What should I do if Girard Perregaux is magnetized by contact with a magnetic object, resulting in m

Magnetic fields are everywhere, and it is impossible to prevent it, and Hublot watches, which have always been very accurate, suddenly have a time error, and the first thing to guess is whether the watch is magnetized. There are many steel materials in Hublot mechanical watches, such as large and small steel wheels, escape wheels, shaft tenons of gears, bearings, screws and hairsprings, so the watch is very susceptible to magnetization. Once the Hublot mechanical watch is magnetized, the first situation that will affect it is that the watch is not accurate, there is an error, and in the serious case, the watch stops.

Moreover, in the development of today's social life, more and more electronic products appear around us. Therefore, the magnetic field is present around us, and there is only a difference in the strength of the magnetic field. Various types of permanent magnets are also widely used in electrical appliances, typically speakers and motors, and both magnets and DC magnetic fields can magnetize "hard magnetic" materials such as steel.

There is also the magnetic buckle on the leather bag, and the watch and credit card are the most afraid of being stained with magnetism. Hublot mechanical watches are generally magnetized to go fast (serious will stop), if the hairspring is stuck together, then the Hublot watch will go faster, about 2 hours or so faster. Steel parts are most susceptible to magnetization, including escape wheels and pallet forks.

The simple way to tell is to use a sensitive point compass and lay it flat. Then the Hublot watch is quickly skimmed over the top of the compass at close range, and this action also requires changing the watch a few more directions, and then repeating. As long as the needle of the compass moves, it means that the watch has been magnetized.

The principle of the demagnetizer is that it can produce an alternating magnetic field, and if the watch is placed in this magnetic field, it will be demagnetized, and if it is a constant magnetic field, it will be magnetized. Demagnetizers can be bought or made by themselves, and generally professional watch stores have demagnetization services. Moreover, in your daily life, you must be careful not to place your watch near or near electrical appliances that generate magnetic fields (such as stereos, refrigerators, computers, etc.), or magnetic objects (such as magnets, mobile phones).

If your watch suddenly does not go, then it is likely that the table has no output signal due to the following reasons, and all other aspects of the inspection are normal, check the circuit board with a multimeter without output signal, most of the reasons are due to the damage of the quartz oscillator or the failure of the integrated circuit, if the replacement of the quartz oscillator is invalid, then the entire circuit board needs to be replacedGear train faults, most of them are dust or foreign matter between the gear teeth, so that the gear train teeth are stuck with each other. There are also some tables where there is too much or very little oil, and too much oil causes adhesion between the wheels, wheels and splints.

Too little oil makes the rotation of the wheel train too resistant, which will make the TAG Heuer electronic watch go badly. In case of these faults of the stepper motor and wheel train, they should be cleaned, removed from foreign matter, and refueled.

Coil breaking, due to oxidation or man-made reasons, so that the coil is damaged, can be checked by multimeter testing, and generally needs to be replaced. The meter battery is not charged or the capacity is insufficient, and a new battery needs to be replaced. However, the watch often finds that the battery is dead in a short period of time, which is generally caused by high power consumption or the low quality of the battery itself.

In this case, you should first find out the cause, troubleshoot, and then replace the battery with a new one. The contact is not good, most of them are dirt on the positive and negative electrode contact reeds, and the contact with the battery is poor. Poor contact can also occur when the signal output point on the board is in contact with the lead point of the coil tip.

These will cause the circuit not to be turned on, so that the watch does not go or does not go well, and it is found that the circuit is not open due to poor contact, first clean the contact surface sufficiently, and then reassemble it. The stepper motor can not rotate, and the rotor of the stepper motor is a permanent magnet, which often cannot rotate due to the adsorption of iron filings and the stator is stuck, causing the watch pointer to stop or stop when walking.

Hello, it is possible that the watch is magnetized or the power is insufficient. Once the magnetism on the watch is all of a sudden, it goes very fast, even 1-2 hours a day. When wearing mechanical watches, pay attention to keep away from magnetic fields, such as stereos, televisions, mobile phones and other electrical appliances.

Magnetization is a common phenomenon nowadays, and the solution is not difficult, just go to the watch for repair and demagnetization, or bring your own demagnetizer, it only takes 30 seconds to demagnetize the watch, and there is no impact on the performance of the watch.

The watch is magnetized, generally speaking, it goes fast, if the hairspring is stuck together, the watch will go faster.

If it is close to the maintenance center, it is recommended to send it to the maintenance center for demagnetization. The degaussing machine in professional maintenance is generally imported, the degaussing is more thorough, it only takes a few minutes, and the maintenance fee Xiaoshen is also cheaper than Qiaoqinjing in Shouzhou, so if there are conditions, it is better to send it to the maintenance center for degaussing.

If it is close to the maintenance center, it is recommended to send it to the maintenance center for demagnetization. The degaussing machine in professional maintenance is generally imported, the degaussing is more thorough, it only takes a few minutes, and the maintenance fee is relatively cheap, so if there are conditions, it is better to send it to the maintenance center for demagnetization.

Hello, the watch will cause the problem of inaccurate time after being magnetized, although the quartz watch will not be magnetized, but there will be a phenomenon of stopping in a strong magnetic field. Therefore, when using the watch in daily life, it must be kept away from the magnetic field, away from TV, radio, induction cooker, etc., which will be magnetized due to long-term contact.

Many friends may be very confused, how can you tell that the watch is magnetic? There are many reasons why the watch is inaccurate or does not go, and the magnetic field in our daily life is everywhere, in order to accurately judge whether the watch is magnetized, you can use a flexible compass, put the compass flat on the table, hold the watch and shake it back and forth above the compass, if the needle of the compass moves, it means that it is magnetized.

There are two ways to degauss:

Methods of degaussing.

First, it is a professional demagnetization of the watch shop.

Methods of degaussing.

2. If you are far away from the watch repair shop, you can also demagnetize yourself, the specific method is: find a piece of iron that is hollow in the middle and is not affected by magnetization, stand firmly on the table, and then the magnetism on the watch can be "sucked" by the iron block to restore the watch to normal. It is to use a magnetized iron can, the two ends are connected, and the magnetized love watch can be demagnetized by moving back and forth in the iron can for 5-6 minutes.

It is recommended that you can open the warranty coupon attached to the purchase of the watch, under normal circumstances, there will be a service address on the warranty copy, or find a regular watch service center for testing and maintenance of the address of the store, etc., if there is a professional after-sales maintenance center nearby.