When decorating, I found that the ground was rough, is there any way to make the cement floor smooth

Rough houses are like this, cast-in-place concrete floor will do a ground mortar screed layer before handing over the house, it is brushed, so it does not need to be smooth, the decoration floor tiles can be directly paved, and the place where the wooden floor is installed should be made again Mortar screed, and the wooden floor is installed after drying. So, don't do anything useless, just leave it to the decorator to deal with.

Sweep the floor and sprinkle it with water. Then adjust the cement can add some glue and favorite color, and the powder will be on the floor after adjustment, and the whole floor will be smooth and bright.

Concrete floors can be calendered, or self-leveling can be laid on cement floors.

Isn't it nice to have such a problem in the early stage after laying the floor tiles or wooden floors behind this?

This can be done with floor paint.

Which is clean again.

And a lot can be done.

After all, this is not a one-sentence question.

If you want to make a cement floor smooth, there are only two methods, sanding or using hardener. If you don't have high requirements for the ground, then polishing will do; But if you have higher requirements for the ground, then it is more cost-effective to use a hardener, such as Bang Ground hardener can not only improve the brightness of the ground, make the ground smooth, but also improve other properties of the ground.

Isn't there that kind of material for mending the ground now? You can ask.

Smooth treatment method of cement floor

1. Use concrete sealing curing agent. After the cement floor reaches sufficient strength, a layer of concrete sealing curing agent material can be evenly coated on it, which can penetrate into the cement floor for 5-8mm to improve the hardness and compactness of the cement, and then polish and polish.

2. Self-leveling process. A layer of self-leveling mortar can be paved directly on the base floor, and the thickness needs to be greater than 5mm. After drying thoroughly, the finishing layer is treated, and it can be used normally after 24 hours.

3. Add cement slurry to smooth out. Add a layer of cement slurry to the ground to smooth it, you need to chisel the original cement floor, that is, increase the contact area, and then clean it, the cement must be mixed with sand, otherwise it is not smooth and easy to crack.

4. Polishing with a polisher. The cement floor is polished with a grinding machine, and the cement floor is polished on the basis of the new and old cement floors through mechanical grinding and polishing, and then a series of auxiliary construction is carried out to make the original cement floor smooth.

5. Remove the unsmooth ground. Use a shovel axe to remove the hollow surface layer of the cement floor, or use high-strength cement or epoxy mortar to repair and level the floor position obtained by the pothole tunnel.

6. Paint treatment. The cement floor is not smooth and can also be painted, painted with color, or directly waxed, the product is sprinkled directly on the ground, and the product penetrates into the concrete base to produce a chemical reaction to form dense crystals to achieve the effect of hardening and brightening.

1. If you want to paint the cement floor, it is best to choose epoxy resin paint, which is more suitable for ground painting. 2. During construction, you can choose epoxy resin paint, or you can add curing agent according to the proportion, and then construct after stirring evenly. At the same time, it can also be doped with some epoxy diluent, which can adjust its viscosity.

Related information: 1. And the ground needs to be cleaned in the early stage, and at the same time, it is necessary to polish, cooperate with the water mill, and then cooperate with the diaphragm to polish the ground flat, or you can directly soak it with paint stripper and then shovel it and wash it with water. 2. Next, apply epoxy resin paint, and first apply the first layer of primer.

Wait until it is dry, then sand and then apply it a second time. After multiple processes, the paint film effect can be better, and the problem of cracking and falling off can be avoided in the future. 3. There is a water-based epoxy floor paint, and another is an oil-based floor paint, the former is a resin floor material formed by using water as the medium.

If you compare the difference between the two, the former one may be more environmentally friendly and more stable, so the underground garage or public place will basically use this water-based epoxy floor paint. 4. During the construction, you first need to choose qualified products, which are produced from regular manufacturers, and the quality is clear, and harmful substances will not be added, it is non-toxic, environmentally friendly products, and the damage to the human body will be the least in the later stage of nature.

There are several ways to make a rough concrete floor smooth. It is more common to repair the damaged part and then re-calender it. However, there is a certain flaw in this law, that is, the problems will be repeated, and it will not take long for the old problems to beckon to everyone.

The effect of Cronfer concrete sealant curing agent.

Therefore, most factory workshops with relatively high work intensity will directly construct the floor and solve the problem at one time, why not. At present, owners are favored to construct concrete sealing and curing agent floors, which can improve the hardness, wear resistance and other practical attributes at the same time, but also make ordinary cement floors into a smooth effect, and the appearance of the floor is also rising.

First, use a grinder to polish the cement floor;

Use a shovel axe to remove the surface layer of the cement floor with hollow drums;

Use high-strength cement or epoxy mortar to repair and level the floor position obtained by the tunnel with potholes;

The construction is carried out according to the normal resin coating process.

Concrete floors become smoother:

If it is short-term, it needs to take effect immediately, and you can sprinkle some petroleum jelly lubricant on the ground; If you want to do it for a long time, you can do floor paint first, or you can use an electric polisher to polish it with water, and finally grind it with a layer of wax.

The cement floor is a ground paved with cement mixed concrete, which is more wear-resistant, but not beautiful enough.

The use of self-leveling, epoxy paint, a small area and the floor of the ** is almost the same. Self-leveling is a solvent-free, self-leveling, dense particle high-build epoxy floor coating.

You need to chisel the original cement floor, that is, you need to increase the contact area, and then clean it, and the cement must be mixed with sand when it is on it, otherwise it is not smooth and easy to crack. A ratio of cement and sand of 2 to 1 is fine.

The situation you described is "turning sand", which is caused by the insufficient strength of the cement mortar floor at the time of delivery, it is not recommended to add a pure cement mortar plastering, if the strength of the floor mortar is not low outrageously, it is recommended to use adhesive tiles for decoration, if the strength of cement mortar is very low, it is recommended to chisel all the direct adhesive tiles.

The strength of the cement floor is not enough, resulting in the phenomenon of ash and sand, and now there are many such cases on the market, so we have developed a special product for dealing with ground ash and sand, and the product is sprinkled directly on the ground, and the product penetrates into the concrete base to produce a chemical reaction to form a dense crystal to achieve the effect of hardening and brightening. If you need help, you can find me with my username.