When decorating a new house, why can t you use tile adhesive for the whole house?

Introduction: When decorating a new house, it is not recommended that everyone use tile adhesive, mainly because the style is relatively single, although the style and color of the tile are constantly improving, but most of them are mainly plain, so it does not look so good-looking, and the other is relatively high. It doesn't feel very cost-effective, and the whole house is tiled, which will not look so warm and even a little cold.

First, because the style of the tile is relatively simple, the later improvement is also more troublesome

Everyone wants to have their dream house, but when decorating, we are more distressed, what to pretend to be, in fact, I prefer that kind of simple style, there should be things that should not be there, and you can spend less money on less money, after all, the economic pressure is relatively large. We must pay attention when decorating, can not be the whole house with ceramic tiles to decorate, some people think this is more beautiful, but to know that all the tiles its style and style is not very much, spread on it will not look particularly good. <>

Second, the tiles are too high, and it is very cost-effective if the hand is not very generous

In addition, it is relatively high, because it is said that it is better than dozens of dollars for an ordinary tile, hundreds of thousands, and the whole house is quiet on the tile is really a lot of money, in addition, it also takes a long time to cause your house decoration time to be extended, you need to pay more, it is not cost-effective, you may be better if you have more money, but don't do such a thing if you don't have a lot of money. <>

Third, all tiled will make the whole house look cold

There is also a more important reason is that if all the tiles are paved, it will also lead to some cold in the house, which is not so warm, and you want to be warm in your home in winter, but after all the tiles are paved, it will give you a kind of cold from the inside out. When you are decorating, you can actually go to other people's homes to see how others decorate, and there is no need to put all the tiles on them.

Because all the tile adhesive will greatly reduce the quality of construction, for the environment of the whole house to make it weird, will not be more solid, and will occur hollowing, ** is also relatively high, the utilization rate is also very low, will cause waste.

It is because if you choose to use tile adhesive, if it rains, or there is some moisture in the bath, it may cause it to fall off, and it will be more expensive to decorate.

The cost of this is very high, and the smell in the house is not particularly good, so it cannot be used in the whole house.

1. Do you need tile adhesive for decoration?

2. What are the advantages and disadvantages of tile adhesive?

The advantage of tile adhesive is that it has very good water retention, and it is not easy to produce hollow drums after use, and the adhesive strength is very high, it is not easy to fall off after pasting tiles, and the thickness of tile adhesive approval is less than that of traditional cement, so it saves a lot of space position, and it is very convenient when tile adhesive construction, and it is not necessary to soak bricks and wet walls in advance, and the disadvantage of tile adhesive is that it is much higher than cement mortar, but from the perspective of aesthetics and sticking effect, the high cost is also more reasonable. In addition, the disadvantage of tile adhesive is that the requirements for the base layer are relatively high.

I think tile adhesive should be used, because it can be better decorated, and it can make the effect of the tile better, and it can also make the tile look more beautiful.

No, because the tile adhesive sometimes falls off and can't stick to things, which can easily cost our money.

I don't think it's necessary, it's too wasteful to use tile glue for the whole house.

It is not necessary to need tile adhesive, the role of tile adhesive is to stick to the wall, so that the ceramic tile and porcelain tile are more firm. The following characteristics of tiles are recommended:

1. Relatively heavy tiles. Some tiles are larger in size, and the weight of a piece is very large, so it is recommended to use tile adhesive for safety. For example: Calacatta, microcrystalline porcelain panel paintings and other series.

2. Top. It is recommended to use tile adhesive for the tiles on the top of the head and the tiles over the meter, in case it falls off, it will not be fun.

3. Splines and corners (male angles). For example, there is a corner of the place, there is a grade of decoration to choose the gourd with tiles, the edge, etc., this place should be firm, otherwise the child will shake it loose.

I'm Lei Feng, no thanks!

Cement: one of the materials commonly used in our decoration and construction, **cheap, used for building walls, tiles and other places. However, the disadvantages of large paving thickness, unfirm pasting, many materials used and easy hollowing make the status of cement begin to decline.

Tile adhesive: a new brick-laying auxiliary material, its main characteristics are high bonding strength, water resistance, relatively thin pasting, space-saving, and more convenient construction. The cost is higher than that of cement.

So, wall tiles: tile glue or cement, which is stronger? We mainly compare from three aspects: materials, construction, and aesthetics.

1. Material comparison.

Comparison of cement and tile adhesive powder.

Powder comparison: cement and tile adhesive are similar in shape and color, tile adhesive is slightly coarse, and there is no pungent odor.

Comparison of cement and tile adhesive paste.

Slurry comparison: tile adhesive and cement are proportioned separately, water is added, stirred into slurry, tile glue is smooth creamy, high viscosity, and flows slowly; The cement slurry has agglomerates and particulate matter, which breaks off quickly.

2. Comparison of construction effects.

Comparison of cement and tile adhesive construction effects.

Cement slurry construction: the traditional cement river sand bricks, the construction steps are complex with wet walls, soaked bricks, support and other steps, not only the efficiency of the construction is relatively low, the effect of the knot is not good, and it is easy to appear after a short time The tile is hollow and falls off.

Comparison of cement and tile adhesive construction effects.

Tile adhesive construction: You can omit the steps of wet wall, soaking bricks, etc., and because it is full of slurry, there will be no hollowing, falling off, and the tiles pasted out are of course more beautiful and stronger.

Comparison of pasting effects.

Comparison of pasting effect: turning over the paved wall tiles, the cement paving is uneven, and there are pores on the surface, which is easy to cause the tiles to be pasted firmly, hollow and fall off; The tile adhesive is evenly distributed, the filling rate is high, and it is not easy to produce hollowing and falling off.

Robustness contrast.

The cement slurry paving tile is broken and falling off, because the tile is separated from the water when it encounters vibration, and the tile and cement are very hard and cannot be detailed about the impact force of the differentiated impact drill;

The tile adhesive has made 6 holes in a row, and the tile is still very stable, because the tile adhesive has good flexibility, and the tile adhesive is closely combined with the ceramic tile, which effectively absorbs and differentiates the impact force.

Robustness contrast.

3. Aesthetics.

The formula of tile adhesive is more reasonable, the ratio is uniform, and the shrinkage in the bonding process is more consistent, so the surface of the tile will be relatively flat, and because it is full of slurry, there will be no hollowing, falling off, and the tiles posted are of course more beautiful and stronger.

In home renovation, if you are not sure whether to choose tile adhesive or cement, then take a long look at your budget. Although the cement has a high probability of hollowing and falling off, the cost of cement is lower than that of tile adhesive, and if the decoration budget is insufficient, then use cement to pave.

Floor solid tile binder, also known as face tile binder, is made of cement, quartz sand, polymer cementing material with a variety of additives through mechanical mixing. Tile adhesive is mainly used as an adhesive for bonding tiles and face tiles, also known as polymer tile bonding mortar. [1] This tile adhesive completely solves the problem that there is no high-quality special adhesive material to choose from in the pasting construction of ceramic tiles, floor tiles and other materials, and provides a new and reliable ceramic tile special adhesive product for the Chinese market.

Product features 1. High bonding strength and fast hardening speed, which can greatly improve the service life and decorative effect of various paving materials. 2. The construction is convenient, and it can be used only by processing an appropriate amount of water and stirring. The tiles to be pasted do not need blisters, and can be pasted directly.

3. Excellent compressive and tensile strength, water resistance, alkali resistance and weather resistance, not affected by the environment. 4. Good workability, good water retention, workability and flow resistance. During the bonding process, the tile can be adjusted for 10 minutes and operated for 60 minutes.

5. The ultra-thin layer construction can be realized, and the coating thickness is less than half of the traditional process, which saves costs and reduces the shrinkage rate, and will not cause the cracking and falling off of the decorative adhesive surface due to force. 6. Non-toxic, tasteless, non-polluting, it is a real green and environmentally friendly product.

Tile adhesive, also known as ceramic tile adhesive, is mainly used for pasting decorative materials such as tiles, face tiles, floor tiles, etc., and is widely used in interior and exterior walls, grounds, bathrooms, kitchens and other building finishing decoration places. Its main characteristics are high bonding strength, water resistance, freeze-thaw resistance, good aging resistance and convenient construction, which is a very ideal bonding material. Tile adhesive, also known as tile adhesive or binder, adhesive and other names, is a new type of material for modern decoration, replacing the traditional cement yellow sand, the adhesive force is several times that of cement mortar, can effectively paste large ceramic tiles and stones, and avoid the risk of falling bricks.

Good flexibility to prevent hollowing in the production of drums. This product is a polymer modified cement-based tile adhesive, which is divided into No. 1 (ordinary type (reinforced) and No. 3 (larger size tile or marble) and other varieties. No. 1 tile adhesive:

It is suitable for pasting all kinds of floor bricks or small bricks on the wall surface of ordinary mortar surface;

No. 2 tile adhesive: It has strong adhesion and anti-falling performance, and is suitable for the pasting of wall tiles and non-mortar surfaces such as wood plank surfaces or old finishes with large adhesion requirements; No. 3 tile adhesive: large adhesion, more flexible, can resist the stress caused by thermal expansion and contraction of the adhesive layer, suitable for pasting ceramic tiles on gypsum board, fiberboard, plywood or old finishes (tiles, mosaics, terrazzo), etc., as well as the pasting of various stone slabs of larger sizes.

In addition to gray, tile adhesives are also available with a white appearance, suitable for light or translucent marble, ceramic tiles and other natural stones. Tile adhesive contains a variety of additives, specifically the functionality of tile adhesive. Generally, tile adhesive is added to provide water retention and thickening of cellulose ether, as well as to provide latex powder that increases the adhesion of tile adhesive, the most common latex powder is vinyl acetate copolymer, laurate, ethylene vinyl chloride copolymer, acrylic acid and other additives, the addition of latex powder can greatly increase the flexibility of tile adhesive and improve the role of stress, increase flexibility.

In addition, other additives are added to tile adhesives with special functional requirements, such as adding wood fiber to improve the cracking resistance of the mortar and improving the opening time, adding modified starch ether to provide anti-slip performance of the mortar, adding early strength agent to make the tile adhesive improve the strength faster, adding water repellent agent to reduce water absorption rate and provide waterproofing effect. According to the powder: water = proportion.

Stir evenly to construct it; Within the allowable time of operation, the position of the tile can be adjusted, and the adhesive is completely dry (caulking can be carried out after about 24 hours, and heavy load on the tile surface should be avoided within 24 hours of construction).

The lower the water absorption, the higher the internal stability of the tile, and the more suitable it is for spaces with high moisture or moisture content (such as bathrooms and kitchens), and will not cause problems such as dark spots. Scratch on the ground, the poor tile due to the density relationship, completely like a piece of chalk, scratched everywhere there are imprintsIn addition to the color you like, you should also choose carefully:

First of all, take out any four tiles from the packing box and put them on a flat ground to compare whether the four bricks are flat and consistent, and whether the diagonal places of the tiles are embedded. Then you tap the surface of the tile with the palm of your hand and listen to the sound: the sound of a good tile is relatively low:

And the sound of the bad tiles is bright and has a noticeable reverberation. Of course, judging good or bad in terms of sound is relative. But a method of comparison can not be underestimated, the big difference between domestic and imported bricks is mainly in the consistency of the specifications of ceramic tile products.

Tile adhesive construction process: using tile adhesive to pave tiles, you can use the traditional dot sticking method, that is, the stirred mortar is applied to the back of the tile, and then it is pasted on the substrate. However, this sticking method is easy to cause hollowing, so we strongly recommend using the scraper method, the specific method is as follows:

The glue is applied to the working surface with a toothed scraper to evenly distribute and form a toothed pattern. Each coating is about 1 square meter (depending on the weather temperature), and then the tile can be kneaded on the top during the drying time; The selection of tooth scraper size should consider the flatness of the working surface and the degree of concave and convex on the back of the tile; If the gap on the back of the tile is deep or the stone and tile are large and heavy, double-sided gluing should be carried out, that is, glue should be applied on the working surface and the back of the tile at the same time.