How to do the best sanitary soundproofing, and how to soundproofize the bathroom after it has been r

The pipes are running and the noise is so annoying. I believe everyone has had such an annoying experience, the wastewater from the sewer pipe often produces a lot of noise, which causes a lot of trouble to the downstairs neighbors. So, how to do a good job of sound insulation of toilet sewer pipes?

This requires the following steps to keep in mind: prepare the materials, wrap the main sewer pipe, wrap the ceiling sewer pipe, wrap the main sewer pipe with bricks and cement, and do a good job of waterproofing.

The pipes are running and the noise is so annoying. I believe everyone has had such an annoying experience, the wastewater from the sewer pipe often produces a lot of noise, which causes a lot of trouble to the downstairs neighbors. So, how to do a good job of sound insulation of toilet sewer pipes?

This requires the following steps to keep in mind: prepare the materials, wrap the main sewer pipe, wrap the ceiling sewer pipe, wrap the main sewer pipe with bricks and cement, and do a good job of waterproofing.

1. Prepare materials.

The sound insulation treatment of toilet sewer pipes should first prepare materials, and the sound insulation materials here are mainly soundproof cotton. For environmental reasons, as well as the health of your family, it is not recommended to use rock wool or other mineral wools here. In addition, it is also necessary to prepare cable ties, ropes and other materials to fix, it is not recommended to use tape, it is easy to fall off after a long time, and the effect is not good.

2. Wrap the main sewer pipe.

First of all, you need to make an accurate measurement of the size of the sewer in your bathroom, then cut the soundproof cotton prepared in advance into sections, and finally wrap them one by one on the pipe, remember to tie them strongly.

3. Wrap the ceiling sewer pipes.

Next, use the same method to bandage the sewer pipes on the ceiling. Bathroom ceilings are usually made of aluminum gusset or PVC ceilings, both of which are not soundproofed, so it is recommended to wrap the sewer pipes on the ceiling twice. In addition, it should be noted that the construction of the ceiling sewer pipe must be made before the ceiling keel construction to facilitate the construction.

Fourth, the main sewer pipe is covered with bricks and cement.

Seal the pipe with red bricks and cement treatment around the red bricks at the same time. If hollow bricks are used, the hollow part should be filled with cement.

Fifth, do a good job of waterproof treatment.

Finally, don't forget to waterproof the surface of the cement layer. Because, the soundproof cotton will be slowly eroded by the water vapor inside, and the waterproof treatment can give the soundproof cotton an extra layer of protection.

In order to win a quiet environment for yourself, your family and neighbors, and create a harmonious and warm neighborhood relationship, we must pay attention to the sound insulation of bathroom sewer pipes, and do a good job in the sound insulation treatment of toilet sewer pipes.

Make a suspended ceiling in your bathroom, the space can be a little larger, so that at least the sound of urinating upstairs will not be so clear, the sound of drainage is mainly from the drainage pipe, you can use gypsum board to wrap the drainage pipe, the sound will be much quieter.

2. When purchasing sound insulation materials, you must choose products with reliable quality. Because traditional sound insulation materials often contain some harmful substances to the body, therefore, the selection of good quality sound insulation materials can reduce the harm of harmful substances to the human body.

3. The sewer pipe is generally made of rock wool for sound insulation, but generally even if the simple sound insulation is done, the noise will still be heard, just reduced, if there are higher requirements for sound insulation, you can also use wooden boards to make a box, wrap the sewer pipe and then fill it with foaming and other sound-absorbing materials.

Jin Sanyou shares the bits and pieces of decoration every day Beijing Jin Sanyou Decoration Ten years of professionalism Focus on quality If you have any decoration problems, you can leave us a message, we also provide professional services such as house inspection, room measurement, design, etc.!

Hello dear! Glad for your question! How to insulate the bathroom after it has been renovated:

Soundproofing directly on the wall. First determine the location of the noise source and the noise volume, the location of this drain pipe is generally easy to determine, and then select the appropriate material to make a soundproof wall on the outside of the drain pipe. Sound insulation materials require large density and mass to be airtight, such as:

Bricks, acoustic panels, etc. are fine. The sound insulation effect is directly proportional to the quality of the sound insulation material used, and the greater the quality, the better the sound insulation. Smash the wall and reinstall the soundproofing cotton.

To reinstall the soundproofing cotton is to break the wall and install the soundproofing foam in the sewer pipe. If the home is a gusset ceiling, you can see all the white sewer pipes when you take off the gusset directly. Then smashed the tiles and brickwork of the riser.

1. If you don't live in the toilet, it is inevitable that the sewer pipe will have a little sound of going into the water, and if it is tightly pasted with tiles, the sound will be a little smaller. 2. Do not use wood for the bathroom door, it is best to use aluminum alloy door. The wood below the door sleeve should not be to the end, and the height of the corner line of the flat wall should be directly tiled, so as to avoid the impact of a small amount of moisture on the door sleeve and avoid mildew and blackening.

3. The most important thing in bathroom decoration is to do a good job of waterproof treatment to fully ensure that the water will not run into the room and walls, otherwise, there will be endless troubles. First, the bathroom must be made into a slope to ensure that the water will not accumulate water, and then the surface will be waterproofed Second, to choose the right waterproof material, you must use a and B set of waterproofing agent (a bag of white emulsion, a bag of gray cement) for treatment, with asphalt for a short time, after a long time will age and leak, like the so-called "waterproofing agent" is fooling. Third, the bathroom should be overhead with bricks to fully ensure that the water flows away and does not accumulate.

Kiss! Hello, happy to answer your <>

How to do sound insulation in the bathroom is as follows: remedial sound insulation depends on how the riser of the bathroom is wrapped, if it is wrapped in red bricks, and then the wall tiles are pasted, which also has the effect of sound insulation, and the problem is not big. You can go from the top of the riser, close to the top of the area, it should be untiled, there is a mouth on it, you can plug things into the gap between the riser and the tile, plug the soundproof cotton, or spray foam soundproofing material, or sand.

If it is a riser built in the way of red brick masonry, it is okay not to do sound insulation, and the top pipe can be soundproofed, and the loudest is the sewer pipe on the top surface, which can be heard by the neighbors on the upper floor. I hope mine can help you <>

Do you have any other questions that you need to consult?