How to operate the fake bricks on the exterior wall, how to make the fake tiles on the exterior wall

If the fake brick operation of the exterior wall is used, there is only the feeding joint, I will teach you to 1 pour 2 5 water into the bucket 2 put the mixer into the bucket, and then slowly pour in the caulk 3 Start the mixer and stir for about 3 minutes, stir the water and caulk evenly, add caulk and water appropriately according to the consistency, until the caulk is adjusted to a paste with a certain fluidity 4 Put the glue nozzle in the conical bag 5 Pull the glue nozzle out of the cone bag until it is clamped tightly6 Use a blade to cut off a part of the top of the nozzle according to the width of the caulking to be filled, Make the cut bevel basically consistent with the width of the caulking 7, put the finished bag into the hard rubber hose 8, and turn it outward to cover the hard rubber hose when 1 3 is left, pour the adjusted paste caulk into the hard rubber hose with a spoon, and lift the bag after it is almost full, twist the back of the bag with your hand, and squeeze out the caulk in front of the nozzle a little, the purpose is to drain the air inside, drag the glue nozzle to the seam to be filled from right to left, and at the same time squeeze out the caulk in the bag with the afterburner of the other hand, and feed it evenly into the transverse seamThe same method, let the rubber nozzle move down to feed the vertical joint, this is the appearance of the horizontal seam and the vertical joint are fed after feeding, after feeding the seam according to the weather conditions about 2-3 hours later, when the fed caulk is almost dry, use the joint tool to pull up and down the vertical seam, so that the pressed seam into a semi-concave arc, the same method to pull and press the transverse seam left and right, after all the tension and compression are completed, clean the brick surface with a plastic broom, and sweep the caulk sticking to the edge of the brick (because the caulk is basically dry, so it will not pollute the wall, At the same time, the caulk that is swept out can be collected and reused).

Is it an imitation brick for the exterior wall? Is the putty the one you do after you scrape it?

Depending on which one you want to ask, it is generally GRC and GRH, which can imitate marble, sandstone, stone, travertine, and wood. All of them have special treatment processes.

Brick laying ** is generally about 18-25 yuan, but the exterior wall is more expensive than more than ten yuan, and there are more patterns, and the process is more complicated, the cost may be higher. Repair the seam for additional money.

This piece is not very clear, only the people who are looking for the roadside construction team are still clear.

Are you talking about imitation stone effect imitation natural stone, rock chips, imitation brick paint? It is recommended that you use Chenguang paint, generally speaking, the price of this piece of real stone paint is 280 yuan barrel, a barrel of 30 kilograms.

The interior wall and exterior walls are not connected, the windows are wrapped in newspaper or plastic sheeting, and then the windows are closed, and it is also possible to paint at the same time. The flooring is indoors, so it is OK to paint the interior walls after 48 hours.

The new house should be plastered at the base level, and after drying, it should be done, and then the exterior wall paint should be done. The color should not be too dark, but bright and bright, such as: white, off-white, beige.

Parts can be paired with dark colors. Choose by style. The overall color palette refers to the surrounding environment.

Private houses can also be used to create brick patterns of various sizes using the hook seam method. Safety scaffolding should be erected for exterior wall construction, and layered construction should be carried out from top to bottom. There are two main categories that are commonly used now:

Real stone paint. Colorful.

It is difficult to deal with, the adhesion is too poor, and it has been encountered once in the construction of the project, which is the first to clean the dust of the brick surface, and then use polymer mortar as the base, paste a layer of 500 grams of glass wire mesh cloth, and after the polymer putty is leveled, brush the acrylic exterior wall paint three times, but it is not resistant to collision.

Exterior wall tiles are mainly used for the decoration and protection of building exterior walls.

Renderings of exterior wall tiles.

Renderings of exterior wall tiles.

The main specifications are 25*25mm, 23*48mm, 45*45mm, 45*95mm, 45*145mm, 95*95mm, 100*100mm, 45*195mm, 100*200mm, 50*200mm, 60*240mm, 200*400mm, etc. Exterior wall tiles can be sold in stock or customized according to customers' special requirements for specifications and colors. Exterior wall tiles not only decorate the entire building, but also play an important role in protecting the wall because of their acid and alkali resistance, stable physical and chemical properties, and can also prevent cold and heat preservation.

In order to meet the requirements of individuality and richness of exterior wall decoration, exterior wall decoration technology and techniques are developing towards high grade and high grade. The exterior wall tiles pay attention to the overall matching, rich decoration techniques, diversified decoration styles, and outstanding decorative effects.

I hope my answer can help you.

Imitation brick coatings are generally used in real stone paints and texture coatings, which are anti-fouling and dirt-resistant.

First of all, find the horizontal line, fill the water with a transparent thin water pipe, and leave a little empty at both ends not to fill it (the water in the pipe should not have air).

Select any point in the corner of the wall where you want to put the wall tiles as the base point (this can be the height of the lowest tile or arbitrary).

One person presses the end of the water level at one end of the pipe on the base point (let's say point A) and the other person takes the other end and holds it down on the corner of the other wall (let's say point B) and moves it up and down When the water level at point A overlaps with the base point, stop Point B makes a marker and plays the ink fountain line, so that a flat water line comes out.

When tiling, you only need to use the line as the basis to measure with a ruler or a square ruler to determine the basic level of all tiles.

When pasting, it is best to pass through three lines, one horizontal seam, one vertical seam, and one brick surface.

Use a special light source pay-off equipment, if you don't have it, use the gravity pendant to find the vertical line, and use the horizontal tube to find the horizontal line...