What is the reason why the integrated stove does not catch fire?

Updated on Car 2024-07-25
15 answers
  1. Anonymous users2024-02-13

    This is the most common problem, but also people are generally more concerned about the problem, found that the ignition is not on fire and there is no sound of clicking, it is necessary to check whether the battery is charged. The integrated stove has an electronic induction firewall, which can automatically cut off the gas source in the case of high temperature and open flame, and automatically cut off the gas source when the fire goes out accidentally, and automatically cut off the power supply in case of leakage, which is very safe to use. The lower exhaust design eliminates the noise source placed on the human head, and applies ultra-low, noise technology and silent air duct design technology to reduce noise.

    Modern intelligence, high security. At present, many brands of integrated stoves have intelligent control, leakage and gas leakage detection, and automatically cut off the gas source and power supply to ensure the safety of users. Before each use of the integrated stove, it is necessary to check whether the fire cover is placed, whether the switch is closed, and the gas valve must be turned off after use; Be sure to inspect the gas line regularly every once in a while and secure it with a pipe hoop.

    Kitchen fumes are even more harmful than smoking, with more floating and sinking particles, and harmful substances are more likely to enter the human lungs. Therefore, health-conscious people should also use integrated stoves. The integrated stove is based on the principle of deep well downward discharge or side suction lower discharge, and then the lower discharge produces a fluid negative pressure area, so that the oil smoke can be sucked down like magic, and the phenomenon of oil smoke rising can no longer be seen, and its oil smoke absorption power is as high as 95% or more.

    In addition to satisfying the basic demands of oil smoke, consumers should be concerned about cleaning. Our daily cleaning is generally the cleaning of cooktop countertops, range hood surfaces, oil nets and oil boxes. My aunt is not short, and she used to accidentally hit her head when she used to use a wall-mounted range hood.

    The emergence of Senge integrated stove effectively solves this problem. The smoking port of the T1Z is close to the pot, which not only solves the problem of oil smoke from the root, but also avoids the problem of bumping. The resulting signal is safely transmitted into the pulse (from thermocouple solenoid valves to thermocouple solenoid valves).

    As long as these two standards are grasped, many flameout problems can be solved.

  2. Anonymous users2024-02-12

    There are three reasons for this situation, the first is that the battery installed in the integrated stove has no electricity, mainly because there is no gas or anything like that, and the third time, because there is some water on these tops, so it will not be able to hit.

  3. Anonymous users2024-02-11

    The reason why it can't catch fire is because there is no gas, or the battery is dead, the circuit is in poor contact, or the overvoltage protection and the pipe is blocked, which will cause the fire to not ignite.

  4. Anonymous users2024-02-10

    If you can't get the fire, this may be the reason, because it's already very wet, and it may not catch fire after it's wet, so we have to keep it dry.

  5. Anonymous users2024-02-09

    It could be because your gas pipes are clogged, and it could also be because you don't have gas in your house, so it won't catch fire.

  6. Anonymous users2024-02-08

    Integrated stoves are a must-have item in modern kitchens, making cooking easier and more convenient. But when using an integrated stove, there are also some problems, one of which is that it cannot be fired. So, what are the reasons why the integrated stove can't catch fire?

    1.Gas Pipeline Problems: One of the main reasons why integrated stoves fail to ignite is gas pipeline problems.

    If the gas pipeline is not tightly connected or the gas pipeline is blocked, the gas will not be able to pass through and the ignition will not be possible. At this point, it is necessary to inspect the gas line, remove the blockage or adjust the joint.

    2.Spark plug problem: The integrated stove does not catch fire and may also be a spark plug problem. The spark plug is an important part of igniting the gas, and if the spark plug is damaged or bent, it will not ignite. At this point, a new spark plug needs to be replaced.

    3.Fire switch problem: The integrated stove may also fail to ignite due to fire switch problems. If the fire switch is damaged or in poor contact, it will not be able to ignite. At this point, it is necessary to repair or replace the fire switch with a new one.

    4.Gas pressure problem: The integrated stove cannot catch fire, or it may be because the gas pressure is too low. If the gas pressure is insufficient, the gas cannot be ignited. At this point, the gas pressure needs to be adjusted.

    5.Thermistor problem: The integrated stove cannot catch fire, and it may also be because of the thermal flame resistor problem.

    The thermistor is the element that controls the gas switch, and if the resistor is damaged or aged, it will affect the false sound of the gas, resulting in the failure to ignite. At this point, the thermistor needs to be replaced.

    In short, if the integrated stove cannot be fired, you need to check the above problems first and eliminate the fault before you can use it. If you don't know how to repair, it is recommended to find a professional person to inspect and repair.

  7. Anonymous users2024-02-07

    The integrated stove is an important kitchen product, and the integrated stove will fail during use, such as the situation that it can't catch fire, and many people don't know the reason when they encounter this problem, so what is the reason why the integrated stove can't catch fire?

    1. Whether there is gas: When you encounter a gas stove that can't hit the Fuhu Chan fire, you must first check whether there is still gas, and if you don't have it, you have to add gas.

    2. Poor circuit contact: the main thing is to check whether all the connecting wires of the pulse are connected correctly, and if there is a mistake, the line is connected accurately.

    3. Gas path blockage: Once the gas path is blocked, it is necessary to dredge the gas path.

    4. Micro switch damage: micro switch is a very small place in the stove, but it is more difficult to repair than the usual fault, generally speaking, it is not recommended that the owner repair it himself, this is a fine, professional work, it is best to ask a specialist to solve.

    5. Dirty ignition needle: The kitchen is easy to be dirty, especially easy to be contaminated with oil, etc., the stove is placed for too long, and the ignition needle may be covered by stolen goods, so you need to clean the dirt of the ignition needle, and then try to ignite.

    6. Improper position of the ignition needle: if you want to ignite the fire due to lack of dust, the gas stove has certain requirements for the distance between the ignition needle and the fire cover, once the deviation distance is too much, it will cause the gas stove to not catch fire, generally speaking, the distance between the ignition needle and the fire cover is 4mm, and it should be aimed at the fire hole.

    The above is the introduction of what is the reason why the integrated stove does not catch fire, if you encounter the situation that the integrated stove does not catch fire, it is recommended to find out the cause first, and then solve the problem.

  8. Anonymous users2024-02-06

    The integrated stove is particularly simple to use, with integrated range hoods, gas hobs, storage cabinets and sterilizers. As long as you've used these kitchen utensils, you'll generally be able to use them。The principle of use is similar.

    If you can't, you can follow the instructions. When using, pay attention to snap the bayonet of the copper furnace lid into the positioning pin of the aluminum furnace cover to keep the small hole on the side of the aluminum furnace cover unobstructed. When the ignition is off, we are usually unable to ignite continuously.

    We need to stop for a few seconds before **. Also, be sure to take care to clean the machine. Airless.

    The average person has a good idea about this, but some people may be sloppy or busy at work and often forget, so when you come across a stove that can't make a fire, the first thing to check is if there is still gas. Solution: If the bottled gas is out of gas, add gas; If it's piped gas, make sure the gas valve switch is on.

    Poor circuit contact. This is an easily overlooked problem, but one that many old users often encounter. The main thing is to check whether the positive and negative poles of the battery box are rusty and whether the wiring is bad.

    Solution: If the furnace has poor electrical connections, remove the rust and connect the wiring accurately. Overvoltage protection.

    Many cooktops have overvoltage protection, which will not be activated once overvoltage. Solution: If the rice cooker is overpressure protected, try a pressure reducing valve at this time.

    Clogged pipes. This is a very common question. Once the pipe is clogged, check the outlet valve

    Generally speaking, if you smell gas but your cooker won't ignite, it's most likely a gas blockage. Solution: If the furnace tube is clogged, the tube must be unblocked or replaced.

    The micro switch is damaged. There is a small place in the furnace at this time, but it is more difficult to repair than usual. In general, it is not recommended for car owners to repair it themselves.

    Solution: The micro switch of the cooker is damaged. It's a delicate and professional job.

    It's best to ask a professional to solve it. The ignition needle is dirty. The kitchen is a place that can easily get dirty, especially if it is easily contaminated by oil stains and so on.

    If the stove is left for too long, the ignition needle can easily become stained with oil. Solution: At this time, you need to clean the grease on the ignition needle, and then try to ignite.

    Improper placement of the ignition needle. Improper placement of the ignition needle on the stove. If you want to start a fire, the stove has certain requirements for the distance between the ignition needle and the fire cover

    Once the distance is too far, the stove will not ignite. Solution: Generally speaking, the distance between the ignition needle and the fire cover is 4-6mm, which should be aligned with the fire hole.

    The high-voltage line of the stove is aging. The furnace has high-voltage wires and their connectors. Once the high-voltage line is aged, it is easy to cause the stove not to catch fire.

    Solution: At this time, only one set of high-voltage protection is required. This should be paid more attention to in daily life.

  9. Anonymous users2024-02-05

    Because there is no gas in the integrated stove, there is no fire without gas, and you need to pay a fee in this case.

  10. Anonymous users2024-02-04

    The main reason is likely to be that the battery in the integrated stove is out of power, so there will be no fire, which is also very normal, and it is enough to replace a battery.

  11. Anonymous users2024-02-03

    Because there is no battery, because there is no gas, etc., the integrated stove needs to be ignited by batteries, and it will not catch fire if there is no gas.

  12. Anonymous users2024-02-02

    It is because the gas stove valve is out of power, so it can't catch fire, you can replace the battery, or check if there is gas.

  13. Anonymous users2024-02-01

    The reason why the integrated stove can't catch fire:

    There is no gas. This point is often easy to forget in life, and we may forget to charge the gas bill after using it, and the next time we use the integrated stove, we will not be able to catch fire. So what about this case, here's how we do it:

    If it is bottled gas, add gas; If it's piped gas, remember to pay the gas bill in time.

    The battery is dead. If there is no sound when ignition, then we need to check whether the battery is still charged. How to do it: If the battery is dead, we have to replace the battery, which depends on what kind of electromagnetic your stove needs.

    Poor circuit contact. In this case, we need to check whether the two parts of the positive and negative poles of the battery box are rusty, if there is rust, there will be poor line contact. Specific method: remove the rust and ensure the accurate connection of the line.

    Overvoltage protection. Some stoves have the function of overvoltage protection, and they will automatically trip if they are overvoltaged. So, how to do it: change a pressure reducing valve.

    The switch is damaged. The switch controls the ignition and ** of the gas stove, and it needs to be twisted every time the stove is turned on and off, and it is likely to be damaged after long-term use. In this case, it is not recommended that we deal with it ourselves, and it is best to ask a professional person to solve this problem.

  14. Anonymous users2024-01-31

    1. Pipeline blockage.

    Check the gas outlet valve first, if you smell the smell of gas and the stove cannot be lit, it is likely that the gas is blocked. Solution: Ask a professional to dredge the pipes of the integrated stove or replace the pipes.

    2. Poor circuit contact.

    This situation is often encountered among old users, first check whether the positive and negative poles of the battery box are aging and rusty, and whether the line is in poor contact. Solution: Remove the rust and reconnect the line.

    3. The battery is dead.

    If the integrated cooktop does not catch fire and does not make a clicking sound, the battery may be dead. Solution: You need to replace the No. 1 battery.

    4. Overvoltage protection.

    The integrated stove has overvoltage protection function, if the overvoltage will cause the integrated stove to not catch fire. Solution: Replace the pressure reducing valve and try it.

    What to pay attention to when using an integrated stove.

    1. Before use, see if the fire cover is put in place, the knob bend is missing whether the switch shows the closed state, and the air source valve must be closed after each use of the integrated stove.

    2. If you are using a pulse ignition gas stove, you can replace the battery when there is an intermittent ignition to continue to ensure the normal operation of the gas stove.

    3. When using the flame-out protection to bury the stove, press vertically at the maximum fire for 3-5 seconds after igniting the fire.

    4. When installing the built-in cooker, leave more than 20cm of space under the cabinet, and leave ventilation holes.

    5. If it is found that there is yellow flame, backfire or other abnormal flame burning, adjust the damper according to the instructions on the manual.

    6. In order to make the integrated stove work better, daily cleaning is essential, and the fire cover and ignition magnetic needle should be cleaned in time. In case of overflowing, clean up the fire lid immediately.

    7. Flammable and explosive materials must be kept away from the stove.

    8. The use of stoves with integrated stoves is particular, please do not use pots and pans that are too large and too flat.

    9. The gas connection hose of the integrated stove should be checked regularly, and the hose should be fixed with a pipe hoop. In general, it is recommended that the gas hose be replaced once a year.

    10. After cooking, close the main valve first and then close the knob.

  15. Anonymous users2024-01-30

    Hello dear, what is going on with the integrated stove suddenly not catching fire: 1. No gas Usually people will have a bottom in their minds about this situation, but some people may be more sloppy, or busy with work, and often forget, so when the stove does not catch fire, the first thing to check is whether there is still gas. Workaround:

    When the bottled gas is out of gas, it needs to be refilled. In the case of piped gas, make sure the gas valve switch is open. 2. The battery is not charged This is a problem that is usually easy to encounter, and if you find that the ignition is not on fire and there is no clattering sound, you must check whether the battery is charged.

    Solution: If the cooktop battery is not available or runs out, you only need to replace the battery. 3. Poor circuit contact This is a problem that is easy to ignore, but it is also very common.

    Solution: The main thing is to check whether the positive and negative poles of the battery box are rusty, and whether the line has poor contact. If the circuit of the stove is not in good contact, the rust needs to be removed and the wiring should be connected accurately.

    4. Overvoltage protection Many stoves have overvoltage protection function, and once overvoltage, it will not start. Solution: If the stove is overpressure protected, then you need to change a pressure reducing valve to try.

    5. Pipeline blockage This is a very common problem, once the pipeline is blocked, it is necessary to check the bridge outlet valve which is rotten, generally speaking, it is likely to be gas blockage if the gas smell can be smelled and the stove is not on fire. Solution: The stove pipe is blocked, then the pipe should be unblocked or replaced.

    Hope it helps.

Related questions
14 answers2024-07-25

The reasons why the natural gas stove does not catch fire are as follows:1. When the gas stove battery is out of power and cannot catch fire, you can check whether the battery has electricity, if there is no electricity, not only can it not ignite but also the solenoid valve will not open. >>>More

17 answers2024-07-25

Hello, you need to judge what kind of reason is the reason for not ignition. >>>More

18 answers2024-07-25

1. Power supply problem: Check whether the AC power plug indicator is on, and first eliminate the problem of the power supply part. >>>More

14 answers2024-07-25

First of all, we need to know which reasons are not easy to start and are related to temperature. >>>More

12 answers2024-07-25

The gas stove can't catch fire, it may be that there is a problem in these 3 places, and you can solve it yourself, which is super simple. >>>More