What should I do if the tiles are hollow? How to deal with the hollowing phenomenon of tiles?

First of all, it depends on whether you posted it yourself or the construction team you bought the house and posted it to you, if it was you posted it yourself, you solved it yourself.

If it's posted by the construction party, you go to their contractor and ask them to rework.

And it also depends on how big the hollow drum area is? If the area is not large, forget it, re-tiling the tile is not only troublesome but also costly.

There is a hollow drum in the tile that you want to see, if it is a tile on the ground, then you often walk on it, it is likely to step on the tile, revealing a sharp edge, and if you are not careful, you will break your feet, and it will be more dangerous if you have children at home. So be sure to re-post it.

If the tiles on the wall are not to the extent that they will fall off if you touch them lightly, but the four sides are not very strong, or the center is hollow, after all, you won't touch it much, and it will generally not break.

If you stick it yourself, and you must rework, you must pay attention to some details, so as not to appear hollow after pasting, the situation: first of all, the proportion of sand cement and water should be controlled, if there is more sand or more water, it is easy to appear hollow, and the adhesive should be added to it.

There is to fully soak the tiles in the wet, otherwise the tile will still absorb water and there will still be a hollow drum, before pasting the place to paste the tile clean, and finally paste it with a leather hammer to smash it hard, so that the tile and the cement fit tightly, do the above points, to ensure that you will not have a hollow drum in the tile pasted.

1. Gently vibrate and beat with a rubber hammer to lift down the hollow drum tiles;

2. Clean up the floating mortar of the base layer of the wall and ground;

3. The adhesive mortar behind the tile is scraped off;

4. Wetting the wall of the falling place;

5. Scrape the prepared tile adhesive on the back of the tile;

6. Subsidize the wall (ground) and flatten.

7. Wipe the surface mortar with cotton silk and hook the joints.

Tile hollowing is a very common engineering defect, empty is due to the worker's behavior of leaking slurry when applying the concrete surface layer, resulting in a vacant place, so that after paving the tiles, you will find that you will knock on the vacant place with your fingers will have a crisp sound. The drum is due to the fact that the concrete surface layer is not applied flat, so that the tiles will follow the surface layer, and there will be unevenness. <>

The solution to the empty tile, if it is a vacancy in the four corners, you can use a small sharp weapon to slowly cut the tile paving gap, and then fill it with special building glue, and wait for the gel to solidify. If it is in the middle of the tile, you can knock off a whole tile and pour concrete, fill the vacant and then pave the tile.

The tile drum is difficult to solve, generally pay special attention to the surface layer of concrete, and make the surface layer flat, so as to avoid the situation of tile drum. If there is indeed a drum of tiles, you don't need to pay too much attention to it, it won't be too obvious, and a tile micro drum will not affect the overall appearance and don't need to be trimmed.

1. Gently vibrate and beat with a rubber hammer to lift the hollow drum and reed tiles;

2. Clean up the floating mortar of the base layer of the wall and ground;

3. The adhesive mortar behind the tile is scraped off;

4. Wetting the wall of the falling place;

5. Scrape the prepared tile adhesive on the back of the tile;

6. Subsidize the wall (ground) and flatten.

7. Wipe the surface mortar with cotton silk and regret the spine and hook the seams. ok

There are many reasons for tile hollowing, such as construction errors, no gaps in the tiles, poor ground quality, material problems, and rental demolition types such as low cement labeling.

The hollowing treatment method of tile corners is grouting to fill the void. The method of pouring grout directly on the four corners of the tile is very time-saving and labor-saving, and it will not damage the tile. The hollow drum treatment method in the middle of the tile is to pry the brick and repave.

If the middle of the tile is hollow, you can use a suction cup to suck out the tile, and then replace the tile with a new tile and re-lay it according to the specifications.

There is no way to remedy the large area of hollowing, so you can only pry off the entire tile and redo the base layer. The large-scale hollowing is caused by improper construction, and the construction party should be held responsible. The hollow drum falls off proves that there is a loosening between the tile and the cement mortar layer, resulting in delamination, at this time, the cement mortar layer can be cleaned with a shovel and other tools, and the cement mortar can be reapplied, and then paved.

Precautions for tiling

1. In the process of laying tiles, the fit between the tile and the wall must be greater than the gravity generated by itself. Because the tile itself has many small holes, so it will be stronger in terms of water absorption, if the dry tile is used to pave, then it will absorb the moisture in the cement to dry, so that its fit is reduced, resulting in tile hollowing and falling off.

2. Before laying floor tiles, the ground should be treated, and the level measurement is an essential item, only in this way can we understand the slope of the ground, so as to better control the paving effect of the floor tiles, and then determine the number of tiles that need to be used in each row and column according to the area of the ground and the size of the floor tiles.

How to deal with tile hollowing.

First, the tile hollow drum inspection.

First of all, it is necessary to inspect it, you can use an iron rod to knock on each brick on the wall and ground, if the sound will be dull, it means that it is pasted more firmly, on the contrary, if it is a crisp sound of "dong dong" in Xianqing, it means that the wall and floor tiles are not paved firmly, and there is a hollow drum.

Second, the treatment of different types of hollow drums.

1. Hollow corners.

If this situation occurs, it is recommended to adopt the operation mode of pouring cement slurry, which not only saves time and effort, but also does not cause damage to the brick body, the operation method is to pry open the tile gap at the corner hollow drum first, and then hit the hollow drum with a metal hammer while pouring cement slurry into the gap, so that the cement slurry can gradually fill the empty drum wheel place.

2. The middle part of the tile is hollow.

For this hollow drum method, I believe that we are more common in ordinary life, it mainly occurs in the middle of the brick, in the process of processing the tile needs to be taken out and re-paved, the operation can be used to suction cup to suck the hollow drum tile, straight out, and then the hollow drum tile according to the specification to re-pave.

3. Large-area hollow drum.

Generally speaking, if more than one-third of the pavement range appears hollow, it is recommended to pry it all off, do not be reluctant, generally speaking, this situation is mainly caused by improper construction, should be borne by the construction party to bear the cost of tile damage and artificial accessories.

4. The hollow drum falls off.

If the degree of hollowing is more serious, and even shaking and falling off, it is recommended to use relevant appliances to clean the mortar layer of cement brothers, and then reapply the cement mortar and then pave the tiles, but it should be noted that if the tiles are only partially falling off, do not hit the mortar on the foundation surface to prevent the original solid tiles around the shock.

5. The degree is lighter and the location is more biased.

If there is only a slight hollowing situation, but it will not affect the use and installation of some utensils, and the location is also behind the cabinet and other furniture, it is recommended to consider not dealing with it, of course, if it will affect the future life, it is recommended to knock off the local tiles and re-pave them according to the above situation.

Summary. Kiss, tile hollow drum is solved like this: 1

It is recommended to use high-strength tile adhesive, which is a product developed to professionally solve the problem of low water absorption tiles that are easy to hollow and fall off, and is formulated by a variety of polymer raw materials and emulsions. 2. Wait until the tiles are completely loose before taking them out, and then use a cutter to slowly remove the cement underneath and then lay them on.

Is it useful to use a hollow umbilicus?

Kiss, tile hollow drum is solved like this: 1It is recommended to use high-strength tile adhesive, which is a product developed to professionally solve the problem of low water absorption tiles are easy to hollow and fall off, and is prepared by a variety of polymer raw materials and emulsions.

2. Wait for the tiles to be completely loosened, and then take them out, and then use a cutting machine to slowly remove the cement below the wide hall, and then pave it.

Kiss, useful with hollow drums. It is useful to use and hollow drum umbilicus. Tile hollow drum repair agent using polymer latex as the main raw material, and proportionally added silicate composite material made, viscosity is very strong, and environmental performance is good, very early rock is suitable for repairing wet tiles, hollow drums, land shelter and loosening and other problems.

What are the causes of hollow tiles? How to deal with tile hollowing.

Many people have encountered the problem of "tile hollowing" after decoration, and many decoration novices feel very puzzled about it, and do not understand why there will be problems just after decoration, so what is the reason for the hollow tiles? How to deal with tile hollowing. Let's take a look at the answers we will answer for you one by one.

What are the causes of hollow tiles?

1. When the tile is paved, the mortar is not full or the tile is not gently beaten and squeezed densely;

2. The tile is not soaked in water or soaked enough before paving;

3. The plastering of the base layer of the wall is not treated as required or the garbage of the base layer is not cleaned up.

How to deal with tile hollowing.

1. In the case of a large area of tile warping or hollowing, it is necessary to remove the tiles in the original warping or hollowing area, remove the original cement mortar layer, clean the base layer, and reapply the cement mortar.

2. If the tiles can no longer be paved and used, new tiles should be purchased, and it is recommended that the owners buy more tiles when buying tiles for the first time, in case of emergency.

3. If it is within the warranty period, find a decoration company (the base installation is generally 2 years).

Precautions when tiling and plaving:

The tiles should be soaked in water for more than 2 hours before paving, so that the tiles can fully absorb water, and then take out the shade to dry or wipe the clear water; Check whether the plastering of the wall base meets the requirements, the stolen goods and dust of the wall base must be cleaned, if the stolen goods on the wall are not cleared, it will affect the paste effect of the tile, and in serious cases, the tile will fall off or the paste can not be excited; When paving, the back of the tile is covered with cement mixed mortar or 108 cement slurry and the wooden handle of a small shovel is tapped on the tile, so that the cement grout crowds the back of the tile, and then pressed hard to make the tile firmly combined with the wall base.

The above is what is the reason for the hollowing of the tiles brought to you? How to deal with tile hollowing. The contents of the mausoleum are all Ming Wangyan Department.

You can choose to fill the floor tiles in the air, fill the cement slurry around, and then you can also change the special cutting machine, leave a centimeter of shockproof joints, and gently beat with a hammer after cutting, clean up the garbage, and then use cement mortar to match the floor tiles of the same specification and number, generally use glass to suction the good corners of the paving can not affect the bricks next to it.

Tap on the surrounding area first to determine the size of the hollow drum.

There is another method commonly known as this"Injections"The relatively high cost is that the waterproofing engineering professional method is to fill the tiles with high-efficiency injections around the tiles, and some can even eliminate hollowing without removing the tiles.

This will have a great impact on you later, and its hazards will manifest itself after a few months, such as water seepage, cracking, brick loosening or direct disconnection, etc., and must be resurfaced. The causes of hollow tiles are:

1.When the tile is paved, the mortar is full (too much water in the mud) or the tile is not gently knocked and squeezed compactly, resulting in air retention;

2.The tile is not soaked in water or soaked in water for insufficient time before paving, and the cement and brick cannot be effectively bonded and form a hollow;

3.The joints left by the tiles are not wide enough, the weather is hot, and the thermal expansion and cold contraction make the tiles and cement separate to form a hollow drum;

4.The plastering of the base layer of the wall is not disposed of as required or the garbage of the base layer is not cleaned up;

It must be repaved, if it has been paved a long time ago, and you only find out now, you have to find a way to fill cement slurry between the bricks and the ground, and find a professional cement master to help you.

What are the practices for tile maintenance.

As a service in the decoration industry for 8 years, I would like to share with you some of my observations and methods, the current decoration can be said to be inseparable from ceramic tiles, even with the progress of technology, there are constantly new materials out, but to completely replace the status of ceramic tiles, it is impossible in the short term, this is related to the many advantages of ceramic tiles, first of all, ceramic tiles have high hardness, water resistance, easy to clean these advantages in one, so that other materials are temporarily no way to completely replace it, Ceramic tiles as a modern new decoration material has been more than ten or twenty years, has been in the decoration of a considerable proportion, take a house for example, the proportion of ceramic tile materials is ranked first, two positions. Of course, over the years, the more you use, the more you maintain, so let's talk about the specific maintenance of tiles.

First, the glue method, the practice is to directly use glue, glass glue, if you want to ensure the flatness of the paste, you can use marble glue or nail-free glue and glass glue together, marble glue and nail-free glue quick-drying fixed flatness, glass glue slow drying sticky firm.

Second, cement and tile adhesive paving, suitable for large-scale maintenance, the cost is not necessarily low, because cement paving is a common construction method many years ago, this method is only suitable for paving floor tiles and porcelain tiles, if you want to pave the tile on the wall, you must brush the back adhesive on the back of the tile, and brush waterproof on the wall with wet water, so as to prevent the wall water collection too quickly to produce another hollowing.

Third, the nailing method, the method is relatively simple, there are professional wall tile steel nails on the market, rust-proof, this method is to use a professional tile drill bit to open the wall bricks, directly nail the steel nails into the wall, but if you encounter a load-bearing wall, you should use a percussion drill to punch the wall, plug the expansion rubber plug and then nail or nail it with screws.

Fourth, the edge strip fixing method, this method is similar to nailing, but more beautiful than simple nailing, that is, the custom stainless steel edge strip will fix the joints of all the bricks, and then nail and fix at the position of the cross seam, so that there is no need to punch holes in the middle of the tile, and it is much better than simple nailing in terms of overall beauty.

Fifth, for a small number of corners of the hollow tile, can be treated by grouting method, treatment method: scrape the tile gap at the corner hollow drum, and fill it with cement mortar. This method can be more practical for a small number of corner tile hollows on the ground.