How to solve the problem that the heating on the first floor is not hot, the heating of the whole bu

Some of the owners of the family live on the first floor, the key is to say that the comparison is cost-effective, and the transportation is also very convenient, no need to leave and right indoor stairs. But in winter, some first-floor owners will feel that the heating on the first floor is very sloppy. Why is the heating on the first floor poor?

What should I do if the heating on the first floor is not hot? There are many reasons why the heating is not hot, and here Jinjin will bring you the reasons and solutions for the heating not to be hot.

Why is the heating on the first floor poor?

1. Heating system reasons.

Residents on the top floor close the cut-off door completely or partially, causing the circuit to be blocked or interrupted. Another factor is the blockage of the heating system, some heating systems that have been in operation for many years but have not received the necessary maintenance and maintenance, such as blockage, leakage and other phenomena affect the heating effect of the whole system. There are also some residential areas where the original design of heat supply and heating area do not match, forming a "small horse-drawn cart", and the above problems should be solved by the property management department.

2. The heating is due to itself.

Now most residents use the old-fashioned cast iron heating, most of this heating is old, it is necessary to rely on the heating cover to dress up, the decorative effect is improved, the quality of life is reduced, "beautiful and frozen people", some residents simply open the heating cover in winter, despite this, the heat dissipation effect is still greatly reduced, if you want to heat up fundamentally, the best way is to use the new type of heating without cover.

3. The heating has the sound of water.

The main focus is on the top-in and bottom-out installation method, because there is gas inside the radiator that cannot be discharged. The solution is to close the water supply valve of the radiator, open the discharge valve, discharge the gas inside the radiator, close the exhaust valve, and open the water supply valve. If it cannot be ruled out, check whether the flow rate of the system is too low or the gas content of the circulating water of the system is too large.

How to solve the problem that the heating on the first floor is not hot?

1. Check whether there is any nest gas, water leakage, and the heating valve is not opened, and then solve it according to the specific situation.

2. If the heating below the top floor of the community is hot, you can ask the residents whether it is getting cooler and cooler from the first floor, if so, it means that the hot water for the district heating is from the first floor to the top layer up, that is, there is a problem with the design of the HVAC pipeline of the building, and you can contact the heating company to solve it.

1. If the heating below the top floor of the unit is hot, you can inquire whether it is getting cooler and cooler from the first floor to the top, if so, it means that the hot water heated by the unit where the home is located is from the first floor to the top layer up, that is, there is a problem with the design of the HVAC pipeline of the building. 2. The heating flow pipe should be exhausted, and the exhaust valve is generally installed everywhere, if the displacement of the exhaust valve is too small or broken, the air of the pipeline can not be removed in time, so that the expansion of the pipeline, so that the water can not flow or circulate. If there is no problem with the exhaust valve inspection, then check whether the pressure of the boiler and the power of the circulating water pump are up to standard.

Reasons why the radiator is not hot:

1. Whether the two locking valves and two ball valves have all been opened.

2. Whether the indoor heating facilities are covered or not affects the heat dissipation effect of the radiator.

3. Whether the filter at the entrance valve is blocked.

4. Whether the indoor radiators and pipes are exhausted one by one.

Find out which heating unit supplies heat, and in principle, who supplies and who manages. Report to the relevant units of the construction of the building, and they will be responsible for handling it. If the pipeline in the community is in disrepair or out of balance, it should be repaired and adjusted by the property rights unit.

Now radiators are gradually adopted in people's lives, so what should I do if the heating on the first floor is not hot? Next, let pchouse introduce it to you.

The reasons why the heating on the first floor is not hot are: 1. There is a problem with the design of the heating pipes, and the laying method may be in series, and the heating pipes need to be rearranged; 2. There is too much air in the heating, and the exhaust valve needs to be opened for exhaust; 3. There is a lot of dirt on the inner wall of the heating, and the heating pipes need to be cleaned in time.

First, there is a problem with the design of the heating pipe.

Sometimes the heating on the first floor, if it is not hot, may be due to the heating pipe itself when laying, there is an unreasonable design situation, some developers will set the heating in series, the way of series connection will affect the heating pipe in the heat transfer process gradually weakened phenomenon, at this time you need to contact professional maintenance personnel in time to change the pipe laying method to parallel, after entering the house divided into two ways, which can reduce the resistance of heating water in the home, enhance the effect of home heating.

Second, there is too much air in the heating pipes.

If there is more air in the heating pipe, it will also affect the water circulation, and will also affect the final heating effect, at this time, you need to close the heating valve, open the exhaust valve at the top of the radiator, and stop twisting when you hear the sound of gas discharge, until the gas is exhausted, and finally open the water inlet valve, wait for the water to flow out, you can close the gas release valve, and the action of twisting the valve should be light, and brute force can not be used, otherwise the heating pipe system will be damaged.

3. There is too much dirt on the inner wall of the heating.

Another important reason why the heating on the 1st floor is not hot is that there is too much dirt on the inner wall of the heating, and many people will not clean the radiator for a long time, resulting in more and more scale inside, which will also affect the water circulation and finally affect the heating effect, so it is necessary to carry out a big cleaning of the heating pipe. In order to save trouble, you can find a professional heating pipe cleaning company, or you can clean it yourself, close the heating inlet valve and outlet valve, find the location of the filter screen, the filter screen is generally between the heating meter and the water inlet valve, there is a plug on the side, unscrew the plug, take out the filter screen for rinsing, clean it, install it back, and tighten the plug. After opening the valve, you can hear the obvious sound of running water, and the heating pipe can heat up again.

Summary. The heating on the first floor is hot, and the heating on the upper floor is not hot, most of the factors are caused by the blockage of the pipes, which affects the water flow and reduces the water pressure.

The heating on the first floor is hot, and the heating on the upper floor is not hot, most of the factors are caused by the blockage of the pipes, which affects the water flow and reduces the water pressure.

Another factor is that the heating company itself does not have enough water pressure and low flow, resulting in a low overall heat transfer rate.

Hope it can help you, thank you.

The first floor is not hot, and the upper floors are hot, how to make the first floor hot?

The first floor is not hot, and ducted air can be exhausted.

Or install a circulating pump in the middle of the pipeline, 100W can be.

Increasing the water pressure allows excess heat to flow into your home.

It's all exhausted, and the big drainage pipes are all very smooth, and the first floor just can't get hot, what should I do?

According to your description, retrofitting a circulating pump is the best option.

A pump can be done for one or two hundred dollars.