What should I do if the wall tiles bulge? How to repair the tiles when they bulge

1 9 step by step reading.

Tile hollowing, because the tile and cement contact is not good and the adhesion is not tight, resulting in the middle of the air layer, if left alone, the hollow drum will further expand, it will lead to the fall off of the tile.

If you find a hollow tile, first knock out the hollow tile. Care should be taken not to destroy the surrounding tiles.

**Net-Thousands of tile hollow drum repair glue, non-stop! Ad.

After the problem tile is knocked out, the original cement needs to be further removed. Because the cement underneath is connected to each other, if it is not handled properly, the vibration will make the surrounding tiles hollow, so use a cutter to cut about 1-2 cm deep along the edge.

After the cutter finishes cutting the edges, carefully smash the cement with a chisel.

Professional ceramic tile crack repair factory direct tile crack repair high-quality business. Ad.

Remove the problematic part and you can lay new bricks. New bricks should be selected with similar colors and textures. If it is a problem found in the first decoration, then you can use the same batch of bricks, so that there will be no color difference.

Paving new bricks can be directly paved with cement, which is the traditional method. However, the cement is relatively thick, and therefore the surrounding tiles should be well protected, and it is difficult to control the thickness, which is easy to cause overall unevenness.

Now there are many glues to choose from, which can be used less, glued firmly, and even the original cement layer does not need to be cut off, which is more convenient.

After sticking, just leave it for two days without stepping on it.

If it is a large area of hollow drums, it is better to remove them all and redo them, and the overall appearance can be renewed.

If the porcelain tile wall tile is packed, the best way to deal with it is to take out the wall tile and check the inside. Then re-lay the bricks.

The tiles are bulging, and the repair method is as follows:

1. When the tiles are bulging, the raised tiles need to be taken out first, of course, the surrounding tiles cannot be damaged. The next step is to remove all the cement mortar that connects the tiles and cut them along the edges of the tiles to a depth of about two centimeters with a cutting machine.

2. Choose the same type of tile to be re-paved, which can be applied to the back of the tile through cement mortar, or re-laid on the ground through tile adhesive. Then gently tap with a rubber mace until it is flat with the rest of the tile surface. The surface of the tiles repaired in the later stage cannot be passed, and can only be used when it is completely solidified and reaches the standard of strength.

The reason why the tiles bulge.

1. After using the tiles for a period of time, there is a bulging phenomenon, which is due to thermal expansion and cold contraction. When paving tiles, there should be a certain gap, if it is too small, or even not left, in the later stage because of thermal expansion and cold contraction, if the situation is more serious, there may be hollowing, falling off, cracking problems.

2. In addition, it is related to the choice of adhesive, such as when the cement mortar is blended, the proportion is incorrect, and the mortar is not full when paving, and there will be the possibility of hollowing. And once the drum is hollowed, it will shrink later, and it will directly bulge, resulting in the separation of the tile and the ground.

The villa master provides you with local building policies, building drawings, and villa design drawings;

Villa appearance renderings service, thousands of popular drawings for you to choose.

Villa Master.

1. The tiles are completely loose! In the case of X0D X0A, the treatment method is relatively simple, first take out the bulging tiles carefully, and then clean up the dust and impurities on the back of the tile and the base part of the ground, and use special tile adhesive to paste. Because it is a floor tile, there will be certain requirements for its compressive resistance, and the tile adhesive on the back of the tile can be evenly applied to the back of the tile when pasting, so as to avoid the hollowing of the tile as much as possible.

The tile is smashed open from the middle, using a crowbar, and the damaged tile is carefully prying from the middle to the periphery, so that the jujube will not cause damage to the tiles of the surrounding spring banquet. X0D X0A can also be treated by grouting, that is, the cement mortar mixed with 108 glue penetrates from the gap of the tile to the bottom of the tile. (This treatment method is a palliative but not a cure-for-root method, can not completely solve the problem of loosening of tiles, may still appear after a long time.) ）

Kiss is a pleasure to answer for you, my answer is <> below

The first step is not to destroy the surrounding tiles, but to take down the hollow tiles; Step 2: Cut off the cement or cement on the wall with a cutting machine, and do not damage the surrounding tiles; Step 3:

Choose the same model, or similar color of the tile, if it is a porcelain piece, soak it with water, paste it with tile cement, if it is a porcelain tile, brush a layer of adhesive, dry it for a few hours, and paste it with tile cement; Step 4: Pay attention to the thickness of the cement or cement, so that the tiles will not be uneven with the surrounding tiles. In the second case, if there are only one or two loose wall tiles, they can be removed slowly, and do not destroy the tiles, the mortar cement is intact, the simple treatment method is as follows, apply glass glue to the back of the tile, not too much, otherwise it will be higher than other tiles, it is best to remove a few points of the cement layer with an anvil in advance, so that you can glue more, and it will not be higher than the surrounding tiles.

There is also a two-in-one glue or a one-o-one glue in the case of looseness. In the case of a lot of drumming, you can only smash off the repaste.

The tiles are bulging, and the repair method is as follows:

1. If the tile is completely loose, take out the bulging or bright tile, remove the stains and dust on the back of the tile and the base layer of the surface of the tile, and paste it evenly with special tile glue to avoid gaps.

2. When the tile is not completely loose, it is easy to cause damage to the tile when taking out the tile, you can smash the tile from the middle, use a crowbar to pry it open from the middle to the surrounding area, avoid damage to the surrounding tiles, and then apply tile adhesive to re-lay it.

When the wall decoration is a kind of tile that everyone likes, the householder will find that there is a hollow wall after using the tile. When encountering such a situation, the head of the household needs to know what the reason for the hollow drum is, so everyone knowsWhat should I do if the wall tiles bulge? What should I do if the wall tiles bulge?

1. There are generally several main reasons why the floor tiles bulge. We can take a look at the following points, 1. If the floor tiles are paved with joints, if the size of the gap is not properly handled, for example, the gap between the bricks and the bricks is too small (less than 2mm), and the expansion and contraction of the base layer is larger than that of the tiles (that is, the expansion rate of the two is different), which will also cause the floor tiles to bulge. When laying tiles, the unevenness of the screed layer will also cause hollowing.

2. It may also be that the quality of the original cement floor of the tile is not good, so that the cement of the tile is not well combined with the original ground, which will cause bulging. It may also be that the brand and category of floor tiles are different, we have chosen some floor tiles with a higher water absorption rate, and we have chosen seamless laying, so that the adhesive material will change depending on the working environment, which will cause the tiles to bulge.

What are the causes of bulging wall tiles.

1. The corners of the tiles are hollow. If there is a hollow drum in the corner of the wall, we need to shovel the gaps around the tiles, and then pour them with relatively thin cement and knock the tiles while pouring, so that the cement slurry can penetrate completely. This treatment saves time and effort, and is not easy to cause damage to the tiles.

2. The middle part of the tile is hollow. If there is a hollow in the middle of the tile, it is necessary to pry the tile off and re-lay it. Specifically, it is necessary to smash from the middle part of the tile, but not directly from the middle, you can use a small rhinestone to open a hole first, and then use a tool to slowly spread to the surrounding way to pry open the tile, to avoid damage to the surrounding tiles.

3. Large-area hollow drum. If there are hollows in more than 1 3 pavement areas, it is necessary to pry off all the tiles on the whole surface and re-pavement. Usually this large-area hollowing drum is caused by improper construction, and the construction party should bear the cost of tile damage and labor accessories.

4. The hollow drum falls off. If the degree of hollowing is more serious, the tile has been completely loosened or even falling off, it means that the cement mortar layer under the tile and the wall base (or ground base) have also been loosened "delamination", at this time, you can use a shovel and other tools to clean up the cement mortar layer, reapply the cement mortar and then pave the tile.

5. The degree is lighter and the location is more biased. If the tiles on the wall and floor are slightly hollowed, but do not affect the installation of cabinets, mirror cabinets, showers and water heaters, etc., and the location is also in the rear of the cabinet and cabinet and other furniture.

When the wall tiles are hollow, the householder needs to find the reason, which can be better solved. The above is the introduction of what to do about the drum of wall tiles and the reasons for the bulging of wall tiles, which is the end here.

When using tiles on the wall for laying, you must master the right method, as it can have good results and decorative properties. Otherwise, if there is a hollowing drum, it will be introduced belowWhat should I do if the wall tiles bulge? 1. The method of repairing the drum is shoveled lime sand, ash and reuse is quickly returned to provide dry putty after the end. However, some hollow drums are difficult to remove due to location and other reasons.

For example, it is more difficult to eliminate the gap between the concrete cover and the base layer. Some of the most expensive stones, hollow drums between the tiles and the base layer, the economic loss of the stone after cutting is significant.

2. This type of hollow drum can be solved by using the perfusion repair method. The high-strength adhesive can be injected into the interior of the medium-sized hollow drum, and some crack works can be grouting and repaired, and the empty position can be fully filled, and the adhesive strength and compression resistance can meet the requirements of use.

What should I do if the wall tiles bulge? On the basis of not destroying, especially in underground garages, workshops, etc., this method of grouting repair vacuum drum speed is fast, and the construction process does not affect the normal use, it is a convenient method.

1. The blowing and exhaust must be sufficient, and enough expansion joints must be retained. When laying tiles, 2-5 mm expansion joints should be reserved. If there are enough expansion joints, the expansion of thermal shock or the expansion of moisture can generate a decrease in the voltage between adjacent tiles, causing the phenomenon of empty rollers.

2. The base layer of tiled tiles must be properly disposed of. If the base layer is a new wall, the tiles should be prepared when the cement mortar is 70% dry. To avoid empty tiles, you must first clean the tile floor and the bottom of the floor.

Be sure to remove all types of dirt from your walls and water your primer a day in advance to control the humidity to 30-70%.

3. After the wall bricks are pasted on the wall, the cement needs to be cured for a period of time, and it will sink and solidify. As a result, the key link is located at the top edge of the brick wall. It simply sinks and solidifies.

Take a look at the top position of the brick. It can be seen that if the cement mortar sinks, it is usually prone to cavities. The cement mortar must be intact and homogeneous.

When mixing the back of the cement mortar scraper, it must be taken into account that the cement mortar must be sufficiently uniform and must not cut the corners.

from aboveWhat should I do if the wall tiles bulge? After the introduction, you have to grasp the right way when it comes to fixing it.

You can get it for free