What should I do if the toilet doesn t go water?

If the toilet bowl does not go to water, you need to repair the water valve, the steps are as follows:

Step 1: Close the water supply valve and remove the water supply pipe. Open the toilet tank cover, remove the blue cap of the water valve, and remove the water valve assembly as a whole.

Step 2: Rotate the top cover counterclockwise to remove it, flip it over and take a photo as follows.

Step 3: Remove the white hard sheet and black rubber.

Step 4: Use transparent glue to enlarge the central shaft, the purpose is to reduce the center clearance.

Step 5: Replace the lid back into the water appliance.

Step 6: Replace the float, install the water supply valve as a whole, and connect the water pipe. Install a water supply pipe and a blue upper cover, and test the boiling water.

1. Check whether there is tap water.

Turn on other faucets, check if there is running water, and rule out external causes first.

2. Check whether the angle valve is closed.

Check that the toilet valve has not been accidentally closed and that the angle valve is open.

3. Check whether it is blocked by scale.

Take out the filter inside the tank and see if there are too many impurities, blocking the filter and causing tap water to not come in. If so, clean the filter and you're good to go.

4. Check whether there is a problem with the water tank button.

Check if there is a problem with the spring of the tank button, and if it is stuck, just flip it. If the spring of the tank button loses its elasticity, go to the hardware store and buy one to replace it, and the water can be restored to normal intake.

5. Check whether there is a problem with the water inlet valve.

Open the water tank and toggle the water inlet valve to see if water can be entered. Check whether the water inlet valve is stuck and the water cannot be entered.

6. Check whether the float and float are stuck.

Check whether the float or float is stuck and see if it can move freely. If the float or float fails, it will also cause water to not enter.

Reasons why the toilet does not go water:1. There are many magazines in the water tank, and the water tank is blocked; 2. The water inlet valve is pushed to the water tank cover; 3. The button spring on the water tank is damaged.

1. The accumulation of impurities in the water tank will cause the water tank to be blocked, and the water tank can be cleaned with a waste toothbrush or some cleaning items.

2. If the inlet valve of the toilet reaches the lid of the water tank, the toilet tank will not be filled with water.

3. The reason for the failure of the button on the toilet tank, the spring of the internal button loses its elasticity, and it is necessary to purchase a button of the corresponding size for a replacement.

4. If you can't solve it yourself, it is recommended to click below to make an appointment with a nearby master in the same city to quickly come to solve it for you.

1.Find the manufacturer to repair**, or professionally repair the toilet**, contact for repair. 2.

Repair it yourself, the principle of the method is as follows: there are many reasons why the toilet can't pump water. In fact, it is very simple to investigate, and follow the flow to find it.

Troubleshoot step by step. Open the main valve [also called angle valve] to determine whether there is running water, open the water tank cover, and observe that the water tank is not watered. Whether the piston can be plugged.

If it can't be plugged, it will leak, the water tank is not satisfied, the switch can't reach, so the water tank accessories of the toilet are divided into three parts. The first is that the drain valve is directly below the button, and the second is the inlet valve, which is the part of the hose connected to the outside of the water tank, which is generally next to the drain valve. The third part is that the buttons are divided into full-row buttons and half-row buttons.

Close the toilet lid and see if the button can reach the inlet valve, if so, adjust the inlet valve to see if the float or float of the inlet valve can move up and down freely. If you get stuck, the water won't get in. Usually there are adjustable crosseyes on the pontoons, and you can twist them in a clockwise direction to see.

If the float is suspended in the air when there is no water, it means that it is broken and the water inlet is blocked. Fill the tank with water to see if the pontoons can float freely. If the problem of water inlet is solved.

Then there is the problem of drainage, which is also the problem of flushing. See if the plug of the plug in the tank, also called the float, is damaged. Whether the float and button connection are loose.

If it is loose, tighten it to see if the button is elastic. It is easy to rust when the spring enters the water for a long time. The working principle of the toilet is nothing more than pumping--- storing water --- releasing water.

Just a few things, step by step. 3.Use a basin to catch water, hand the toilet.

4.Disable, find a nearby public toilet, quite exercised.

The reasons are: the water pressure in the home is too low, and the main water gate can be fully opened to increase the water pressure; If the paper scraps are blocked, you can use the software to dredge the pipe to hook up the blockage of the toilet, or pour the caustic soda into the boiling water, and pour it into the toilet bowl after it melts; The filter screen is clogged with scale, and the filter screen needs to be cleaned; The toilet parts fall off and need to be replaced; If the inlet and outlet valve is faulty, you need to observe whether there is something pushing up to the inlet valve, and if so, you need to adjust the position of the inlet valve and then open the water inlet.