Is it better to use tile glue or cement for tiling?

1. What is cement mortar? What is Tile Adhesive?

1. Cement mortar.

Cement mortar is a traditional construction scheme, but cement mortar construction, it is difficult to ensure that the cement mortar can be evenly covered, in addition to pay attention to the selection of cement number, cement mortar ratio and other precautions, there may be hollowing, falling off in the later stage; In addition, cement mortar construction is longer than the use of tile adhesive, and there are strict requirements for the level of construction workers.

2. Tile adhesive.

The new type of tile paste material has the advantages of simple construction and firmer paste, however, tile adhesive also has certain disadvantages, compared with cement mortar, the construction needs to ensure the flatness of the wall, and the base layer should also be cleaned, otherwise it will affect the bonding effect of tile adhesive.

Second, is it better to use cement or tile glue for tiles?

1. Comparison from the construction aspect.

If the cement mortar is used to paste the bricks, the construction steps have wet walls, brick throwing, support, etc., the effect is low, and the effect will not be too good, and it is easy to produce the situation of tile hollowing and falling off; If you use tile glue to paste tiles, tiles do not need to be soaked in water in advance, nor do you need to wet the wall, the technical requirements of decoration workers are not high, the paste speed is 4-6 times that of cement, the brick joints will not have excess slurry, the brick surface is not dirty, and you can also pave multiple tiles at the same time, which is much better than the paving method of cement mortar to be single-piece sizing.

2. Comparison in terms of aesthetics.

When using tile glue to paste tiles, the glue ratio of the wall is uniform, and the shrinkage during the bonding process is also consistent, so the flatness of the tile surface is high.

3. Start from the decoration materials.

At present, the quality of the ceramic tiles used in tiling is high, and the water absorption rate of ceramic tiles is also decreasing, so that if the traditional cement mortar is not improved in quality, the demand for tile adhesive will be higher, of course, the decoration market is also full of cement and tile adhesive of different quality, and the owners should pay attention to the method when they go to buy.

When I was decorating my home, I also asked the master this question, and the master recommended tile adhesive.

It is said that the construction efficiency with tile adhesive is fast, the brick laying is faster, and the bonding strength is high, and the tile is not easy to fall. Later, our home was Keshun home waterproof C301 tile adhesive, so long there has been no hollowing.

The phenomenon of dropping.

Tile glue is good for tiling. The cement needs to be blended, and the wall needs to be wet and supported, which will be more complicated; The tile adhesive only needs to be stirred with water, and the adsorption is good and the paving is fast.

Benefits of using tile adhesive:

1. When using tile adhesive, a large process can be omitted, and the stability is stronger after bonding with tile adhesive.

2. Compared with cement, tile adhesive is more scientific, and the adhesive is more firm.

3. It only takes 1-2mm to paste ceramic tiles, and the thickness of cement tiles is more than 10 times that of tile adhesive, so the use of ceramic tiles not only provides more space, but also saves materials.

4. The technical requirements for tiles with tile adhesive are not high, and the speed is 4-6 times faster than that of cement, so the owner can rest assured that the workers can construct without strict supervision.

5. When the wall is tiled, the tile adhesive will not fall no matter where it is pasted, and several tiles can be pasted together at the same time, while the cement is not good, and it must be pasted in a single piece.

The process to be used in the construction of ceramic tiles:

1. The construction sequence of ceramic tiles is base treatment, elastic line, pre-paving, paving, hooking, and cleaning. Grassroots treatment is to clean up the ground garbage, and deal with hollowing, cracking, sanding, etc.

2. The elastic line is to control the balance and height of the tiles, the wall is to pop up the standard height around the wall, and the ground is to pop up the cross line to separate the size of the floor tiles.

3. Pre-paving: Before pre-paving, you need to design with drawings, select the color, texture, etc., and then pre-pave according to the design drawings until you achieve the desired effect, and then implement ceramic tile construction.

4. Paving: When paving, the ratio of cement or tile adhesive to water is 1:3 blending, the thickness of tile adhesive is 1-2mm, and the cement needs to be about 25mm.

5. Grouting: The grout step needs to be processed after 24 hours of tile paving, and the impurities in the tile joints should be cleaned up first.

6. Cleaning: After completing the above five steps, wait for the tiles to dry completely, and then you can clean the tiles.

Hello kiss, when sticking floor tiles, it is better to use tile adhesive than to use cement grout. Here are some of the reasons: Easy to apply:

When using tile adhesive construction, you only need to apply the glue on the ground, and then paste the bricks on it, and you don't need to mix and deploy it like cement slurry, and the operation is simpler, and you can save time and labor with you. Fast construction speed: When using tile adhesive for construction, due to the simple construction and faster construction speed, the ground paving work can be quickly completed.

Strong adhesion: tile adhesive has strong adhesion, which can firmly stick the bricks to the ground, and is water-resistant, durable, and not easy to appear hollowing, cracking and other phenomena. The construction effect is good:

After the construction of ceramic tile adhesive, the ground is smooth and beautiful, and there will be no uneven and unsightly situation that is common in cement slurry construction. In short, when sticking floor tiles, the use of tile adhesive is more common than the use of cement grout, and the use of more square limbs and the effect is more ideal. Of course, the specific choice should be decided according to the actual situation, such as the material of the ground, the area and other factors need to be taken into account.

If it is to pave indoor floor tiles, it is not recommended to use tile adhesive, it is recommended to use cement grout. The reason for this point of view is mainly based on the characteristics of the tile adhesive itself and the characteristics of the floor tile paving.

The use of cement paste tile method is more traditional, the application is more extensive, relatively speaking, the technology of this cement tile is relatively mature, can be used to build walls, floor tiles, etc., the cost is relatively low. The adhesion of cement tiles is also relatively high, it is by mixing with other materials to produce a certain adhesion force to fix the object, and the adhesion is also very high.

If a large amount of tile adhesive is used, it may lead to excessive indoor pollutant release, and the release is relatively slow, which may continue to pollute and outweigh the losses.

It is recommended to use tile adhesive for wall tiles

Cement wall tiles are more complicated to construct and require some steps such as wet walls, soaked bricks, and supports. Not only will the construction efficiency be very low, but the effect of sticking out is not very good (it is easy to appear hollow, falling off and other phenomena). Tile adhesive can directly omit complex steps, and it is more practical.

Now the quality of ceramic tiles is getting better and better, so even if it is a wall tile, the water absorption is not so high, so the water absorption principle of traditional cement mortar can not meet the current paving, and the tile is getting bigger and bigger, and the tile adhesive is easier to paste. Moreover, tile adhesive is not affected by climate and humidity, and cement mortar is likely to cause the tile to fall off due to thermal expansion and contraction.

Hello, I personally think that the cement is better, the cement is generally prefabricated by the factory, adding a large number of party additives, so that the rigidity of the cement has been improved. It is a new type of material with good tiling effect. Cement is cheaper, the effect is not so good, the cement ** is slightly higher, but the performance is good.

It is recommended to use cement mortar, no need to add glue in the normal temperature season of the project, and 108 glue should be added appropriately for winter construction, and the cement mortar can be pasted directly at home. The above refers to the façade paste, from the daily use, the family with a percussion drill drilling is particularly easy to cause tile hollowing, or the temperature difference between the inside and outside of the bathroom and the humidity difference caused by the hollow, if you feel unassured, you can add 108 glue. Because the water absorption rate of polished bricks is very low, and the water absorption rate of the wall is too high, the double-sided water absorption rate of cement mortar can not be consistent, so it is not possible to use cement mortar to paste polished bricks, and tile adhesive has good water retention.

Tile glue is good for tiling.

For home decoration, we generally use tiles to pave special places such as balconies, bathrooms, and kitchen lights, mainly because these places are places where water is often used. Tile adhesive has many functions, it not only has an anti-aging effect but also has a certain water resistance. It also has a very high viscosity, so it is very suitable for tiling.

Due to the increasing complexity of construction technology in the decoration process, ordinary cement mortar can no longer meet the requirements of tiling. Some homes will choose the size of the larger tile paving, this general force than the posture is larger, with cement as an adhesive is difficult to firmly paste, the choice of tile adhesive is better than cement mortar.

Advantages of tile adhesive

1. Strong adhesion.

Tile adhesive is made of selected high-quality cement and washed sand supplemented by a variety of polymer materials through scientific compatibility and specific process processing, and also effectively overcomes the problem of internal stress concentration, so there is no hidden danger of hollowing out bricks.

2. Easy to construct and transport.

Tile glue is ready to use with water, no other mixtures need to be added, and no cement mortar is added. During construction, the tiles do not need to be soaked in water in advance, and the wall does not need to be wet, which reduces the process and improves efficiency.

3. Good waterproofness.

Tile adhesive has good waterproof performance, so it is very suitable for tiles, compared with cement, the waterproof performance of tile adhesive should be relatively excellent. The waterproofness of tile adhesive is good, so it can also save us a lot of trouble when decorating.

4. More environmentally friendly.

Using tile adhesive to paste ceramic tiles, not only high efficiency, but also tile adhesive is also an environmentally friendly material, and the decoration of the current service Huai is also more popular to decorate with environmentally friendly materials, so it is more reassuring to use tile adhesive to paste tiles.