Are there any requirements for floor tiles? What are the requirements for home improvement tile pavi

Whether it is wall tiles or floor tiles, it needs to be moved from outdoor to indoor for 24 hours, and can only be paved when it adapts to the indoor temperature, so as to avoid hollowing and falling off after construction. In addition, the joints should be hooked in time after the brick is paved. Make sure the tiles absorb enough water.

Floor tiles are the first choice for most families to decorate and decorate bathrooms, kitchens, living rooms and balconies. In the winter construction, the water temperature of the soaked brick should not be too low, only in this way can we ensure that the tile absorbs enough water, so that the brick will not be bonded to the cement due to the absorption of slurry water during bonding, resulting in hollowing and falling off. Attention should be paid to the following:

When carrying out the isothermal operation of building walls, sticking wall and floor tiles, and laying marble, the cement has no solidification force due to freezing, and after thawing and drying naturally, the walls and floor tiles will be shelled or peeled off naturally.

When making wood products, if you use white glue to bond, you should pay attention to the performance of white glue, because it is likely to affect the bonding strength due to freezing. When making paint, because the temperature is too low, the curing time is long, but it does not affect the construction, in case of continuous rain, then it is best to avoid paint construction. When pasting wallpaper or brushing wall paint, due to freezing, wallpaper glue and paint will appear frozen, at this time, you must not use boiling water to mix and heat or use other ways to heat, boiling water will dilute the glue, so that the viscosity of the glue will decrease significantly; Warm with water, although the glue can be smeared, it will freeze immediately after being put on the wall, resulting in uneven application and lack of stickiness, which greatly affects the quality.

Winter construction must also pay attention to safety, construction personnel must not use electricity, gas to heat, so there will be life danger, do not in order to catch up with the schedule, in the room with gas heater or small sun lamp to raise the indoor temperature, this practice belongs to uncivilized construction, not only affect the quality of construction, but also very dangerous.

In fact, the floor tiles can be retained during the decoration, the old floor tiles are used to lay the wooden floor on the bottom, and the wooden floor is not impossible, but the dust on the floor tiles needs to be cleaned up, and the floor tiles can be used to ensure the smoothness of the indoor ground, and it is easier to lay the wooden floor on it, so as to dismantle the old floor tiles, speed up the decoration progress, and save the decoration expenses at the same time. But laying wooden floors on the floor tiles, you need to check whether the floor tiles are loose, if there is a loose need to fix it, but also measure whether the floor tiles are paved level, if it is not flat, it needs to be corrected, otherwise it will affect the laying quality of the wooden floor, increase the space of the floor and the space without the floor, their ground has a drop in height, and the treatment of the joint should be done well, so as not to affect the appearance.

Temperature is the primary factor affecting the tiling in winter, and factors such as dry air and large temperature difference between indoor and outdoor increase the difficulty of tiling in winter; Secondly, the water absorption rate of different types of ceramic tiles is also different, such as stoneware bricks greater than 6% less than or equal to 10%, porcelain tiles less than or equal to; In addition, the temperature control of the construction personnel during the paving process will also cause problems such as hollowing, falling off, cracks and poor bonding. Process construction. Don't rush the deadline.

Many owners ask the decoration company to rush to work in order to move in early due to individual circumstances. Here Shichuang reminds everyone that ceramic tile construction has its own time limit, do not rush the construction period, and even, when the temperature is too low, you should also consider suspending the construction, because the tile paving temperature is too low to directly pave the quality. It is necessary to control the temperature and replenish water.

Ceramic tiles in modern home decoration are already well-known decoration materials, and there are many types of ceramic tiles, including: full glaze, vitrified tiles, microcrystalline stones, antique tiles, mosaics, full-body bricks, etc. The paving method of each tile is different, and the need to pay attention to it is different, but the overall is similar, what are the requirements for home decoration tile paving?

The following is a brief introduction to what are the requirements for home decoration tile paving.

1. When paving tiles, soak and transport quiet water as needed.

The tiles that have been soaked in water affect the secondary sales, and the manufacturers and merchants generally cannot return them, which will cause unnecessary waste. Suggestion; It is necessary to combine the construction progress of the workers, and run as much as they need to run to avoid waste.

2. Make a plan to shoot tiles before paving.

Many construction workers paved the bricks as soon as they got them, and when they reached a certain level, they found that the proportions were not coordinated, so they had to remove them and re-pave them, resulting in unnecessary waste. Suggestion: Make a plan for arranging tiles before laying them.

3. Remind workers to notify them in time if they find problems with the quality of ceramic tiles during the construction process.

A lot of friends are always in the paving after the discovery of the problem, and then the construction party and the material side shirk each other, causing unnecessary disputes, it is recommended that in the construction to clearly tell the workers, once found that the tile problem is notified in time, so as to avoid unnecessary disputes.

4. Correctly mix the ratio of cement and sand.

The proportion of cement is large, and the bricks can be quickly tackled, but the expansion coefficient of cement mortar is large, and it is easy to squeeze the bricks after paving. Suggestion: Mix the ratio of cement and sand to 1:3 for wall tiles and 1:2 for floor tiles.

5. Be careful when processing ceramic tiles.

When re-building the wall in the sunny corner, be careful not to destroy the glaze layer of the tile, pay attention to the gap should not be too small when connecting, and some tiles that need to be cut are best to be delivered after the material supplier cuts them when buying.

6. When dealing with the flue, the masonry wall must be standardized.

The large core board can not be used as the wall material for re-building the wall, and the tiling is easy to cause the tile to arch, fall off and crack.

7. The seam of the tile should not be too small.

The gap of the tile is too small, which is easy to reduce the service life of the tile, and the tile cracks the glaze when it is heated and expanded. Suggestion: Whether there are seamed tiles or seamless tiles, pay attention to the gaps when constructing, and it is best to ask the material supplier how much gap you need to leave when buying.

8. It is best to wait for the tile to dry and solidify.

If the tile is not completely dry, the ridge will be filled immediately, and it is easy to loosen the tile due to the slag, and even cause the tile to fall off in the later stage, leaving hidden dangers. Suggestion: Grouting should be carried out after the tile has dried, usually after 24 hours.

9. Do a good job of protection when paving tiles, do not scratch or pollute the brick surface, do not walk around on the brick surface that has not dried up when doing wall painting and coating, otherwise it will cause damage to the tiles.

Summary. Hello dear, according to the situation you described, the main paving tiles include tiles, and cement sand, tiling, and caulking. These items are covered with tiles including ranges.

Hello dear, according to the situation you described, the main paving tiles include tiling, and filial piety cement sand, tiling stuffy sails, caulking. These items are all covered by tiles and canopies.

Hello dear, according to the situation you described, 1. Wave line laying method This paving method is also called lace or wave guide wire, edge line, etc. This paving method is mainly used around the ground or in the entrance, etc., and is used as a decorative line made around the wall along the floor floor, and the width is different. This paving method has lines that are different from the overall floor color to increase the design effect.

2. Traditional paving methodThis paving method is the most traditional paving method. It should be noted that the laying should be paved in a parallel way to the wall, the brick joints should be aligned and can not be left joints, and at the same time, the joints should be grouted with a grout similar to the color of the bricks, so that it looks refreshing, neat, generous and decent.

3. The I-shaped paving method is slightly modified in the traditional paving method, and it is not paved in a straight line according to the method of passing the rough side, but is changed to an I-shape. 4. The dislocation method is to rotate the square laying method by 45 degrees, which is a bit similar to the traditional paving method, and its straight line is very smooth, and the infinite extension has a good visual impact.

Summary. Choose polished tiles for paving.

Choose polished tiles for paving.

What tiles are good for paving.

Polished brick is a kind of bright brick made by polishing the surface of the whole brick body, which belongs to a kind of whole body brick.

Polished brick belongs to no radioactive elements, natural stone is mineral, long-term contact with the human body will not cause harm to the human body, basically controllable no color difference, polished brick is carefully deployed, the same batch of products are the same, basically no color difference belongs to the natural stone shape sold Zheng Cheng, polished brick anti-bending and aging strength, can withstand very heavy pressure The brick body of polished brick is thin and lightweight, and the processing and construction are very convenient to throw and match the surface of the polishing brick is smooth and bright, and the most important advantage of the decorative effect is that the anti-slip performance of the polished brick is good. It is a good choice of tiles for home decoration.

Categories: Life >> Home improvement.

Problem description: How to lay floor tiles.

Analysis: The construction process of the ground paste floor tiles is as follows:

Base treatment - plastering cake, punching - cushion - plastering mortar - pasting ceramic floor tiles - leveling joints - cleaning - curing.

1.Reinforced concrete floor slabs.

2.Plain cement slurry is combined with a layer.

Thick 1:3 cement mortar screed, surrounded by small figure-of-eight corners.

4.Water emulsion rubber asphalt waterproof coating, one cloth and four waterproof layers, rolled up 150mm high all around, coarse sand sticky outside, and 300mm wide at the door.

5 40-50 thick 1:2:4 fine stone concrete from the door to the floor drain to find flooding, the lowest point is not less than 30mm thick.

6 20mm thick 1:4 dry hard cement mortar bonding layer.

7 plain cement bonding layer.

8. Remove the cement surface (sprinkle with an appropriate amount of water).

9 8-10mm thick paving floor, dry cement wiping joints.

Key points:1If the base layer is a concrete floor and ground, and it is relatively smooth, it should be chiseled, the depth is 5-10mm, and the spacing of chisel marks is about 30mm.

surface residual mortar, dust, etc., and rinse.

2.Springline, positioning:

1) Diagonal positioning method - the brick joint is at an angle of 45 degrees to the wall corner.

2) Right angle positioning method - the brick joint is parallel to the wall.

When playing the line, pop out the positioning lines perpendicular to each other with the center of the room as the origin, and pay attention:

1) Leave 200mm-300mm from the wall to adjust the range.

2) If the floor tiles inside and outside the room are of different varieties, the handover line should be in an inconspicuous place.

3.Set the standard height of the ground, make a T-shape for the smaller room, make a cross shape for the larger room, and paste two rows of floor tiles.

4.When paving, the cement slurry should be hung on the back of the tile full, and hammered with a rubber hammer, and the side of the paste should be checked and corrected with a level, and the cement slurry on the surface should be wiped off immediately.

5.After 2 hours of curing after paving, dry cement is used to wipe the joints and wipe the surface of the tiles.