size of the filter tank, if the filter tank is too small, so the effect is not very clear, you can make a filter tank again, pay attention to the correct use.

  7. Anonymous users2024-02-06

    It feels like it is perfectly possible to install these filters under the water tank and then transport them through the pump and water on top of it, which will filter them cleaner.

  8. Anonymous users2024-02-05

    In fact, you can also find a way to reinstall a filter device, so that you can also make certain improvements, or see if there is a problem to improve.

  9. Anonymous users2024-02-04

    You can add a thick pipe to the place of the drain, put the filter material inside, and punch the water at the bottom, you can have more filter material, the cultivation effect is good, and the water body will be stable.

  10. Anonymous users2024-02-03

    You can change the filter, this filter may not be suitable. After changing it, the filter will work particularly well.

  11. Anonymous users2024-02-02

    You can clean the filter, but if it is still not good after cleaning, you need to consider changing the filter.

  12. Anonymous users2024-02-01

    You can buy a new one and replace it, or clean the filter function, if it really doesn't work, find some professional workers to repair it.

  13. Anonymous users2024-01-31

    First, the drip filter box is directly added to the upper filter, the effect is better, but it is not beautiful;

    Second, add a filter cartridge, suitable for raising small fish, more beautiful than the drip filter box, but the effect is not as good as the drip filter;

    Three: DIY side filter back filter: the back filter on the inside of the cylinder and the back filter on the outside of the cylinder basically need to be customized, you can do it yourself, and you need a certain amount of hands-on ability.

    Fourth, change the bottom filter, if it is a finished cylinder, it is not recommended to perforate the bottom filter, you can buy a non-perforated bottom filter kit to install (you can DIY by yourself); If it is a custom-made fish tank, you can punch a hole to change the bottom filter; The cost of changing the bottom filter is relatively high, but the effect is good, the disadvantage is that the bottom filter tank occupies space, if the fish tank does not have a cabinet or there is no place in the cabinet, it is not easy to change;

  14. Anonymous users2024-01-30

    It is really amazing to raise tropical fish for three years. Can you provide some data?

  15. Anonymous users2024-01-29

    The essence of turbidity is the phenomenon of a large number of spoilage bacteria working in a concentrated manner, and it also shows that your fish tank is more suitable for spoilage bacteria to survive, and not suitable for nitrifying bacteria to survive. This is the reason for this, because a mature biochemical system takes at least a month or more, and if the fish are raised when the system is not fully mature, the water will become mixed if there is a slight carelessness in feeding or changing the water.

    We should try to raise as many aquatic plants as possible, so that the whole aquarium becomes a small ecological paradise, and the water body will naturally become very clear. (5) Put scavengers and moss shrimp in the tank to remove dirt and algae attached to the tank wall. Occasionally, when I am happy, I throw a small fish into it, and I don't get sick while I am free there, eat some small fish and insects, and move it home in winter, and it is also good to raise it for many years.

    The garbage particles in the water are small, and the density of the filtration system cannot reach the corresponding filtration density, so the water will be mixed, second, there are bacteria and microorganisms in the water, and the reproduction rate is accelerated, and the filtration system can not effectively filter and remove, and the muddy water is the fish stocking density is not large? The second is that there is too much food, and the food that cannot be eaten can be mixed with water, and the fish can also be confused with water if they are too full and defecated. The large fish tank is beautiful, but the free fish also makes people feel happy.

    But after moving in, the water in the fish tank was turbid and the fish tank walls were knotted, which bothered us very much. If the fish are raised in the fish tank, the fish have to eat, and the fish are fed with granular materials, and the fish will poop when they eat it, and the poop will be fermented, and over time, the water in the fish tank will become turbid. The second is to put the fish food and eat it within 5 minutes (there is leftover fish food to be cleaned out), and the third is to strengthen the filtration (the power of the submersible pump should match the size of the fish tank, and the filter cotton should be of good quality, compact texture and permeable).

    In this way, the water will be clear after n days.

    The possibility of ciliate discharge is greater, potassium permanganate solution is mixed, in the tank, pay attention to oxygen, generally the water body is red. After about five minutes, add a few vitamin C tablets to restore the water, and wash the filter cloth. Ornamental fish are fed once a day, or once every two days, and the fish food should not be too much each time, and it is advisable to eat it in about five minutes.

  16. Anonymous users2024-01-28

    You can clean the aquarium thoroughly, it may be that there is a problem with some of its systems, so the water cannot be cleaned, or you can replace an aquarium and so on.

  17. Anonymous users2024-01-27

    You can change the water properly, and it is normal for the water to be dirty in it, after all, there will still be some excrement in some of the things raised inside.

  18. Anonymous users2024-01-26

    It is necessary to have a very good feeding density. Also, the number and amount of feeding should be reduced. And it is necessary to change the water in time to control the density of the fish. This will solve the problem. And it doesn't make the water particularly dirty.

  19. Anonymous users2024-01-25

    Clean the bottom filter. Because it may be that the bottom filter is too dirty, the water is very dirty, so the bottom filter should be cleaned.

  20. Anonymous users2024-01-24

    1. The first step is to fill the water (in the same tank).

    You must know that the siphon principle can be formed, there is no need to drill holes, and when the water is filled first, no air can be left in this set of pipes. So we have to plug the gas outlet and add water to the bottom of the whole pipe. After filling up the water, unplug the outlet plug and close the drain valve at the same time, and remove the water pipe that fills the water.

    2. Open the valve to start siphoning.

    Open this draining valve, the whole pipe will start to siphon under the action of atmospheric pressure, and the water in the fish tank will flow down this pipe to the bottom filter tank. You can see the transverse water level pipe of the whole pipe, the water in it is full, the normal bottom filtration cycle of the fish tank starts to work, and we can turn on the water pump at the same time.

    3. After a power outage.

    After a power outage, the water level of the fish tank will slowly lower than the water level of the horizontal water level pipe, and there will be water storage in the U-shaped pipe on the left side of the horizontal water level pipe, which is to start the siphon again when the power is called.

    4. After the call.

    When the call comes, the bottom filter pump begins to work normally, the water level of the fish tank will continue to rise, as long as the water level is higher than the transverse water level tube, the water in the U-shaped tube will be pushed to the transverse water level tube under the action of atmospheric pressure, when the water flow in the water level tube is full, the siphon principle will start again, and our entire lower filter cycle will operate normally.

  21. Anonymous users2024-01-23

    DIY filter by yourself, the easiest is to make the bottom filter, simple, but it works very well. Many people abroad will use a bottom filter. Send you a finished product**. It's easy to do.

    Explanation: The role of the filter cotton, filtering the fish feces and leftover feed.

    Biochemical balls: Cultivating nitrifying bacteria and acting as bio-purification.

    Activated carbon: adsorbs odors and harmful elements and clarifies water quality.

    Coral stone, ceramic ring: culture nitrifying bacteria, biological purification.

    The principle of all filters is the same, except for the appearance and the selection and placement of filter materials.

    The filter must have 2 or more filtration methods, namely: physical filtration, biochemical filtration, and chemical filtration.

    Physical filtration: It is the use of mechanical methods to isolate the larger particles in the water. For example, the remaining feed particles, the bones of dead fish, the excrement of the fish body, secretions, vomit, mucus on the body surface, etc., generally use sponges, spray cotton wool, fine mesh nylon nets, palm leaf fibers, etc.

    It is usually installed at the beginning of the filtration system for easy cleaning.

    Biological filtration: Cultivating beneficial bacteria and decomposing harmful elements such as ammonia, nitrite, nitrate, phosphate, etc. Commonly used filter materials are: biochemical balls, ceramic rings, glass rings, coral sand, etc. (the most important filtration method, maintaining the ecosystem).

    Chemical filtration: It is a method of using chemical agents to remove impurities in water, and the preparations used include water quality stabilizers, flocculants, algaecides, protein decomposition agents, deodorants, etc.

    Adsorption filtration: It is a very high carbon content substance such as wood, coal, fruit shell, animal bone, etc., which can adsorb proteins, trace elements, decolorization, deodorization, and even ozone molecules can be absorbed by it. It can also absorb fish urine, microalgae in the water, and drugs.

  22. Anonymous users2024-01-22

    Here's how to use the filter on the aquarium:

    3. Turn on the power supply, observe the operation, if the water supply and water supply are normal, you can use it.

    4. Clean and replace the filter material in a timely manner, and artificially add nitrifying bacteria, which will be better.

  23. Anonymous users2024-01-21

    Answer: There are many kinds of fish tank filters, the bottom filter should be placed at the bottom of the fish tank, the upper filter should be placed on the top, and the filter cartridge needs to be piped into the fish tank. Filter media should be added to the filter box, so that the water can be purified after passing through the layers of filter media. Filtration equipment must be turned on at all times to keep the water flowing, which is helpful for maintaining water quality and also for the health of the fish.

    Because I don't know what kind of fish tank filter you have, can you try this method first?

  24. Anonymous users2024-01-20

    First you have to distinguish what kind of filter you are:

    Generally speaking, there are two ways to filter the finished aquarium.

    1. Upper consideration: that is, there is a filter box on the top of the fish tank, and the water is pumped into the box through a water pump and filtered and then naturally flows into the fish tank.

    2. Bottom box: The water enters the bottom box by gravity, and after filtration, it is pumped back into the cylinder by the water pump.

  25. Anonymous users2024-01-19

    Which aquarium, what kind of filter, generally after you buy, isn't it all the sales staff who come to install and debug it?

  26. Anonymous users2024-01-18

    Why is your fish tank water not filtered cleanly? First of all, understand the structure of the fish tank, which is a must-see for novice fish farming.

  27. Anonymous users2024-01-17

    1. Physical filtration, the filter material is filter cotton (coarseness).

    2. Chemical filtration, the filter material is ammonia absorption, soft water resin, grass mud pills, and activated carbon.

    3. Biological filtration, the filter material is glass ring, biochemical ball, biochemical cotton, etc.

  28. Anonymous users2024-01-16

    If the filter of the aquarium fish tank is not properly placed, the water in the fish tank will still be turbid, so how to install the filter is very important. Here are the two filter placement methods summarized for you, let's take a look.

    First, the basic method.

    1. The pump is properly installed --- form a cycle, and leaving no feces is the best test.

    2. The wattage of the pump is a little larger than the conventional one--- the water absorption is large, and the circulation is accelerated, 3. The filter cotton is thicker--- which not only plays the role of filtration but also serves as a nitrifying bacterial bed to achieve biological circulation. I've seen a lot of pumps in fish tanks with high suction ports, so don't laugh at this method. In addition, I have encountered white fog in the new tank, and I have tried to change the water and add medicine, so it is better to adjust the pump and add a little water purification king, and there will be no more such things.

    However, with the addition of water purification king, you must look at the filter material, and wash it in time if the water overflows.

    Second, the cylinder aesthetic method.

    In addition, many fish are raised with submersible pumps (filters). After buying, the outlet hose and its set of outlets should be connected to the water surface from the outlet located at the bottom of the tank, and then filtered through the filtration and flowed into the water to complete the water circulation. This hose is ugly in the water and dirty and hard to wash due to its softness and threads.

    I have a solution: take the electrician's plastic sheathed wire pipe (hard, straight) (available in building materials stores) according to the distance between the pump and the water surface, and connect the water with a sheath wire elbow at a right angle. In this way, the pipe occupies less space in the water, is welt, beautiful, and easy to scrub.

    Give it a try. If there is a surf port, two outlets can be connected to the filter with one in a tee.

Related questions
8 answers2024-07-18

Where there is sewage, you need it, and we have summarized the most complete filter application range information from the Internet, hoping to help you: >>>More

14 answers2024-07-18

In fact, there is no fixed requirement for the time frequency of cleaning, about once a week to observe, if the filter cotton turns yellow, and the water quality is very poor, a little turbid, you can take out the filter cotton to clean it. >>>More

13 answers2024-07-18

Full range of compressed air filters: Accuracy class:

c:3μt:1μa: >>>More

4 answers2024-07-18

Filter base plate modification.

The bottom of the original filter is about 10cmm from the ground of the steel mesh structure, the dust falling from the filter is all in the lower part of the steel mesh, because the height is too low, it is very inconvenient to clean and clean, in order to improve this situation, galvanized iron sheet is installed at the bottom of the original steel mesh to increase the strength of the bottom, which is convenient for replacing the filter element and maintenance, and convenient for cleaning. >>>More

5 answers2024-07-18

Because iron products are prone to rust, it affects both aesthetics and health. Therefore, many of our daily necessities are made of stainless steel. Stainless steel filters are more practical than plastics and other materials in terms of longevity and health. >>>More