How to clean up the debris in the Huaga, how to clean up the debris in it

1. Dry chisel: As the name suggests, it is to buckle little by little with a sharp tool, and the tool is a large one, a small two triangular pyramids. The spoils on the surface, the flesh is scraped with a blade, and the hole is drilled with a triangular tip. The advantage of this cleaning is that it is not afraid of oil yin, and it is not afraid of water cracking, but it is too laborious.

2. Washing: After soaking the King Kong directly in water for half a day, it can be easily cleaned up with a stiff brush or wire brush, and it can be dried in the shade after cleaning, and the degree is based on the surface to restore the color and luster immediately with a fine brush to oil and brush evenly, remember to brush it several times to brush evenly, and then use a paper towel with strong adsorption to dry the excess oil slick one by one, and you can seal it in a plastic bag. There are several benefits to cleaning up this way:

1) Labor-saving. Clean and thorough. 2) After the blister, you can directly observe the color of the seed, the seed is red when it sinks into the water, and the seed is left with high density and good seeds, and the seed floats and the color is basically unchanged for the bran seed, and the density is not enough to eliminate and the crack of the diamond itself will also be closed, and it will not crack after sealing.

3. In May, the warm and humid airflow in the air continues to increase, and then take it out to play in the summer, and it is basically finalized, which can basically solve the problem of cracks (the effect of large cracking is not good). The disadvantage is that it is difficult to grasp the heat and it is easy to cause cracking.

Do not put salt, put a few drops of sesame oil in water or put.

2. 3 slices of ginger.

You can pick it up by hand or with a small spatula.

You can choose one of oxalic acid and acetone, both of which are stone-cleaned.

High-pressure water gun flushing in a car wash.

It's hard to get rid of unused household clutter!

Buy the corresponding storage box, label it and sort it out and store it, and throw away the things you don't use. or put it in the pantry.

Large black garbage bag. Pack it all in. The next step is to put it in the trash. Finish.

Use storage bags to sort them out.

There's always a little dust in your keyboard, and this little vacuum cleaner will keep your keyboard as clean as new

Here's how to clean up the clutter on your keyboard:

The first step of cleaning is to turn the keyboard upside down and tap the bottom surface of the keyboard to clean out some dust, hair, etc. accumulated inside the keyboard.

Step 2: Clean the surface of the keyboard: Use a brush to clean the surface of the keys to roughly clean up the accumulated sweat and dust.

Finally, use a soft cloth or cotton swab dipped in some detergent to carefully clean the sides of the keys and some stubborn stains, and be careful not to use too much detergent when doing this step, so as not to flow into the inside of the keyboard. In addition, it is not recommended to use anhydrous alcohol, because anhydrous alcohol may have a certain corrosive effect on the surface of the keyword.

1.Tap the keyboard. Turn off the computer and remove the keyboard from the console.

Place a newspaper on the table, flip the keyboard down, about 10 cm from the tabletop, and slap and shake. You'll find a lot of "stock" falling out of the keyboard: in addition to dust, there are cookie crumbs, coffee grounds, erasers, strands of hair, etc.

2.Blow off the clutter. Use a hair dryer to blow through the gaps in the keyboard keys to blow off the clutter attached to it, then flip the keyboard down again and shake it to beat.

3.Scrub the surface. Use a soft cloth dipped in diluted detergent (be careful not to get too wet) and scrub the surface of the keys.

Then use the vacuum cleaner's vacuum brush to suck the keyboard again to suck up the residue missed by the above program. 4.Disinfect.

After the keyboard is cleaned, you may wish to dip it in alcohol, disinfectant or medicinal hydrogen peroxide for disinfection, and finally wipe the surface of the keyboard with a dry cloth. 5.Wash thoroughly.

If you want to give your keyboard a complete cleaning, you'll have to remove the caps from each key. The keycaps of a normal keyboard are removable, you can pry them off with a small screwdriver or ear picker, and proceed one by one from the corner part of the keyboard area to the middle part, and the larger keycaps such as the space bar and enter key are more difficult to return to their original positions, so try not to disassemble them. To avoid forgetting where these keycaps are, it's a good idea to take a picture of the keyboard layout with your camera or draw a sketch first.

Once the keycaps are removed, they can be soaked in detergent or disinfectant solution and carefully scrubbed with a flannel cloth or disinfectant paper towel.

Related tools: special vacuum cleaner, high-pressure air spray can, cotton swab, manual air compressor 1. Use a special vacuum cleaner to clean the dust on the surface of the keyboard. 2. Use a cotton swab to clear the large gaps, and brush off the slightly sticky hairs and dust by the way.

If there is some dust sticking to the keyboard, you can also use the cleaning solution mentioned earlier to enhance the cleaning, just wipe it with a cotton swab. 3. Use a high-pressure air spray can or a manual air compressor to remove the dirt in the cracks of the keyboard.

It can be removed, that is, it will be seen at a glance that it is fake, mainly because the strength on the right side is not easy to get, and there is no reference, and I don't know what light and structure. There's no way to do anything else.

Removal is possible, and it certainly won't be too real to be made. If you are going to do a rendering of the decoration, I suggest drawing another one, which will be much simpler.

There's always a little dust in your keyboard, and this little vacuum cleaner will keep your keyboard as clean as new

The easy way to do this is to buy a wool brush.

If you have high requirements, you can buy a special keyboard vacuum cleaner.

Remove the button panel and clean it.

First, remove the washing machine drain and place it on an empty bucket (at a certain height) and close the inlet valve and front door.

Second, pour the water from 3 kettles with descaler (commercially available) into an empty container, prepare the descaler in the ratio of water l 2 and stir well.

Third, open the "detergent addition box" and pour the mixed descaler solution from the detergent addition box, taking care not to splash on the **.

Fourth, press the power switch of the washing machine, set the program to "Washing Program" (the longest time selection), and make the washing drum rotate; After the descaling solution is discharged from the drain pipe into the barrel, the discharged descaling liquid is added from the detergent addition box, and so on many times until the program is finished, and the filter is opened to clean the filter.

Fifth, after the machine is finished, open the inlet valve and restore the drain pipe to its original position. Re-select the washing program to make the washing machine run again, and when the program is finished, clean the filter again. At this point, the descaling and cleaning are complete.

After the descaling is completed, the surface of the washing machine drum may be slightly dark black due to the action of the descaling liquid, but it will not affect the normal use, and the clothes can be restored to their original state after washing the clothes several times.

There's always a little dust in your keyboard, and this little vacuum cleaner will keep your keyboard as clean as new