What is the reason for the small amount of water running after the toilet is flushed?

The toilet bowl will remain after flushing because the toilet flush valve is not closed tightly, and it can be repaired by the following methods.

Materials required: Slotted cone.

Rubber sheets, double-sided tape.

1. Remove the drainage components first, and then you can remove them by turning them.

2. Pull up the top part of the water inlet assembly, there is a red clip on the pole, reach in and touch it up and down, and the blue part at the top can be rotated and dialed up.

3. The buckle on the blue lid should be pried open first, and the upper one can be pulled out.

4. There is a special sealing ring in the middle of the bottom of the float.

Water can be injected inside and bulged up, eventually closing the inlet valve.

5. Remove the rubber gasket at the bottom of the float, paste the rubber sheet to the bottom of the gasket with double-sided tape, trim it and then install it back, so that there will be no water leakage.

The toilet uses a relatively large amount of water, how can we save water.

Here are a few tips.

1. The height of the float can be adjusted to control the water level in the tank, which determines the amount of flushing water used each time.

2. For double-speed flush toilets, press the blue button when flushing urine and use the white button when flushing stool, and the difference in water consumption between the two is very large.

3. Water seal in the toilet.

The amount of water can be adjusted simply by removing the refill pipe to prevent the water from the toilet bowl from spilling on the butt at a convenient time.

You can open the water tank to check whether the lid of the nozzle is not automatically closed, if the cover is not tight or aging, the water will keep flowing. Look at whether the ball in the tank can float on the water, if the follow-up water outlet is connected together, the ball will float on it after the water in the tank is automatically filled, and the water inlet will be closed and no longer enter the water.

The reason could be a problem with the drain valve of the toilet. The drain valve is mainly in charge of the water of the toilet tank, generally speaking, in many cases, it may cause problems with the toilet drain valve, which may be caused by cracking and deformation of the installation hole, or a series of reasons caused by uneven and uneven installation surfaces and carelessness during installation.

The toilet bowl should be covered with a lid.

If the toilet lid is opened when flushing, an instantaneous cyclone in the toilet can carry germs or microorganisms up to 6 meters into the air and remain suspended in the air for several hours before landing on walls and toothbrushes, mouthwashes and towels.

The toilet is used every day, but if you are not careful, it can also become a source of disease.

Dr. Philip Terno of New York University pointed out that in most families, toileting, washing, and showering are carried out in the bathroom, and toothbrushes, mouthwash cups, towels, etc. are shared with the toilet, which is naturally susceptible to bacterial contamination. Therefore, it is important to get into the habit of closing the toilet lid when flushing.

In this case, the water pipe of the toilet bowl is blocked, and it may be caused by the blockage of the toilet for a long time, so unscrew the soft water pipe behind the toilet bowl and clean it. Or where the toilet is connected to the water pipe. After cleaning it up again, you can install it again.

There may be two reasons for the small amount of water flowing after the toilet is flushed, one is the water ingress, the other is the drainage, and the water has been flowing after flushing, indicating that there is a problem with the drainage system, and it should be the sealing and electrical aging of the drainage or the installation not only causes water leakage, but also can replace it manually.

1.For a leaky toilet in the back row, it is possible that the float in the tank is not buoyant enough. Nowadays, many toilet tanks are small, which can save water, but the disadvantage is also obvious, that is, the buoyancy of the float is not enough.

The toilet tank is not cleaned, and the water outlet cannot be sealed with the water parts, resulting in continuous leakage in the water tank, but it is not necessarily broken.

1. Whether there are cracks in the toilet water tank. If there is a problem with the burning of the toilet, cracks may appear, causing the toilet tank to leak. Although it can be used with proper repairs, it is advisable to replace the toilet bowl as it may leak after repairs.

2. The aging of the internal parts of the water tank may also lead to the leakage of the toilet water tank. Open the toilet tank lid and inspect it carefully. For example, the drain switch is sometimes pressed but fails to pop out.

At this point, the parts can basically be replaced. There is no need to replace the toilet.

3. If there is no leakage in the toilet tank, you can check whether the sewer is in good condition. Leaks at the lower part of the toilet tank and the connection of the water pipe are also common, so it is important to double-check that the connection is intact.

4. The toilet float is also an important component that needs to be checked. The water float determines the water level of the toilet tank. If there is no problem with the water float, the toilet tank will still flow after it is full, causing a water leak.

If there is a problem with the water float, you can choose to replace it. You can buy one online for a few dozen dollars, but you should also choose based on your toilet model.

5. The leakage of the flush toilet may also be due to the problem of the sewer pipe below. It is a pipe that transports water mainly to the toilet tank, and it is very likely here.

The reason why the toilet does not stop flowing after use is that the plastic gasket on the outlet hole of the pumping system is aging and elastic enough to be sealed. Solution: 1. Whether the black semi-circular float on the overboard assembly is properly covered, or the black semi-circular float falls off, or the rope is stuck or the black semi-circular float is deformed; 2. The single toilet downspout component is shaken by hand, if it shakes, it means that the semicircular fixing piece at the bottom of the downspout component is broken or loose.

Start by pressing the drain button to see if the flow can stop.

If it doesn't work, then you need to open the water tank cover, check whether the water tank cover button and the button on the drain valve can easily pop up, if there is a card or a light press to the end, it is a problem with the water tank button or water button.

The key switch of some flush toilets will occasionally get stuck after being worn for a long time and cannot be restored.

Solution: Quickly press and release the key switch, preferably twice or more in a row, until the key switch returns to its usual strength, and the switch can be reset after repeating it a few times.

After treatment, the sound of water storage in the water tank is getting smaller and smaller, which means that the water tank has been restored, and when the water is full, there will be no more water in the toilet.

The next time you encounter this situation, you can follow the above methods.

In addition, every time you use the water tank, try to press the button that will not get stuck to reduce the leakage of jamming.

Your water level is set too high, and the water will flow out of the toilet if it goes through the overflow hole next to the drain valve. Rotate the screw of the inlet valve counterclockwise to lower the water level, and the water will not pass through the overflow hole after the water is loaded, and it will be fine.

You need to open the water tank cover to see the water tank level, if the water is full, there is a problem with the water inlet valve, if the water is not satisfied, it is the reason for the drain valve, if you can't repair it, you can only replace the valve with a problem.

This problem usually occurs when the valve is the case. Didn't close it properly. Can you flush the water a few more times and see if it automatically works?

If there is still a problem. Lift the calcium from the water storage tank to see if something is stuck, and manually press it to try. If it is still not good, you can only find a master to repair it.

It should be that the water valve of the water tank is not tightly sealed, and the toilet is not fully closed after operation, so it can be checked and replaced.

In this case, the inlet and outlet valves in the flush bucket are broken, and the valve can be replaced.

Sometimes, the drain valve will also get stuck, and if you press it again or a few times, it may be fine.

The float in the toilet bowl is broken.

In this case, you look at the above according to whether the valve is not talked about.

1. Remove the lid from the toilet bowl and press it with your hand when flushing if the small ears are stuck, if pressed, the ears will usually return to their original position. Flowed.

2. Look down at the rubber shaft, look at the rubber washer (black, round about cm, easy to find), if there is a foreign object to grab. Usually, it is pressed flat against the toilet drain and removed from foreign objects.

3. If all the above operations are normal, the rubber gasket must be seriously deformed. Replace the gasket. : Pants should not be washed frequently, especially jeans. You can wear them during the day and blow them in a ventilated place at night.

2. It is best to wear clothes during the day and not at night, so the taste will be much smaller.

It seems that there is more than just water inside.

Two solutions to the problem:

1: Drain the water, and then pull the cup up and down with your hands to see if it can return to its original position, it may be stuck. If you're lucky, you can.

2: Change the water inlet parts and solve the problem once and for all.

wading all the time; There are three reasons for this.

1.The flap is not properly covered. Resting on it. It's good to do it manually, not to rule it out; It's been years. There is also a leak on the flap cover.

Replace the flip cover. 2.The float rests underneath. It's not just water. Just do it manually.

3.The water stop valve of the float is not only water, so it has been wading. Flowing from the overflow pipe. It's going to be changed.

The water on the water has drifted into the sand. Or the gasket of the water control water on the water is long-lived.

Replace the accessories inside the water tank and look at the ** is not a problem.

Summary. The reason could be a problem with the drain valve of the toilet.

The drain valve is mainly in charge of the water of the toilet tank, generally speaking, in many cases, it may cause problems with the toilet drain valve, which may be caused by cracking and deformation of the installation hole, or a series of reasons caused by uneven and uneven installation surfaces and carelessness during installation.

What is the reason for the small amount of water running after the toilet is flushed?

Hello, I am helping you to inquire about the relevant information and will reply to you immediately.

The reason could be a problem with the drain valve of the toilet. The drain valve is mainly in charge of the water of the toilet tank, generally speaking, in many cases, it may make the toilet drain type valve problems, which may be the installation hole cracked and deformed, or the installation surface is uneven and the installation is not careful caused by a series of reasons.