The heating on the 1st floor is not particularly hot, is there any good way to solve it?

If it's just that your own home is not hot, and there is no problem with your neighbor's house, you can ask a plumber to repair it. Generally, the heating is not hot, the pressure is insufficient, the circulation is slow and needs to be repaired, there is an air blockage in the heating, the gas needs to be deflated, the heating filter is blocked, some radiators are not hot, the hot ones are turned off, and the non-hot ones can be heated up, which is called the hydraulic imbalance of the indoor circulation system.

In this case, the room system can be adjusted to turn off the hot heating first and let the non-hot heating heat up.

<> if the whole unit is not hot, it is necessary to see if the valve of the building is opened, and at the same time report to the property to deal with the gas in the pipe with the air release valve on the water separator, and release the air until the hot water is released. For example, if your home is a six-way water separator, first turn off the five-way (can only be operated all the way), open the return water exhaust valve, discharge one of the water, go to the heating hall (payment hall) to repair**, dial maintenance**, there is a master to repair, if you need to put the water in the "block" under the heating, they have a special water pipe, you can discharge the water from the radiator such as the bedroom into the bathroom.

There is dirt blockage that causes no heat or air that is not discharged, resulting in poor water circulation and no heat. In this case, exhaust first, flush the dirt in the drain, and then heat it up. The radiators and pipes at home are not hot, this situation may be that the main valve of the heating is closed, the main valve is generally in the inspection well of the unit staircase, we only need to check the supply and return valves, and confirm that it is opened.

In the early days of heating, the water of the heating system contains a lot of air, so the valve must not be opened, otherwise half of the water and half of the air will be poured into the radiator, so that the radiator will continue if it is not hot, so the size of the inlet valve must be appropriate. If it is the responsibility of the heating unit, the heating unit has to bear the maintenance, and if the maintenance is not good, you can keep evidence, refuse to pay the heating fee, and you can also ask the responsible unit to compensate for the resulting losses through judicial channels.

If it is caused by insufficient floor heating pressure, you contact the property or heating company, if it is not hot because of the accumulation of gas in the floor heating pipe, open the floor heating vent valve to let the gas in the pipe discharge, if it is caused by the filter blockage in the floor heating pipe, you need to remove the filter screen and clean it

The heating on the first floor is not particularly hot, and some electric heaters can be purchased. You can also buy an electric mattress in the bedroom to keep warm.

Some new communities or new heating, due to the new heating, water circulation may not be very good, therefore, the new heating may not be very hot at first, in this case, you can not rush to open the heating valve, let the heating flow circulate for a few days, and then turn on the use, and then turn on the heating after the heating is stable, in this time you can also check the situation of the radiator, if there is a fault, you can call the heating company for after-sales treatment.

Summary. In today's heating pipes, each household is connected in parallel for heating, but the radiators in the home are connected in series. The floor heating on the first floor is not hot, and the upstairs is hot, so there must be a problem with the floor heating in your home.

One is that the heating valve in your home is not opened, and the goods are not opened enough. The second is that each household in the corridor has a valve and a filter screen, it may be that the filter screen is pasted by rust and impurities, because the heating water is recycled, there are rust removers in the enterprise, and there are more impurities. If so, remove the filter and clean it.

Separate household heating, the first floor is not hot, and the upper floors are hot, what to do.

In today's heating pipes, each household is connected in parallel for heating, but the radiators in the home are connected in series. The floor heating on the first floor is not hot, and the upstairs is hot, so there must be a problem with the floor heating in your home. One is that the heating valve in your home is not opened, and the goods are not opened enough.

The second is that each household in the corridor has a valve and a filter screen, it may be that the filter screen is pasted by rust and impurities, because the heating water is recycled, there are rust removers in the enterprise, and there are more impurities. If so, remove the filter and clean it.

It's not hot on the first floor, it's not a household.

If this is the case, it means that there is a problem with the design of the heating line of the building, and a special maintenance person is found to repair it, and the wiring is re-routed and set up the pipes.

It has been hot for more than ten days so far, and today it is not hot for 3 households on the same floor.

That could be that he didn't burn enough today.

It's all hot upstairs. In this case, he should be heating from the top down, but you have to see if this is not the case tomorrow, if it is only for one day, it will be fine.

The heating inlet and return risers are hot, and the row pipes on the first floor are not hot.

If this is the case, it means that there is a problem with the design of the heating line of the building, and a special maintenance person is found to repair it, and the wiring is re-routed and set up the pipes.

Some of the owners of the family live on the first floor, the key is to say that the comparison is cost-effective, and the transportation is also very convenient, no need to leave and right indoor stairs. But in winter, some first-floor owners will feel that the heating on the first floor is very sloppy. Why is the heating on the first floor poor?

What should I do if the heating on the first floor is not hot? There are many reasons why the heating is not hot, and here Jinjin will bring you the reasons and solutions for the heating not to be hot.

Why is the heating on the first floor poor?

1. Heating system reasons.

Residents on the top floor close the cut-off door completely or partially, causing the circuit to be blocked or interrupted. Another factor is the blockage of the heating system, some heating systems that have been in operation for many years but have not received the necessary maintenance and maintenance, such as blockage, leakage and other phenomena affect the heating effect of the whole system. There are also some residential areas where the original design of heat supply and heating area do not match, forming a "small horse-drawn cart", and the above problems should be solved by the property management department.

2. The heating is due to itself.

Now most residents use the old-fashioned cast iron heating, most of this heating is old, it is necessary to rely on the heating cover to dress up, the decorative effect is improved, the quality of life is reduced, "beautiful and frozen people", some residents simply open the heating cover in winter, despite this, the heat dissipation effect is still greatly reduced, if you want to heat up fundamentally, the best way is to use the new type of heating without cover.

3. The heating has the sound of water.

The main focus is on the top-in and bottom-out installation method, because there is gas inside the radiator that cannot be discharged. The solution is to close the water supply valve of the radiator, open the discharge valve, discharge the gas inside the radiator, close the exhaust valve, and open the water supply valve. If it cannot be ruled out, check whether the flow rate of the system is too low or the gas content of the circulating water of the system is too large.

How to solve the problem that the heating on the first floor is not hot?

1. Check whether there is any nest gas, water leakage, and the heating valve is not opened, and then solve it according to the specific situation.

2. If the heating below the top floor of the community is hot, you can ask the residents whether it is getting cooler and cooler from the first floor, if so, it means that the hot water for the district heating is from the first floor to the top layer up, that is, there is a problem with the design of the HVAC pipeline of the building, and you can contact the heating company to solve it.

1. If the heating below the top floor of the unit is hot, you can inquire whether it is getting cooler and cooler from the first floor to the top, if so, it means that the hot water heated by the unit where the home is located is from the first floor to the top layer up, that is, there is a problem with the design of the HVAC pipeline of the building. 2. The heating flow pipe should be exhausted, and the exhaust valve is generally installed everywhere, if the displacement of the exhaust valve is too small or broken, the air of the pipeline can not be removed in time, so that the expansion of the pipeline, so that the water can not flow or circulate. If there is no problem with the exhaust valve inspection, then check whether the pressure of the boiler and the power of the circulating water pump are up to standard.

You can find a professional to install a circulating pump to enhance thermal circulation, but if that doesn't work, you need to consider equipment such as indoor air conditioners.

If the radiator is hot, but the indoor temperature is relatively low, then you can see if the number of radiators installed is too small. If the radiator is not hot, then you can check if there is something wrong with the radiator and plumbing. Rubens Heating hopes to help you.

After the heating started, the public also encountered a lot of problems in use.

Some people complained that they opened the valve to release water, but all that came out was cold water, and the heating did not have any temperature.

Another person reflected: "The neighbors on the left and right are hot, but only their own homes are not hot." ”

There are a lot of problems like this, so how to solve these problems in heating?

Don't worry, for everyone, you can follow these methods to check yourself first!

The neighbors on the left and right are hot, but only their own house is not hot.

After the heating was turned on at home, it was still not hot, I thought it was a problem as a whole, so I went to the neighbor's house to feel it, but I didn't expect the neighbors to be very warm, but my house is the same as an ice cellar. A citizen is very puzzled, what is going on?

In this kind of situation, where the neighbors are hot and only one is not hot, you can first check whether it is caused by the mixed installation of floor heating and hanging heating. If your neighbors have floor heating and your family uses hanging heating, this kind of situation is likely to occur, so it is recommended that the new community unify the heating form before installing heating equipment.

The other floors are hot, but this floor of my house is not hot.

Why are the 12th and 14th floors very heated, but the 13th floor is not hot? Is there a problem with the heating?

If the overall heating of the building is normal, and all other floors are hot, only the floor of your home is not hot, it should be considered that it is the problem of the courtyard pipe network on the floor. It is recommended to check whether the heating pipe network on the floor is operating normally, and the owners of the directly managed community can seek help from the heating company, and the owners of the non-directly managed community can notify the property.

At the same time, attention should be paid to cleaning the filter screen at the valve of the thermal pipe network connecting the residential pipe network to the residents' household pipe network in time to see if the filter is blocked.