The electric car has electricity, but it doesn t go, why?

1. In such a situation, the regulator is damaged and needs to be pushed to the nearest repair shop for repair;

2. The function of the regulator is to adjust the circuit of the whole vehicle, if there is no regulator, the electric vehicle cannot operate normally;

3. Most of the adjusters will be fixed under the back seat.

There are many possibilities for an electric car to not move after it is energized. One is the circuit problem, that is, the line to the motor is broken in the middle. Although the battery has electricity, the motor has no power, so it will not move.

A broken control brake line can also cause the motor to lock up, and the effect of controlling the brake line to break can be the same as that of a brake. You can open the circuit and check it. There are a lot of connectors inside that are bayonet.

Try to plug it in tightly. The wires that connect the motor are easy to find. It is the thickest.

It's also possible that your car was repaired, the line was not lined up well, the skin was worn out during the turn, and then the wire was burned out by the discharge.

1.The battery output is not normal.

The battery output of the electric vehicle is abnormal, such as if the battery output is too low, it will lead to battery failure, and then the phenomenon that the electric vehicle does not run away when it has power.

Solution: Replace the battery.

2.Brake bar problems.

Because the brake lever has a power-off brake, which is commonly known as a brake power-off, if the brake does not return, it will cause the electric vehicle to be energized and not go away.

Solution: Replace the brake lever.

3.The controller is damaged.

If the controller of the electric vehicle is damaged, the electric vehicle will not rotate even if there is electricity.

Solution: Smell the controller for burnt smell, if the controller is really damaged, you need to replace it with a new one.

4.Motor failure.

If the motor of the electric vehicle fails, such as the improper contact of the carbon brush of the motor, it will also cause the electric vehicle to not go when it has power, and the damage to the motor hall will also cause the power to not go.

Solution: Repair the motor or replace it with a new one.

5.The problem of the turnaround.

If there is a problem with the handlebar of the electric vehicle, such as using a short wire to turn the positive pole and the signal line, if the car rotates, it proves that the handlebar is broken, and the handle is broken, which will also cause the electric car to not be able to go even if it has electricity.

Solution: Replace or repair the turner.

The electric car has electricity, but if you don't leave, consider whether the power supply is disconnected.

The air switch tripped, the power signal system failed, the brake power loss problem, the controller problem, the fuse problem.

1. The air switch tripped.

If an electric car, whether two-wheeled or three-wheeled, once it doesn't move halfway, the first one should check the air switch. The air switch is easy to trip, if it does, just push it up.

2. Power signal system failure.

The main thing is the fault of the burglar alarm. Nowadays, in order to pursue intelligence and high-end, many electric vehicles are equipped with burglar alarms and keyless driving functions. If there are too many things, it is easy to have problems.

There are too many functions, which can easily lead to complex lines and poor contact. If the electric door lock is damaged and the signal line of the controller electric door lock is not in good contact, turn on the keyless driving function of the anti-theft device, and you can do it.

3. Brake power failure.

If the brake switch is stuck or malfunctioning, it will cause the whole vehicle to have electricity and can't go, we can try to brake the car a few times.

4. Controller problems.

The "Flying Car" function on the controller is to adjust the output of the controller by means of an electric door lock. You can directly short the two wires of the controller, the power cable (thick red wire) and the power signal cable (thin red wire).

5. Fuse problems.

If the fuse blind wire is in poor contact with the two-wire stamping parts, or the whole vehicle has a short circuit problem, it will cause the fuse to blow out. The battery compartment can be removed, and the lid of the compartment can be opened to check whether the fuse is disconnected or short-circuited. If so, you can try shorting it.

1. There is a problem with the battery connection cable or battery plug. A cable on the battery is loose, or the terminal of a battery is corroded and loose. The connecting wire will sometimes be rubbed by other things, etc., resulting in internal injuries to the power cord, which will cause the same consequences as the corrosion and loosening of the wiring head, the current is not forceful, it can turn when there is no load, but it will not work after the load, but the lights, horns, etc. can work normally.

If these problems occur, try pulling the wires or plugs by hand and fixing them one by one.

2. The air is turned on and tripped. Once the electric car does not move in the middle of the road, the first thing should be to check the air switch.

The air switch is easy to trip, if it does, just push it up. There are two reasons for a switch tripping: a trip with a violent vibration, or a trip with an instantaneous current that is too large.

3. Power signal system failure. Some two-wheeled electric vehicles and leisure three-wheeled electric vehicles on the market, in order to take the high-end route, are basically equipped with burglar alarms, and they all have the function of keyless driving. But with more functions, it's easy to have problems.

4. Poor contact of the power supply line of the controller. Find the controller of the electric vehicle, mainly check the red and black thick lines of the controller to see if the two wires are loose and fall off, if there is, then install it. If it is installed, it cannot be solved, then there is a problem with the motor, and the general motor carbon brush contact is not real, which will also cause the power to not go, which needs to go to a special repair shop.

5. Brake power failure. The signal source of brake power failure is formed after collecting the action of the brake switch, if the brake switch is stuck or malfunctioning, it will cause the vehicle to have electricity and can not go, you can try to brake the car several times.

There are several possibilities:

1. The battery may be damaged.

Second, the tire pressure is insufficient.

3. The brakes are too tight.

In general, first look at whether the brake handle is back in place, if the brake handle is disconnected, the brake handle can be driven by hand, in addition to the above situation, turn it, the controller is damaged, the motor is damaged, and the Hall is damaged will appear a little bit of a phenomenon that does not go.

In this case, there is a possibility that the power supply will be broken, so be sure to find a professional to check and repair it for you.

It is some special circumstances: the car is boring, sometimes it walks, sometimes it does not go, the power consumption increases, and the mileage of the car is short.

2.Check the brake handle to see if it is stuck, and there is a power-off protection switch in the brake handle. Try a few more brakes.

3.There is no problem with the above, then you have to go to the maintenance inspection to see if it is a controller or a motor or a circuit problem.

Pure hand-typed, if it helps you, give me a thumbs up, thank you!

Hello friend, according to the question you provide for you to answer, do you have electricity in this green source electric car? Let's go, take a look, does your display display show a p font size? If there is a p, you pinch the handbrake and turn it on again.

This is all caused by this handbrake pulling up.

Questioning hand kills and pinching the P word can't be eliminated.,Occasionally you can only run 16 yards.,Once you stop the P word, you can't eliminate it.。

Answer: You have a problem with this controller, and you need to drive the vehicle to this place to repair the battery car to check it, your controller. Or this handbrake, this switch has a problem.

Ask if there is a problem with the P switch.

Question: Where to buy the P gear switch, can you provide a contact method?

The question of the maintenance site can not be solved at two points, you send the manufacturer **.

The question P word can't be eliminated.

Hello friend, according to the question you provide for you to answer, do you have electricity in this green source electric car? Let's go, take a look, does your display display show a p font size? If there is a p, you pinch the handbrake and turn it on again.

The P word can't be eliminated.

Hello friend, according to the question you provide for you to answer, do you have electricity in this green source electric car? Let's go, take a look, does your display display show a p font size? If there is a p, you pinch the handbrake and turn it on again.

The P word can't be eliminated.

Hello friend, according to the question you provide for you to answer, do you have electricity in this green source electric car? Let's go, take a look, does your display display show a p font size? If there is a p, you pinch the handbrake and turn it on again.

The P word can't be eliminated.

Hello friend, according to the question you provide for you to answer, do you have electricity in this green source electric car? Let's go, take a look, does your display display show a p font size? If there is a p, you pinch the handbrake and turn it on again.

The P word can't be eliminated.

Hello friend, according to the question you provide for you to answer, do you have electricity in this green source electric car? Let's go, take a look, does your display display show a p font size? If there is a p, you pinch the handbrake and turn it on again.

The P word can't be eliminated.

Hello friend, according to the question you provide for you to answer, do you have electricity in this green source electric car? Let's go, take a look, does your display display show a p font size? If there is a p, you pinch the handbrake and turn it on again.

Electric cars just don't go when they have electricity, for the simple reason that they don't spend a penny to fix them themselves.

Typically, there are several situations:

1. There may be a problem with the connecting wire on the battery;

2. The terminal of a certain battery is corroded and loose;

3. The connecting wire will sometimes be rubbed by other things, etc., resulting in internal injuries to the power cord, which will cause the same consequences as the corrosion and loosening of the terminal head;

4. The current is not forced;

5. A section of the electric belt Dan Zhaoyuan line failed, resulting in no power.

The best troubleshooting method is for electric vehicles to use if they have power:

1. Unplug the brake lever socket (normally open brake lever). If the motor is running, it is a brake failure and the brake handle should be replaced. The 5V voltage of the turn source is normal, check and test the signal voltage of the turn handle, and turn the turn handle, the signal voltage should change from low to high.

2. Check whether the battery output of the electric vehicle is normal, if the output is too low, it proves that the battery is bad and the battery needs to be replaced urgently.

3. Pull out the brake line, if the car rotates, it proves that the brake lever is broken, and the brake lever must be replaced.

4. Check the quality of the motor, and the unreal contact of the carbon brush of the motor will also cause the electricity to not go.

Summary. 1. First of all, check whether your brake handle has returned to its original position 2, use the multimeter voltage to measure the voltage of the main thick red line at the controller 3, and then find the controller of the electric vehicle Find the three thick motor wires Check whether the three wires have fallen 4, there is also a possibility that the brakes are locked and the brake line can be loosened 5, in fact, there is another point to check whether the line is connected to the virtual line Whether the line is loose.

The electric car has electricity, but it doesn't go, why?

Hello, glad to answer for you! The electric car has electricity, but it does not go for the following reasons:

Hello, there is electricity just suddenly not gone.

1. First of all, check whether your brake handle has returned to its original position 2, use the multimeter voltage to measure the main thick red line voltage at the Ant Travel Controller 3, and then find the controller of the electric vehicle Find the three thick motor lines Check whether the three lines have fallen 4, there is a possibility that the brakes are locked and the brake line can be loosened 5, in fact, there is another point to check whether the line is connected to the virtual line Whether the line is loose and early moving.

Five reasons you can rule out, check it out! <>

I just finished riding and then charged and didn't leave.

It should be that the line of the brakes is loosened.

My handbrake cable is long gone.

Oh brake line. Let me see.

Okay. Measure the voltage at the controller.

If all of the above is a problem, it is the loose connection of which wire! This happens for no reason.