-
When a developer builds a house, the material cannot be used exclusively as a brand. Owners need hardcover before moving in. During the renovation process, the bathroom was concealed and the upper and lower water pipes were installed on the walls.
Once there is a quality problem, it is difficult to find, and after a long time, it will slowly penetrate in, and in the decoration process, the semi-tone, water and electrical materials of the wall will choose a large brand. Quality*** Bathroom waterproofing is key. The waterproofing effect is not ideal.
When bathing, before the water penetrates into the opposite side of the wall for waterproofing, please find a flat mortar with the gold altar surface, evenly coat the wall and floor, find a flat plaster, and do not apply it too thickly. Evenly choose the thin ones and you're good to go. In this way, it has a smooth effect on subsequent waterproofing.
It is waterproof after drying as a whole.
Generally, the bathroom is waterproof three times, the front waterproof and dry can be done again, the difficult part of waterproofing, the joints around the corner of the wall are evenly coated with waterproof paint, and the front waterproof can only be done again after drying, the kitchen is also the place with the most water, the wall is still waterproof after the resurgence, in order to fundamentally solve the problem of semi-tonality, this problem is more troublesome, the toilet upstairs in my house has penetrated my home, and as a result, the floor of other people's toilets has been planed off, and the floor has been done very well after finding a leaky place. Of course, I also paid some money, after all, it was a neighbor. If the moisture returns, I recommend reopening the damp walls and doing waterproofing.
How to deal with the moisture on the walls during the renovation process? Where will the walls regain moisture? What causes moisture?
Because it is found during the renovation process, it is possible to find the reason for the moisture to come back and deal with it in a targeted manner. The reason for the moisture coming back is mainly 4 points. The exterior wall is waterproof, not waterproof, there is a problem with the river, and there is a problem with the construction process.
Waterproofing requires exterior walls. Where there are windows, be careful not to allow water to penetrate the edges of the windows. It can be found in the area of water.
Then do the waterproofing project and do the closed experiment. The waterway is again subjected to a pressure test to check the connection of the attachments. It's hard to say.
Use a dehumidifier. The room is damp, and desiccant and activated carbon can be used to prevent moisture and absorb moisture. Desiccants and activated carbon can be used.
There are many desiccants in supermarkets that are only used for moisture-proof and dehumidification, and the most common are two types: hygroscopic boxes and dehumidification bags. Buy an air inhaler. It collects moist air like a vacuum cleaner, and when it is wet, it turns into water.
Use an air conditioner to remove moisture. Air conditioners used at home generally have a dehumidification function, but the way the air conditioner regulates the humidity of the indoor air is slower, usually taking 2 to 3 hours, making the people indoors feel cold. The use of lime and bamboo charcoal dehumidification.
The small bag contains an appropriate amount of lime, tied to every corner of the room with a small bag, the lime itself has the effect of absorbing moisture, which can slow down the damp state in the room, and at the same time, the lime also has a disinfection effect, killing two birds with one stone. Bamboo charcoal dehumidification can be used repeatedly, but it should be used more, and the effect is not very good. Doors and windows should be closed to prevent moisture.
Usually open more windows for ventilation to reduce indoor water vapor content. In particular, the newly renovated house has a lot of moisture, and the ventilation should remove more moisture.
-
You should find a special renovation company to help solve such a problem. In this way, the dampness of the wall can be effectively solved.
-
In this case, you have to find someone from the decoration company to solve it for yourself, because it is caused by their improper operation, which is no longer something you can solve.
-
At this time, it is likely that there is a water leak upstairs, and it is necessary to communicate with the upstairs, and also invite professional personnel to repair the walls added by themselves.
-
Open all windows in your home to allow good air convection to ventilate so that damp walls can be dried.
-
It's best to ventilate the room quickly and evaporate the moisture, if it doesn't work, then you can only shovel off the wall skin and do it again.
-
The new house that I just got my hands on should be said to be lovely. But many friends who live in the south have the problem of returning to Nantian. Even the walls of a new house are damp, and if you put wallpaper, you will even soak the wallpaper, and when the weather clears, the wallpaper will be dry and brittle.
Today, I will tell you what to do if the wall of the new house is damp, and what are the skills of the wall treatment and moisture-proof.
1. How to resist the old when the wall of the new house is damp.
1. Open more windows for ventilation.
First of all, we can take the method of opening the window for ventilation, if the wall has a resurgence of moisture, it is recommended to open the window for ventilation when the weather is fine, and discharge the indoor moisture to the outside, if it is rainy, try to close the doors and windows, so as to prevent the indoor humidity from aggravating.
2. Replace the wallpaper in time.
Secondly, if the wall in the room has regained the moisture and the wallpaper has also been damp, then the entire background will look extremely unstable, and it will be distorted or even discolored. In addition to ensuring that the entire wall is not damaged by more moisture, it can also ensure the beauty of the wall, but this method may be more troublesome.
3. Dehumidifier.
The room is damp, and monotonic agents and activated carbon can be used to prevent moisture and absorb moisture. There are many monotonic agents in supermarkets that are dedicated to moisture-proof and dehumidification, and the common ones are two types: moisture absorption boxes and dehumidification bags.
Second, what are the skills of wall treatment and moisture-proofing?
1. The kitchen and bathroom are drained and cause moisture.
If it is because of the dampness of the wall caused by daily splashing water in the kitchen and bathroom. This situation is a common one when the wall is damp. In particular, the walls under kitchen cabinets and bathroom cabinets are more prone to this kind of dampness.
This may also be caused by splashes of water from washing vegetables and dishes along the walls of the kitchen cabinets and wetting the walls. It is recommended to use glass glue to fill the joints of kitchen cabinets, bath cabinets and walls to prevent water flow, and the phenomenon of wall moisture return can eliminate the rise and loss of the base.
2. Do a good job of waterproof and moisture-proof walls.
Don't think that only kitchens, bathrooms, and balconies need to be waterproofed, and the walls and window sills separated from the kitchen, bathroom, and balcony should also be waterproof and moisture-proof. Due to the long-term invasion of moisture or water vapor, these places are particularly prone to mold, peeling, and peeling.
The above is the relevant information that I will share for you what to do if the wall of the new house is damp, and what are the tips for treating the wall with moisture, I hope it will help you.
-
The walls of old houses are susceptible to moisture, and moisture protection is a very important issue for people who are decorating old houses. If corresponding moisture-proof measures are not taken, the dampness of the wall can easily cause the growth of various bacteria and molds, which poses a threat to human health. Here are a few ways to prevent moisture.
1.Fill putty or guess the base layer: First of all, you need to ensure that the wall is flat and smooth, you can polish the original base layer to remove burrs, swelling, mold, etc., and then paint the filling putty to ensure that the wall is flat and smooth.
The material of putty can choose products with good water resistance, which can effectively isolate moisture penetration.
2.Spray waterproof paint: After applying the filler putty, choose to spray waterproof paint. The waterproof coating can achieve moisture-proof effect, and the paint film spike has the advantages of smooth and flat, anti-cracking, etc., and the service life is relatively long.
3.Waterproof coating on the top surface of the block: Before renovating the top surface of the old house, a layer of waterproof coating can be applied to the top surface to effectively avoid rainwater infiltration.
4.Use a moisture-repellent treatment: You can use a moisture-repellent treatment when painting the walls or renovating the house. This treatment can form a layer of water insulation on the surface of the wall, preventing moisture inside the wall.
5.Drainage: Drain the drain so that rainwater and groundwater don't flood into the room. At the same time, when using electric fans or air conditioners for heating indoors, pay attention to ventilation to ensure that indoor moisture is discharged in time.
To sum up, moisture protection is an important issue in the renovation of old houses. Before decoration, it is necessary to carefully check whether the wall is damp, and use corresponding moisture-proof measures to treat it, keep the wall dry, and ensure the quality of the house.
-
The walls of the new house are damp, and the tips for dealing with moisture-proof: If the room is damp, you can use moisture-proof agents and activated carbon to waterproof and absorb moisture. Moisture-repellent and activated carbon can be used.
There are many moisture-proof agents in supermarkets that are only used to repel water and moisture, and the most common ones are absorbent boxes and dehumidification bags. Buy a gas inhaler. It collects humid air like a vacuum cleaner, and turns into water when it is wet and cold.
Use ** air conditioner to remove moisture. The ** air conditioner used at home generally has a dehumidification function, but the actual effect of the air conditioner to adjust the indoor air quality and environmental humidity is relatively slow, generally 2 or 3 hours, so that people in the room feel cold.
Application of lime powder and bamboo carbon dehumidification. The small bag contains the appropriate lime powder, tied to every corner of the room with a small bag, the lime powder itself has the effect of digesting and absorbing the moisture in the body, which can relieve the damp and cold situation in the room, and at the same time, the lime powder also has the effect of disinfection and sterilization, killing two birds with one stone. Bamboo charcoal dehumidification can be used many times, but it should be applied more, and the actual effect is not very good.
Doors and windows should be closed to avoid moisture in the body. Usually more indoor ventilation should be used to reduce the water vapor content in the room. Especially in the newly renovated house, the moisture is very large, and the natural ventilation should remove more moisture.
Buy a gas dehydrating breather, which acts like a vacuum cleaner to concentrate the wet gases together until the dampness in the body turns into water at some point. Use the air conditioner dehumidification mode. The ** air conditioner used at home generally has the effect of dehumidification, but the method of ** air conditioner to adjust the indoor air quality and ambient humidity is relatively slow, generally two or three hours, and will make people in the room feel cold.
Use lime powder and bamboo charcoal to dehumidify. Use a small cloth bag to pack the appropriate lime powder, tie it into a small bag and place it in every corner of the house, the lime powder itself has the effect of being damp, and can also alleviate the indoor dampness, at the same time, the lime powder also has the effect of disinfection and sterilization, killing two birds with one stone. Bamboo charcoal can be used repeatedly to dehumidify, but it has to be commonly used, and the actual effect is not very good.
Common problems: internal and external wall waterproofing first do a good job of moisture-proof wall, after the wall is hooked with tiles, carry out exterior wall waterproof material brushing, so that the wall does not leak, and the internal and external walls will be waterproof. At home, you usually need to pay attention to the application of water resources, you don't have to make tea often, and the damp and cold in the room can be solved by using ** air conditioner to carry out dehumidification.
The outer wall waterproofing should first remove the bottom layer, the surface layer should be tamped and leveled, there can be no looseness, sanding, peeling, in order to prevent harm to the bonding strength, and the bottom layer should be dry when brushing waterproof materials.
-
It needs to be renovated, the damp area needs to be removed, and then the specific wall condition is determined, and the plaster is reapplied, preferably with some waterproofing material.
-
The walls of the new house should be ventilated as much as possible when they are wet. In rainy weather, doors and windows should be closed. When it gets wet, it needs to be refurbished.
-
If this situation occurs on the wall, it must be re-treated, and the exterior wall and the interior wall need to be treated together, and some wall materials must be painted to make waterproofing.
-
Damp walls after renovation can easily cause people to be troubled, mainly because it can have a serious impact on indoor air quality and may even cause health problems. In order to solve this problem, we need to first find out the cause of the dampness on the wall, and then take targeted measures to deal with it.
1.Poor indoor ventilation. If there is a lack of circulating fresh air in the room, the walls are prone to moisture accumulation, leading to dampness. Therefore, after the decoration, it is necessary to keep the indoor ventilation as much as possible, and if possible, you can often open the window for ventilation to avoid a humid environment.
2.The wall building materials are unqualified. If the building materials of the wall are not up to standard, such as the surface paint contains excess water, then in the case of poor ventilation, the wall will be damp. At this time, it is generally necessary to replace the building materials to avoid unnecessary trouble.
3.The foundation is unstable. If the foundation is unstable, the groundwater will seep into the wall during the subsidence of the building, resulting in dampness of the wall. In this case, the foundation needs to be repaired or replaced in time to ensure the stability of the foundation of the house.
4.The paint is peeling off. If the paint does not meet the quality standards during the decoration, it is easy to be damaged and fall off. At this time, the paint that has penetrated by moisture should be treated in time and recoated with the paint that has been refreshed.
In short, for the damp situation of the wall, we need to find out the cause first, prescribe the right medicine, and take effective measures to deal with it. After the renovation, ventilation should be carried out in time to ensure the comfort, health and safety of the living environment.
The new house has just been renovated, and the frequent water leakage after moving in is because the original waterproofing has not been done well, or the pipeline has not been tested for pressure, so water leakage often occurs.
The harm of formaldehyde is well known, and now there will be formaldehyde residues in newly renovated rooms, and we should take timely measures to minimize the content of formaldehyde to reduce the harm to the human body. >>>More
In fact, it has no effect, because the formaldehyde content in the new house should be relatively high.
Don't worry about staying, you should do a series of formaldehyde treatments. Opening windows for ventilation is not enough. You can put some activated carbon to remove formaldehyde, because activated carbon can effectively remove harmful substances such as formaldehyde. >>>More
If you are looking for a professional formaldehyde treatment company to deal with it, you can find Suzhou Kobride Environmental Protection They use the treatment method of photocatalyst, which has a good effect and no secondary pollution. >>>More