When renovating a kitchen, can you use structural adhesive tiles on the flue?

The glossy panel itself is thin and has weak adhesion. If the tiles are painted directly with mud or ceramic tiles, the pipe will be affected by thermal expansion and cold contraction in the later stage, and the pasted tiles will also fall off easily, which is a safety risk.

It needs to be repaired later, so it's too much trouble. Therefore, if a developer develops a pipe made of a glossy panel, the tile will have to be thickened. Placing a circle of red bricks along the cigarette sticks made by the developer can prevent the problem of tiles falling off in the later stage and improve the adhesion between the tiles and the cigarette sticks.

The actual installation of the smoke valve is divided into four stages, also known as the standard four stages, if you can't reach this construction and installation stage, it is a joke to prevent coma!

The smoke valve is mainly automatically opened and closed by the wind caused by the flow of the pipeline itself, which belongs to an automatic valve. The flue valve is the guardian of smoking cessation at home, which is small in size, but has a great effect and directly affects the mood of living. The smoke valve can effectively prevent the gases and fumes from the homes of the middle and lower classes of people in the public flue, which is often referred to as a distortion phenomenon.

Mosquitoes, moths.

Flying insects such as flies and reptiles such as lizards.

They can prevent them from entering the home, and most importantly, they can keep the air inside the home hygienic and safe. Fire chimney check valve.

It is the most reliable product at present, and fully complies with the regulations of the State Environment Administration and the State Fire Administration. This type of smoke valve is often used by developers in residential construction, installed in kitchens, with average sound insulation, but environmental protection and safety are fully in line with standards.

The iron pillar of the plastic structure penetrates the valve blades, the valve body is square, and it needs to be perforated and installed, and its material is cheap, easy to install, and the smoke-proof effect is general. Plastic check valves are made on the same principle. The whole is made up of stainless steel or unrusted iron.

It needs to be installed through holes, which has the advantages of one-way fire prevention and general smoke prevention effect, and many developers also use check valves of this material. 5. Defend yourself.

The annual check valve is the most reliable check valve product in the flue high-end residence, referred to as the 5 self-proof valve, which has an erection effect and 5 self-defense effect, and is known as the variable pressure erection smoke check valve. The design of the jet plate effectively avoids defects such as gas negative pressure and poor ventilation caused by vortex.

Installation in the correct flue position is a prerequisite to prevent stranding, so it is correct to install the smoke valve on the auxiliary flue. The flue of the kitchen is actually divided into the main pipe and the auxiliary pipe. The difference between the two is simple.

The main flue connects the kitchen throughout the building, is shared by all landlords, is generally vertical, and the pipe diameter is relatively thick. Upstairs and downstairs all the neighbors where the fumes gather, the burden boat route is used separately by each family, which is smaller than the main smoke, and the burden boat route is often external.

When decorating the kitchen, the flue can be tiled with structural adhesive, or with cement tiles, both methods can be used, depending on which is convenient.

No, you cannot. Because if you use structural adhesive to paste tiles, the tiles are not particularly firm and easy to fall off.

No, because in such a high temperature situation, the molecular structure of the structural adhesive will be destroyed, causing the tile to fall off.

No, it needs to be thickened.

Carry out flue thickening treatment, and build a layer of brick wall around the flue with sand bricks, which can first avoid the tiles from falling off easily after a long time, and secondly, enhance the adhesion ability of the tiles to the flue.

Because most of the original flue developers are made of mineral wool board, the thickness is very thin, the heat permeability is very high and the adhesion is not high, if the surface is pasted with tiles, there will be a very large drop of thermal expansion and contraction, and the tiles are very easy to fall. There are also some practices that use plastering techniques, using cement mortar for surface plastering, thickening the thickness of the surface layer of the flue, and insulation, but it may also produce delamination.

Tile on the kitchen flue, these problems can not be prevented, and only once and for all can be done well!

OLY-3102 strong tile adhesive.

Scope of application. It is suitable for indoor and outdoor concrete or cement mortar substrates, tiles, marble, granite, and mosaic pasting.

Features: It has good water retention, impermeability and anti-aging properties.

Excellent flexibility, small shrinkage, not easy to crack.

The construction is simple, there is no need to soak the brick wet wall, and the work efficiency is high.

The adhesive layer is thin, the adhesion is strong, the material is saved, and it is uniform, and the hollowing is avoided.

Green and environmentally friendly, non-toxic and non-radiation-free.

Base surface requirements. The surface of the substrate is strong, dry, clean, free of oil, concrete curing agents and other loose materials.

Construction method. Mixing ratio: water:powder = 1:4 (kg).

1 Pour water into the container, then add the tile adhesive in proportion, stir it into a uniform, non-granular paste with electric stirring, let it stand for 5 minutes and stir for 1-2 minutes.

2 Use a toothed scraper to apply the tile glue to the base surface. Make it evenly distributed, and form a strip of teeth, apply about 1 at a time, and then knead the tile on it.

3 If the groove on the back of the tile is deep, in addition to applying tile adhesive on the working surface, the adhesive should also be applied on the back of the tile.

Precautions. 1: This product is suitable for construction in the environment of 5 -40, and the vertical and flatness of the base surface should be confirmed before construction.

2: It is best to use up the tile adhesive that has been stirred with water within 2 hours, and do not mix and stir the tile adhesive that has been dried and solidified, 3: 24 hours after the construction is completed, you can step into or fill the joint.

4: Stir well with an electric mixer. The specific gravity of water should not exceed 25%.

5: No cement, sand and other substances can be added, only water can be added to stir.

6: The thickness of batch scraping is controlled at about centimeters each time.

The adhesive of ceramic tile adhesive is very good, if you are not at ease, you can add adhesive matching with ceramic tile adhesive.

Why is the kitchen flue sticking porcelain chongxiao brick for a long time, why is it hollow, and the master tells you the reason for ruining the judgment!