How can I keep the fish tank water well?

1. First choose a larger fish tank, put an oxygen pump in the fish tank, and turn on the fluorescent light. When keeping water in the tank, it is best to put some stones and fish grass that the fish like. Then the tap water was dried for three days.

It is better to fill the air with an air pump and disperse the chlorine gas before use. Whether it's new or old, water needs to be disinfected. The new one is one step more than the old one.

That is, after the cylinder is glued, it will be placed for 7 days to remove the smell of glass and rubber in the cylinder, and the old cylinder can directly produce water.

After 2 hours, soak, clean the water in the tank, wash the whole with clean water, wash, repeat the filter medium, and rinse the potassium permanganate completely. The sink mainly uses the water in the sink to absorb the smell of glass rubber and the smell of the new sink, and can also be used to test if it is completely soaked for 24 hours. Generally, fill the sink with water and soak it for 24 hours.

3. After a day of aeration, the water can be heated and filtered, and the water temperature should be adjusted to the best temperature for fish farming, and it will not work in the future, and the specific problem and the wattage of the heating rod depend on the size of the tank and the needs of the fish. The temperature of the water rises, and the water in the tank is cloudy, so nitrifying bacteria can be added. Without interrupting the oxygen pump, enough oxygen is administered to nitrifying bacteria to improve the survival rate.

Trapped water: The first step in raising water is to trap the water, and the purpose of trapping water is to remove the residual chlorine in the water, so as not to affect the health of the fish. Filtering:

In order to reduce the impurities in the water, it is also necessary to keep the water filtered when raising it. After the trapped water is poured into the fish tank, it is usually filtered several times until the water becomes clear. Culture:

The most important thing in water cultivation is to cultivate bacteria. The purpose of culture is to establish a nitrification system that converts ammonia nitrogen from water.

1. How to raise the water in the fish tank.

1. Trapped water: The first step in raising water is to trap water. Because the tap water is usually used to raise fish at home, although this water is not polluted, there will still be residual chlorine after disinfection, which will pose a certain threat to the health of the fish, so it needs to be removed.

Chlorine removal is usually done by drying, but if the time is short, aeration can also be considered.

2. Filtration: In order to reduce the impurities in the water, it is necessary to keep the filtration when raising the water. After the trapped water is poured into the fish tank, it is usually filtered several times until the water becomes clear.

After that, the filter should be turned on all the time so that the water quality can be maintained, and the flowing water will also help to increase the dissolved oxygen.

3. Cultivating bacteria: The most important thing in water cultivation is cultivation. The purpose of culture is to establish a nitrification system, where the decomposition of organic matter in the water produces ammonia nitrogen, which is a harmful substance to fish, and by nitrifying bacteria, it can be transformed into a non-harmful substance to fish.

Second, you can release fish after raising water for a few days.

Fish are usually kept in water for five to seven days before they can be released. Fish farming first raises water, the quality of the water and the health of the fish is also closely related, if the water quality is relatively poor, the fish will also be easy to get sick, and the state will become bad. Normally, the water needs to be trapped for a few days to remove the chlorine inside.

Filtration and oxygenation are then required, which removes impurities from the water and also boosts dissolved oxygen, which is great for the fish's respiration.

1.First, choose a larger fish tank, add an oxygen pump to the fish tank, and turn on the fluorescent lamp.

2.When using a fish tank to raise water, it is best to put pebbles and fish grass in the fish tank in advance.

3.The tap water is then exposed to sunlight for three days. It is best to inflate with an air pump before use to expel the chlorine gas.

What are the requirements of fish for water.

1. Water temperature: Fish farming should first pay attention to the water temperature, too low temperature will lead to a decrease in the appetite of the fish, and for some tropical fish, low temperature will even make them die. Usually the water temperature should be controlled above 20 so that the fish will be more active.

You can use a heating rod to raise the temperature, but it must not rise too quickly.

2. Water quality: If the water quality is not good, the health of the fish will also be affected. In order to maintain water quality, it is necessary to change the water regularly, and if the water is not changed for a long time, harmful substances in the water will increase, which can lead to fish poisoning.

Usually, the water change cycle is one week, and if there is a filtration equipment, it can be changed once every half a month.

3. Dissolved oxygen: The dissolved oxygen of the water body will affect the breathing of the fish, and if the oxygen is low, the fish will float their heads, and a large number of people will die if they are not oxygenated in time. In response to this situation, you can use an oxygen pump to inject oxygen into the water, and the time of oxygen injection is about 2-4 hours a day.

If it is a new fish tank, the first thing to do is to disinfect it. Here's how:

1. Let the fish tank stand for a few days, then disinfect it with potassium permanganate solution, then soak it in water for 1-2 days, and then pour out the water.

2. Fill the fish tank with water, turn on the filtration system and oxygen supply system, and adjust the temperature.

3. Add nitrifying bacteria to the water to cultivate the nitrification system.

4. Finally, let the fish break into the tank. After a week, if the fish in the tank is normal, you can officially release the fish.

1. First choose a larger fish tank, add an oxygen pump to the fish tank and turn on the fluorescent lamp.

2. When using the fish tank to raise water, it is best to put pebbles and fish grass that fish like to eat in the fish tank in advance.

3. Then put the tap water in the sun for three days. It is best to inflate with an air pump and dissipate the chlorine gas before use.

1. Reduce the feeding density 2, reduce the amount of bait 3, reduce the sudden change in water quality and speed up the removal of turbidity: 1. Change the water (pay attention to the previous article 3) 2. Increase the efficiency of the filtration system 3. Chemical precipitation treatment (treat the surface but not the root cause) 4. Purification treatment of plants and microorganisms.

The method of raising fish tank water is to raise fish first, prepare pure water, do a good job of filtration system, place aeration pumps, warming rods and other equipment, and establish nitrifying bacteria in the fish tank, about a month later, put in a fish tank, if there is no problem, you can start raising fish.

1.First, soak the cylinder with potassium permanganate for disinfection, or brush it clean and expose to the sun.

2.Expose the water to the sun for a few days, pour it into the fish tank, open the pump, and in the case of tropical fish, heat the water to a certain temperature.

3.Before pouring the fish into the tank, put it in the tank with the bag, and after an hour, pour the fish into the water.

The fish tank is a small ecosystem, and it makes sense that fish are raised before water. The pH and dissolved oxygen in the water should be monitored in a timely manner, and nitrifying bacteria should be cultivated to improve the water quality. In short, care and patience can raise good water.

If you want to raise the water in the fish tank, first of all, you have to put some green plants on the bottom of the fish tank to lay a layer of fine sand, as well as a coarse pebble, and then when the water pump heater is fully equipped and the head is fed, it must be fed a little less, so that her water will last longer and is not easy to break.

First of all, the fish tank should be disinfected and sterilized to prevent the bacteria in the tank from integrating into the water. You can use potassium permanganate solution to soak the fish tank for 1 2 hours, and clean the filter system, decorations, etc. in the fish tank.

It is best not to use unclean water for the water in the fish tank, it is better to use clear tap water, and not to put too many weeds in one tank will cause the water in the fish tank to become turbid, which will cause the fish to get sick, lead to a lack of oxygen, etc.

Put some stones appropriately, and don't change the water too often. The number of fish must be considered according to the fish tank. Also, change the water, don't finish changing the original water.

Fish farming first raise water, prepare pure water, do a good job of filtration system, place aeration pumps, warming rods and other equipment, and establish nitrifying bacteria in the fish tank, about a month later, put in a fish that breaks into the tank, if there is no problem, you can start fish farming.

Don't bring oxygen to the pump, plug the air outlet, and the garbage will be pumped into the sink, or it will not be broken, and a small part will be washed back into the tank, and the water nitrifying bacteria will not be added casually, added to the filter cotton, or on the glass ring.

The first is the feeding density and the amount of feeding, assuming that our ornamental fish do not have any diseases, then these two elements are the fundamental conditions for us to maintain the water quality of the fish tank.

The first step in raising water is to trap the water, and the purpose of trapping the water is to remove the residual chlorine in the water so as not to affect the health of the fish.

In order to reduce the impurities in the water, it is also necessary to keep the water filtered when raising it.

The most important thing in water cultivation is to cultivate bacteria.

If you want the water quality in the fish tank to be good, you must pay attention to the excessive density of fish breeding, especially the fish tank with poor filtration, or the more fish, the more difficult the water quality in the fish tank to raise.

You have to maintain a good habit of changing the water frequently every day, and you should also regularly drain the water and put a little seaweed and other plants in the fish tank.

Fish tank water maintenance must require a pair of hard-working hands.

Try to change the water regularly and dry it in advance so that the fish will not be in a state that is not suitable for them.

Whoever puts it in the fish tank must filter it, so that it will become clear.

How can I keep the water in the fish tank well? You can add a small amount of salt to the fish tank to sterilize. And the water is changed frequently.

Do a good job of filtration system, install aeration pumps, warming rods and other equipment, and establish nitrifying bacteria in the fish tank.

Summary. Hello, I'm a good answer.

Fish farming starts with water.

Tap water should not be used directly, at least for more than three days after contact, or treated with chlorine removal drugs, otherwise residual chlorine and other harmful substances will cause harm to the fish and cause them to die quickly.

How to raise water in a fish tank?

Hello, I'm a good answer. Fish farming starts with water. Tap water should not be used directly, at least for more than three days after contact, or treated with chlorine removal drugs, otherwise residual chlorine and other harmful substances will cause harm to the fish and cause them to die quickly.

It is recommended to use a suction pipe to change the water, and if there is no filtration system, it will be changed to 1 5 in 2 3 days, and if there is a filtration equipment, the water change will not exceed 1 3 in a week.

Keep oxygen adequate. When the container is too small and there are too many ornamental fish, it is easy to have the symptoms of the fish mouth up to drink water, if you find that there is a lack of oxygen, please supply oxygen in time, water and oxygen are equally important, please prepare an oxygen pump.

How do you grow digestive bacteria with water?

Artificial nitrifying bacteria can be added, that is, artificial nitrifying bacteria such as liquid, powdered, and dry spore sold on the market. Liquid nitrifying bacteria only require a vial cap.

Common steps to open the tank and raise water:

1. After the new tank is done, ventilate for 1-2 days to dissipate the smell. After that, it's time to open the cylinder.

2. Brush the jar with large salt water. After pumping the water clean, add new water, set the filter device in place, and turn it on.

3. Add potassium permanganate for comprehensive disinfection until the water turns dark purple. Soak for more than 24 hours, filter for 1 hour, do not use boiling water.

The basic principle of water cultivation is to build hail and create a good microbial system to separate the main harmful substances (fish feces and food scraps, which are organic matter) into harmless substances; This is the core idea, no matter what kind of tank, what method is used to open the tank, the role of the microbial system cannot be ruled out. Here we place more emphasis on improving the capabilities of the microbial system.

Fish farming first raises water, first of all, do a good job of trapping water, you can put tap water in the sun. Secondly, it is necessary to establish a good nitrification system. Nitrifying bacteria can be cultured by pouring them into water.

Nitrifying bacteria are conducive to the formation of a good microecological balance. When raising water in the fish tank, first of all, we must do a good job of trapping the water, you can put the tap water in the sun for two or three days, and after the new aquarium is disinfected, it is generally directly added to the fish tank for use, because the tap water contains a lot of chlorine, and it should generally be soaked in water for 2-3 days.

After being trapped in the water, the nitrification system in the water can be cultivated, and the nitrifying bacteria can be poured into the water for cultivation, and various filter media can be placed for it to adhere to, and the amount of dissolved oxygen in the water can be kept sufficient. Usually a nitrifying environment can be cultivated in a month or two, and a small amount of water change can be carried out in this process, which can help to cultivate a nitrifying environment more quickly.

In addition to nitrifying bacteria, there are some other beneficial bacteria that are recommended for use. Beneficial bacteria can not only efficiently clean up organic matter in water, but also help to form a good microecological balance.

1. The new fish tank needs to be disinfected first. Let the fish tank sit for a few days, then disinfect it with potassium permanganate solution, then soak it in water for 1-2 days and then pour it out.

2. After that, you can fill the fish tank with water, and turn on the filtration system and oxygen supply system to adjust the temperature. Nitrifying bacteria are then added to the water to create a nitrification system.

3. Finally, put some fish into the tank. After waiting for a week, if the fish in the tank is normal, you can officially release the fish.

The recommended approach is as follows:

New tank disinfection: clean the new tank, disinfect it with salt, and wash it 1-2 times. Fill the main cylinder with water, put the water quality in the main cylinder to stabilize it, and use an air pump to pump air in the main cylinder.

The filter material is placed properly in the bottom cylinder, but it is recommended that the filter material should not be overfilled in the early opening of the cylinder, and the normal filter material should be filled with one-half on the line, and the culture of nitrifying bacteria in the early stage is effective from white cotton, biochemical cotton, rattan cotton, and black cotton. Therefore, cotton can be put more, and the rest of the bacterial house, biological ring, ceramic ring, infrared, quartz ball, etc., can be put in a small amount, and can be gradually added in the later stage.

At this time, there is no need to turn on the main water tank to run your fish tank. A separate small water pump is used in the bottom cylinder, and the filter cylinder is 120cm-150cm, and a 1000L-2000L water pump can be selected. You can choose 3000L for more than 150cm, but it is recommended that the pump should not be too large.

A separate small water pump is placed into the last stage of the bottom tank, and the water pumped out is placed in the first stage physical area after being connected with a hose, so that the structure of the bottom tank independent culture and digestion system is formed. On the first day, only one-third of the water in the bottom tank is put into the water body to stabilize the water, and the water pump and heating rod are turned on.

After the filter cylinder runs for 3-5 days, the main cylinder water pump is turned on and the separate small water pump stops running. Put the fish into the tank, observe the water quality, and the body surface of the fish. If the fish in the tank is fine, it is no problem to put in the fish to be molded and raised in a group after 2-3 days.