How to deal with second hand flooring and can it be used again

Updated on home 2024-07-13
14 answers
  1. Anonymous users2024-02-12

    Second-hand solid wood flooring and second-hand solid wood parquet flooring can be reprocessed, as long as the thickness reaches 4mm. Whereas.

    Laminate flooring is not suitable for recycling. Mainly because laminate flooring is a high-fiber wood-based panel, the surface and substrate are broken and cannot be repaired.

    Second-hand wood flooring will more or less have the problem of wear and tear, so how to renovate second-hand solid wood flooring? This is not difficult to repair, use a sander to grind off the surface paint, and then wipe a layer of wood wax oil, so that not only can repair the wear and tear of the surface of the second-hand wood floor, but also is very environmentally friendly, and you can construct it yourself. The specific secondary processing methods are as follows:

    Polishing the surface of the floor with sandpaper, in which the sandpaper is large and small, the larger the sandpaper, the finer and smoother the sandpaper.

    Secondly, use medical cotton gauze, which is not easy to pile and has less lint, dip it in wood wax oil, and rub it vigorously on the second-hand wooden floor. Finally, the reprocessed wooden floor can be used normally after one to two days of drying, which is very environmentally friendly and convenient.

  2. Anonymous users2024-02-11

    Second-hand flooring is said to be less polluted is just a pretense, in order to attract people, as long as the second-hand flooring is installed, there will be a lot of problems, the gap of the board is not tight, it will turn out the dust from the gap, and you don't know what the original condition is? So I advise you not to buy second-hand flooring, in addition, when you buy new flooring, don't forget, do a good job of ventilation after installation, and the time should be regular, because cheap flooring has a high concentration of formaldehyde.

  3. Anonymous users2024-02-10

    Old flooring is a common material in home decoration, but long-term wear and tear and erosion over time have led to various problems with the floor and affected the beauty and comfort of the entire space. When the old floor is no longer beautiful, we need to treat it, here are a few different ways to deal with it:

    1.Refurbishment: Renovation refers to sanding, painting and other treatments on the old floor, so that the floor can restore the luster and aesthetics of the original photo.

    This treatment is relatively time-consuming and costly, but it gives new life to old floors and makes the space look more comfortable and vibrant.

    2.Replacement: If there are problems that cannot be solved by renovation, such as deformation of the floor, serious damage to the floor, etc., we can consider replacing the old floor.

    The new flooring can be purchased according to the design and decoration style of the interior, making the space more harmonious and unified. In addition, the new flooring is safer and more environmentally friendly.

    3.Rug: If you can't decide whether you need to renovate or replace your floor, consider using carpet to cover the entire floor, which is simple and inexpensive, but requires regular cleaning.

    4.Do it yourself: If you love DIY or save money, you can try handcrafting or repainting your old flooring before installing it back. This approach requires some DIY skills, but can add a unique and personal element to a space.

    Whichever treatment you choose, remember that timely maintenance and repair of your flooring will prolong its life and increase the overall value of your home.

  4. Anonymous users2024-02-09

    When buying a second-hand house, you sometimes face the problem of old wooden floors. If the floor is in good condition, it does not require any treatment. However, if the floor is damaged or needs to be renewed, there are several ways to consider this bush:

    1.Replace the floor.

    If the floor is badly damaged, you can consider replacing the floor. This is usually done by a professional carpenter, who will remove the floor and replace it with a new one. This may take some time and cost, but it can add value to your home and make your home more aesthetically pleasing.

    2.Sanding and repainting.

    If the appearance of the floor is worn or in need of updating, sanding and repainting can be considered. This work may take some time and cost, but it can breathe new life into your floor and enhance its waterproofing and damage resistance.

    3.Cover with thin wooden floors.

    If you don't want to spend too much money and time on the floor, you can consider covering it with thin wood floors. This method is also known as a "floating floor" because it does not need to be nailed or glued to the ground. Thin wood flooring is easy to install and can provide a similar surface and appearance to solid wood flooring.

    In addition, it provides better protection and waterproofing.

    Finally, no matter which method you choose to use for second-hand wood flooring, you should remember to choose high-quality, durable flooring that will last longer and be versatile.

  5. Anonymous users2024-02-08

    Old flooring in your home may need to be replaced due to long-term use and wear and tear, or renovation needs. However, the disposal of old flooring needs to pay attention to environmental protection and safety, and the following will introduce several feasible methods to you. The first method is the old floor.

    If the material of the old floor is better, you can choose **, such as solid wood flooring, solid wood compound belt flooring, etc., which can be used to make other furniture, floor maintenance boards, etc. Some centers or second-hand markets will specialize in old flooring materials, so you can consult them first. The second method is to chop the old floor into small pieces and then use it to build a garden, flower beds, lawns, etc.

    These small blocks of flooring can beautify the environment and prevent weeds from growing, and they have a long lifespan. The third method is to cut the old floor into thin sheets and then make it into works of art, such as wooden dining tables, wooden mirror frames, wooden picture frames, etc. The colour and texture of the old floors are particularly suitable for this kind of art moulding.

    The fourth method is to use old flooring for building insulation, according to statistics, wood is more insulating than bricks, concrete and other materials. Old flooring is a green alternative to insulation. The fifth method is to shave old floors into wood chips, which are then made into wood pellet fuel for home heating and plumbing.

    This type of garbage disposal is environmentally friendly. The above are several ways to deal with old flooring at home, you can choose different ways to deal with old flooring according to different needs, and also pay attention to safety and environmental protection. When discarding the old floor, it is also necessary to pay attention to distinguishing domestic garbage and hazardous waste, and classify and dispose of it in accordance with relevant regulations.

  6. Anonymous users2024-02-07

    Your problem needs to be solved in two steps:

    1. Crunch, this is more complicated, it is generally a problem of the keel, you need to remove the floor to strengthen the keel, or simply remove the keel, do the ground level (such as Henkel's self-leveling), and then re-lay the floor;

    2. The problem of wear and tear of the wooden floor, this is simple, as long as it is a pure solid wood floor, use a sander to grind off the surface paint, and then wipe a layer of wood wax oil, with the best of "Oushi wood", pure imported from Germany, food-grade material, no pollution, the safest for the baby. Because the child is small at home, the decoration of all solid wood + wood wax oil is adopted, which is very environmentally friendly, and you can construct it yourself.

    The specific process is as follows:

    Preparation: Sanding, use a grinder to remove the ** paint (if it is new, this step is exempted);

    1. Polishing the surface of the floor with sandpaper (or 600, according to your preference, the larger it is, the finer and smoother it will be);

    2. Use medical cotton gauze (not easy to pile and less hair loss) dipped in wood wax oil and rub it vigorously on the surface (it feels like using an eraser to print the strength and angle of the pencil);

    - It can be used normally after 48 hours of complete drying, which is very convenient and environmentally friendly.

  7. Anonymous users2024-02-06

    Don't toss, wait for the kids to grow up and get a new floor.

  8. Anonymous users2024-02-05

    If it is a second-hand wood floor used by the original owner after moving, it is solid wood or parquet. You can use the Hong Kong people's practice:

    1。Please decorator on-site sanding and sanding, with a special grinding machine. It is intended to wear off the scratched paint layer of the original wooden floor.

    2。Use a vacuum cleaner to thoroughly suck out the dust from the grinding.

    3。In a dust-free environment as much as possible, use a spray gun to spray the surface of the floor with PU two-component paint.

    4。Two to four hours later, or another on-site painting. Light sand before spraying, for hairing. Dusting. Two to four hours after spraying, it is basically dry, and the window is open to disperse the smell.

    This completes the whole process and saves the money of buying new wooden floors.

    If the second-hand wood floor is laminate flooring (called "composite flooring" in the market), then if it is not damaged, it can be used directly, and if it is damaged, it will be removed. Because laminate flooring is less expensive and there is no possibility of repair.

    If my reply helps you, I for, thank you.

  9. Anonymous users2024-02-04

    Look at the floor what is going on:

    1 It's just dirty, you can find a cleaner to clean it, and then wax it.

    2 If there is damage, find a carpenter to repair it, and then wax it.

    3 It's so bad that if you don't see the cost, replace it with a new one.

    Tianjin Xinda Decoration Center can help you: 18622072797 Zhou Hua.

  10. Anonymous users2024-02-03

    Not all floors can be refurbished, depending on the type of flooring and the specific situation

    Laminate flooring refurbishment can exacerbate floor deterioration.

    The so-called floor renovation is to polish off the wear layer or damaged parts and then apply wear-resistant paint or simple waxing maintenance, but many consumers only find that the renovated floor is not only unsightly, but the fit and even the service life are sharply reduced. This is because the refurbishment technology is not up to par or the floor is not suitable for renovation.

    In this regard, experts gave renovation suggestions: laminate flooring is pressed with wood chips, and the surface is pasted with a layer of aluminum oxide wear-resistant layer, which is very thin, and such a floor cannot be renovated, when worn or damaged, it can only be replaced with a new floor, otherwise it will aggravate the aging of the floor.

    The thickness of the surface layer of the floor determines whether it can be renovated or not.

    Solid wood flooring is completely refurbished. According to the reporter's understanding, some brand manufacturers can provide renovation, but they have to charge a certain fee, generally ranging from 40 yuan to hundreds of yuan per square meter. But if the home is paved with parquet, can it also be renovated?

    This depends on the thickness of the floor surface, because the sanding is bound to reduce the thickness of the surface layer, each polishing will probably wear off the thickness of 1 to 2 mm, if the surface layer is not thick enough, wear out the solid wood surface layer to polish the middle layer, will inevitably affect the service life of the solid wood floor. The reporter saw in the market that the surface layer of multi-layer parquet generally ranges from 1 mm, and the thickness of the surface layer like this cannot be renovated. For three-layer parquet, the surface thickness of most products is about 4 mm, so that after renovation, it will not affect the middle layer of the floor.

    Therefore, whether the floor can be renovated, it is necessary to determine the thickness of the surface layer of the floor, and it is not possible to start work blindly.

    In addition, solid wood (composite) parquet flooring is made of wood of different textures or colors, and the highlight is naturally the difference between different colors.

    After consulting a number of businesses, the reporter came to the conclusion that the renovation of solid wood composite parquet flooring is not only limited by the thickness of the surface layer, but more importantly, whether the wood blocks of different colors are soaked in color, thin wood bark or surface coloring. If only the surface layer is colored, or if the veneer layer of different colors is relatively thin, then the effect of the parquet is likely to be destroyed or even disappear after sanding.

    Therefore, if you buy a solid wood composite or pure solid wood floor and consider that there is a need for renovation in the future, you must consult the merchant whether the thickness of the surface layer of the floor can meet the requirements, whether the manufacturer provides this kind of service, and you have to pay more attention to the renovation of parquet flooring.

    The above answer is provided by Matte Ya Decoration.

  11. Anonymous users2024-02-02

    Can be refurbished for use. Refurbishment should be carried out in dry weather. First of all, it is disassembled and classified according to the degree of wear. Then the installation is to install the heavily worn installation to a concealed location. The obvious position is installed in good condition, and then fixed.

  12. Anonymous users2024-02-01

    To renovate the floor, you need to first polish the old floor, remove the original paint, and then paint and polish it on site. If there is arching, deformation, etc., it needs to be re-paved. If it is a cheap hardwood floor, you need to confirm what the thickness of the skin is, and too thin hardwood flooring is not suitable for sanding.

    Because if the surface layer of the floor is too thin, the middle layer will be polished, which will affect the service life of the floor.

  13. Anonymous users2024-01-31

    Not all flooring can be refurbished.

    Ordinary hardwood flooring and three-layer hardwood flooring, especially the three-layer hardwood flooring of the icon, have a surface thickness of 3 mm or even up to 4 mm, so they are generally suitable for renovation. There is a layer of aluminum oxide wear-resistant layer on the surface of the laminate floor, and renovating the floor will destroy its wear-resistant layer and aggravate the aging of the floor. The thickness of the surface layer of multi-layer solid wood flooring varies, and the thickness of the thin skin is generally about millimeters, so the thickness of the surface layer cannot be renovated, while the thick skin can be renovated.

    If the old floor is deformed, cracked, or moldy, it is difficult to restore it to its original state even if it is renovated, and it is usually necessary to replace the wooden floor with a new one.

  14. Anonymous users2024-01-30

    Second-hand houses are replaced with new wood floors, and generally need to remove the old solid wood floors, and then follow the new floors. Follow the floor note:

    1. Usually the length of the floor is arranged in the direction of the room or along the light. It can be laid in two ways, regular or irregular. Rules laying:

    The floor is of the same length, visually arranged in a regular manner, and the relative loss is large; Irregular auxiliary equipment: adapt to the installation of the laid auxiliary floor, the length of the floor is not limited, and the loss is small.

    2. Before the floor is fixed, there should be enough equilibrium time, or have an understanding of the moisture content of the purchased floor to ensure that the moisture content of the floor is suitable for the environment.

    3. Pre-paving. Moderate adjustments should be made to the color difference of the floor. The natural color difference of the floor is objective, and a moderate color difference can effectively relieve tension and prevent "eye fatigue".

    4. According to different materials, moisture content, etc., grasp the reasonable splicing gap and the surrounding expansion space. The general materials are installed according to the seam: , the gap around the area: 8-12mm. And take out the limit block or seam insert in time.

    5. When the laying area is large, the expansion and contraction that may be caused by seasonal changes should be reasonably adjusted by dividing or crossing the bridge. It is strictly forbidden to use water-based glue.

    Fixed floors must be pre-drilled. Usually a 45° angle drill is on the tongue side, and the diameter of the drill bit is slightly smaller than the diameter of the floor nail. Floor nails shall be fixed on both sides of the end joint, and shall be matched with the ground ridge. At present, the installation of laminate flooring is mostly undertaken by flooring manufacturers.

Related questions
9 answers2024-07-13

iPhoneSE everyone knows,The machine was launched in 2016,The configuration of the machine is very good,Equipped with A9 processor,2GB running memory。 >>>More

5 answers2024-07-13

Solid wood flooring can be disassembled and used many times, this is absolutely possible. Even if the panel is spent, it won't cost a lot of money to redo the paint. When installing, pay attention to leaving space around the wall to install shrapnel in case of wet expansion and contraction.

4 answers2024-07-13

Hello car owner, second-hand car purchase, do not need to change the lock, second-hand car purchase, mainly need to pay attention to the following three points, one is the vehicle engine condition, whether the vehicle can start normally, whether there is noise after starting, idle is unstable, and then it is to test the car to see how to speed up, the engine noise is not big, and there is no burning engine oil! The second is whether there is a major accident in the vehicle as a whole, mainly the four-wheel wheel, whether there is a big impact in the front and rear, and the third is whether the vehicle is a blister car, it is best to find a professional maintenance personnel to help you check it specifically, if the above three points are not a problem, the vehicle is suitable, you can start! I hope mine can help you, you can click on the avatar to follow me and conduct one-on-one ** consultation Q&A, I will try my best to help you answer your questions, I wish you a happy life and a happy family!

25 answers2024-07-13

More than a year, estimated two years, I remember when I graduated in 07, it was popular 3800+, and the hard disk was 160. It's been more than two years now, and when I bought my notebook in December 07, everyone was on the mainstream black 5000+. However, if the computer is fine, such a configuration can still play games. >>>More

3 answers2024-07-13

RAM and graphics card are OK, separate 2G and 8G RAM. CPU bar in general. Xeon is used as a server port and for home use. >>>More